MB898/MB898F/ MB898RF Socket LGA775 Pentium® 4 Intel® Q965 Chipset Industrial Motherboard USER’S MANUAL Version 1.
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction ....................................................... 1 Checklist .............................................................................. 1 Product Description ............................................................. 2 Specifications ...................................................................... 3 Board Dimensions ............................................................... 4 Installations .......................................................
This page is intentionally left blank.
INTRODUCTION Introduction Checklist Your MB898/MB898F Pentium® 4 motherboard package should include the items listed below: • The MB898/MB898F motherboard • This User’s manual • 1 Back I/O shield • 1 IDE cable • 1 Floppy cable • 1 SATA cable • 1 Serial-Port cable • 1 CD containing the following: • Chipset Drivers • Flash Memory Utility MB898 User’s Manual 1
INSTALLATIONS Product Description The MB898/MB898F LGA 775 Pentium® 4 motherboard incorporates the Intel Q965 chipset that can utilize a single LGA775 processor of up to 4.0GHz or higher and supports FSB frequency of 533/800/1066Mhz (133MHz(533MT/s), 200MHz(800MT/s) and 266MHz(1066MT/s) HCLK respectively. The Q965 chipset is designed for use with the Pentium® 4 processor with 1M Level 2 (CPU integrated) cache.
INTRODUCTION Specifications MB898/MB898F Socket LGA775 Pentium® 4 ATX Motherboard w/ Intel® Q965 Chipset Features System CPU System Memory System Chipset BIOS Watchdog Timer SSD H/W Monitor Expansion Slot Graphics VGA Controller VGA Memory LCD Interface Ethernet Controller Connector Multi I/O Chipset USB Audio Others Supports Intel Core 2 Duo / Pentium® D / Pentium® 4 HT / Celeron® D processors Up to 3.8GHz+, 533MHz/800MHz/1066MHz FSB DDR2 DIMM x 4, max.
INSTALLATIONS Board Dimensions 4 MB898 User’s Manual
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the MB898/MB898F in order to set up a workable system. The topics covered are: Installing the CPU ........................................................................ 6 ATX Power Installation ............................................................... 6 Installing the Memory .................................................................. 7 Setting the Jumpers ................................
INSTALLATIONS Installing the CPU The MB898/MB898F motherboard supports an LGA 775 processor socket for Intel® Pentium® 4 processors. The LGA 775 processor socket comes with a lever to secure the processor. Refer to the pictures below, from left to right, on how to place the processor into the CPU socket. Please note that the cover of the LGA775 socket must always be installed during transport to avoid damage to the socket.
INSTALLATIONS Installing the Memory The MB886/MB898F motherboard supports four DDR2 memory sockets for a maximum total memory of 8GB in DDR memory type. It supports DDR2 533/667/800. Basically, the system memory interface has the following features: Supports two 64-bit wide DDR data channels Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel mode and 12.8GB/s (DDR2 800) in dual-channel mode. Supports 256Mb, 512Mb, 1Gb DDR2 technologies.
INSTALLATIONS Setting the Jumpers Jumpers are used on MB898/MB898F to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on MB898/MB898F and their respective functions. Jumper Locations on MB898/MB898F .......................................... 9 JP8, JP9, JP10: RS232/422/485 (COM2) Selection ..................... 10 JP6: IDE DMA Mode Setting .................
INSTALLATIONS Jumper Locations on MB898/MB898F Jumper Locations on MB898/MB898F .......................................... 9 JP8, JP9, JP10: RS232/422/485 (COM2) Selection ..................... 10 JP6: IDE DMA Mode Setting....................................................... 11 JBAT1: Clear CMOS Contents .................................................... 10 JP1: Boot Device Selection………………..……………………..11 JP5: Configure and Recovery…………………………………… 11 JP11: Processor Setting ...............................
INSTALLATIONS JBAT1: Clear CMOS Contents Use JBAT1, a 3-pin header, to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the motherboard before clearing CMOS.
INSTALLATIONS JP6: IDE DMA Mode Setting JP6 Setting Function Pin 1-2 Short/Closed Master (default) Pin 1-2 Open Slave JP8, JP9, JP10: RS232/422/485 (COM2) Selection COM1 is fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485. COM3 and COM4 are fixed for RS-232 use only. The following table describes the jumper settings for COM2 selection.
INSTALLATIONS Connectors on MB898 The connectors on MB898/MB898F allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on MB898 and their respective functions. ATX1: 24-pin ATX Power Connector................................................. 14 ATX2: ATX 12V Power Connector .................................................... 14 MB898/MB898F Edge Connectors .....................................................
