Quick Installation Guide Version 1.
Copyright© 2006 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer. Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequen-tial damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Warning Panel PC and their components contain very delicate Integrated Circuits (IC). To protect the Panel PC and its components against damage from static electricity, you should always follow the following precautions when handling it : 1. Disconnect your Panel PC from the power source when you want to work on the inside 2. Hold the board by the edges and try not to touch the IC chips, leads or circuitry 3. Use a grounded wrist strap when handling computer components. 4.
Getting Started This section will help you have your P0715 up and running smoothly. PACKING LIST P0715 9 x Screws 1 x Arm Holder Bracket 2 x Wall Mount Bracket 1 x Adaptor 2 x Power Cord (American & French Cordset) 1 x Driver CD Before up and running, please make sure the package contains all of above accessories. If any of the above items is damaged or missing, contact your vendor immediately.
Specification Panel PC P0715 Model Name Cache Intel Low Voltage Celeron 400~733MHz CPU FSB100/133MHz 2nd Level 256K Memory 1 x 144Pin SO-DIMM up to 512MB SDRAM VRAM SMI722 G8 Lynx 3D+ engine 8MB Video RAM on chip Chipset Intel 815E + Intel CH2 ATA / IDE Ultra DMA 33, support 2 IDE device Audio Realtek ALC202A AC97 Codec, support Line-out Watchdog Timer 127-level Reset System Fan 1 x 4cm x 4cm / 8 CFM Serial Port 2 x RS-232 ports (COM1/2) USB Port 2 x USB 1.
Mounting Arm Mounting Hook Mounting 6 P0715 Quick Installation
Dimension Unit: mm P0715 Quick Installation 7 7
OSD of Front Panel 8 P0715 Quick Installation
Location of I/O Ports Before starting to install software on your new Panel PC please spend some time to find out the exact location of connectors and HDD (if pre-installed). The front panel does not contain any indicators, switches, connectors or drive access. All these are to be found on the left and right side and on the rear of the system.
Connecting Peripherals The user can use the I/O interfaces located at the backside of the chassis to connect external peripheral devices, such as a mouse, a keyboard, a monitor, serial devices or parallel printer etc. Before connection, make sure that the computer and the peripheral devices are turned off. Connecting an external CRT P0715 has a 15-pin analog RGB interface connector located at the rear side of the chassis.
LAN Port P0715 provides one Intel 82562ET 100/10 Base-T Ethernet (RJ-45) interface. For network connection, follow the instructions below; 1. Turn off the Panel PC system and the Ethernet hubs. 2. Plug in one end of cable of a 100/10 Base-T hub to the system's RJ-45 jack. USB Ports P0715 provides four external USB ports to connect to external USB devices. USB ports and devices are hotplug capable. Therefore any USB device can be connected at all time without the need to power down your system.
Hardware Installation HDD installation 1. On the back of P0715, locate the screws that secure the rear case. Use screw driver to remove the screws. Keep the screws safely for later use. Pull the baffle slightly upward the main unit until it is disengaged from main unit. 2. Put the HDD into the drive bay and screw it on.
44 pin IDE Cable 2.5" HDD Pin 1 Pin 1 Note: Beware of the directions when wiring HDD and IDE cable.
Panel PC Installation 1. In 2.4B or above Driver, choose Drivers & Utilities.
1.1 Select Panel Computing.
1.2 Select P0715.
1.3 Install All Drivers.
2. Install Touch Screen Driver.
4. Select Promote Touch Driver to install.