INSTALLATIONS Connector Locations on MB898/MB898F ATX1: 24-pin ATX Power Connector ...................................................................................................................14 ATX2: ATX 12V Power Connector ......................................................................................................................14 MB898/MB898F Edge Connectors........................................................................................................................
INSTALLATIONS ATX1: 24-pin ATX Power Connector Signal Name 3.3V -12V Ground PS-ON Ground Ground Ground -5V +5V +5V +5V Ground Pin # 13 14 15 16 17 18 19 20 21 22 23 24 Pin # 1 2 3 4 5 6 7 8 9 10 11 12 Signal Name 3.3V 3.3V Ground +5V Ground +5V Ground Power good 5VSB +12V +12V +3.
INSTALLATIONS VGA1: VGA CRT Connector VGA1 is a DB-15 VGA connector located beside the COM1 port. The following table shows the pin-out assignments of this connector. Signal Name Red Blue GND GND VCC N.C. HSYNC DDCCLK Pin # 1 3 5 7 9 11 13 15 Pin # Signal Name 2 Green 4 N.C. 6 GND 8 GND 10 GND 12 DDCDATA 14 VSYNC CN1: Parallel Port Connector CN1 is a DB-25 external connector situated on top of the VGA and serial ports.
INSTALLATIONS CN2, J10, J6, J5: COM1/2/3/4 Serial Ports CN2 (COM1) is a DB-9 connector, while J10, J6 and J5 are a COM pin-header connectors. COM1 Signal Name DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground COM2 Pin # 1 2 3 4 5 Pin # 6 7 8 9 10 Signal Name DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used COM2 is jumper selectable for RS-232, RS-422 and RS-485.
INSTALLATIONS CN4: Audio Connector USB6: USB6/7 Connector USB_LAN1: 10/100 or GbE RJ-45 and USB4/5 Connector Note: 10/100 LAN for MB898; Gigabit LAN for MB898F/MB898RF F_USB1: USB0/USB1 Connector Signal Name Vcc D0D0+ Ground Pin 1 3 5 7 Pin 2 4 6 8 Signal Name Vcc D1D1+ Ground NC 9 10 Ground MB898 User’s Manual 17
INSTALLATIONS F_USB2: USB2/USB3 Connector Signal Name Vcc D2D2+ Ground Pin 1 3 5 7 Pin 2 4 6 8 Signal Name Vcc D3D3+ Ground NC 9 10 Ground Signal Name Vcc D8D8+ Ground Pin 1 3 5 7 Pin 2 4 6 8 Signal Name Vcc D9D9+ Ground NC 9 10 Ground F_USB3: USB8/USB9 Connector S_ATA1,S_ATA2,S_ATA3,S_ATA4,S_ATA5,S_ATA6: SATA0/1/2/3/4/5 Connector Pin # 1 2 3 4 5 6 7 Signal Name Ground TX+ TXGround RXRX+ Ground Note: S_ATA5 and S_ATA6 MB898F only 18 MB898 User’s Manual
INSTALLATIONS IDE1: Primary IDE Connectors IDE1 Signal Name Reset IDE Host data 7 Host data 6 Host data 5 Host data 4 Host data 3 Host data 2 Host data 1 Host data 0 Ground DRQ0 Host IOW Host IOR IOCHRDY DACK0 IRQ14 Address 1 Address 0 Chip select 0 Activity Pin # 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Pin # 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal Name Ground Host data 8 Host data 9 Host data 10 Host data 11 Host data 12 Host data 13 Host data 14 Host data 15 Pro
INSTALLATIONS SYS_FAN1: SYSTEM Fan Power Connector Pin # 1 2 3 4 Signal Name Control Sense +12V Ground NB_FAN1: Northbridge Fan Power Connectors Pin # 1 2 3 Signal Name Sense +12V Rotation detection J1: Audio Front Header Signal Name MIC2_L MIC2_R Line2_L Sense Line2_R Pin # 1 3 5 7 9 Pin # 2 4 6 8 10 Signal Name Ground Presence# MIC2_ID NC Line2_ID J2: HDMI Audio Connector J2 is a HDMI Audio connector. The following table shows the pin-out assignments of this connector.
INSTALLATIONS J8: System Function Connector J8 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended. Pin # 1 2 3 4 Signal Name Speaker out No connect Ground +5V Power LED: Pins 11 - 13 The power LED indicates the status of the main power switch.
INSTALLATIONS Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header. Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.
INSTALLATIONS J12: Digital I/O Connector (4 in, 4 out) This 10-pin digital I/O connector supports TTL levels and is used to control external devices requiring ON/OFF circuitry.
INSTALLATIONS Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
INSTALLATIONS printf("System will reset after %d seconds\n", bTime); EnableWDT(bTime); return 0; } //======================================================================= void copyright(void) { printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO DETECT) ========\n"\ " Usage : W627E_WD reset_time\n"\ " Ex : W627E_WD 3 => reset system after 3 second\n"\ " W627E_WD 0 => disable watch dog timer\n"); } //======================================================================= void EnableWDT(int interv
INSTALLATIONS //======================================================================= // // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //======================================================================= ==== #include "W627EHF.H" #include
INSTALLATIONS Lock_W627EHF(); } //======================================================================= void Set_W627EHF_Reg( unsigned char REG, unsigned char DATA) { Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, REG); outportb(W627EHF_DATA_PORT, DATA); Lock_W627EHF(); } //======================================================================= unsigned char Get_W627EHF_Reg(unsigned char REG) { unsigned char Result; Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, REG); Result = inportb(W627EHF_DATA_PORT);
INSTALLATIONS File of the Main.cpp //===================================================================== // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. //===================================================================== #include #include #include #include #include "W627HF.
BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction ........................................................................ 30 BIOS Setup ................................................................................... 30 Standard CMOS Setup ................................................................. 32 Advanced BIOS Features .................................
BIOS SETUP BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ESC : Quit F10 : Save & Exit Setup Ç È Æ Å : Select Item Time, Date, Hard Disk Type… The section below the setup items of the Main Menu display
BIOS SETUP Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
BIOS SETUP To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time. Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the / or +/- keys to set the current time.
BIOS SETUP Drive A / Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer. The available specifications are: 360KB 1.2MB 720KB 1.44MB 2.88MB 5.25 in. 5.25 in. 3.5 in. 3.5 in. 3.5 in. Video This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode.
BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP Hyper-Threading Technology Hyper-Threading Technology enables two logical processors on a single physical processor by replicating, partitioning, and sharing the resources within the Intel NetBurst microarchitecture pipeline. Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items.
BIOS SETUP Typematic Rate (Chars/Sec) When the typematic rate is enabled, the system registers repeated keystrokes speeds. Settings are from 6 to 30 characters per second. Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. Security Option This field allows you to limit access to the System and Setup. The default value is Setup.
BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset.
BIOS SETUP Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main items for user to select. Once an item selected, a submenu appears. Details follow.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility 2nd Super IO Device Onboard Serial Port 3 Serial Port 3 Use IRQ Onboard Serial Port 4 Serial Port 4 Use IRQ 3E8h IRQ11 2E8h IRQ10 ITEM HELP Menu Level > Phoenix - AwardBIOS CMOS Setup Utility USB Device Setting USB 1.0 Controller USB 2.
BIOS SETUP SATA Mode The setting choices for the SATA Mode are IDE, RAID and AHCI Mode. Select [IDE] if you want to have SATA function as IDE. Select [AHCI] for Advanced Host Controller Interface (AHCI) feature, with improved SATA performance with native command queuing & native hot plug. Select [RAID] to use SATA as RAID function. RAID function is supported on the board if it uses ICH8R. (MB898RF supports 6 x SATA with RAID.
BIOS SETUP Parallel Port Mode This field allows you to determine parallel port mode function. SPP Standard Printer Port EPP Enhanced Parallel Port ECP Extended Capabilities Port ECP+EPP Combination of ECP and EPP capabilities Normal Normal function Intel 82562V LAN Control (MB898) By default, this setting is Enabled. USB 1.0 Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. USB 2.0 Controller The options for this field are Enabled and Disabled.
BIOS SETUP Power Management Setup Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled ACPI Suspend Power Management Video Off Method Video Off In Suspend Suspend Type Modem Use IRQ Suspend Mode HDD Power Down Soft-Off by PWR-BTTN Resume by Alarm Date (of Month) Alarm Time (hh:mm:ss) Alarm S1(POS) User Define V/H SYNC+Blank Yes Stop Grant 3 Disabled Disabled Instant-Off Disabled 0 0:0:0 ** Reload Global Timer Events ** Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary
BIOS SETUP Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows BIOS to control the video display. Blank Screen Writes blanks to the video buffer. Video Off In Suspend When enabled, the video is off in suspend mode. Suspend Type The default setting for the Suspend Type field is Stop Grant. Modem Use IRQ This field sets the IRQ used by the Modem.
BIOS SETUP PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Shutdown Temperature CPU Warning Temperature System Temp CPU TEMP System Fan Speed CPU Fan Speed Power Fan Speed Vcore 12 V 1.8 V 5 V 3.3 V VBAT (V) 5VSB(V) Disabled Disabled 32°C/89°F 39°C/102°F 0 RPM 4500 RPM 0 RPM ITEM HELP Menu Level > 1.26 V 12.45 V 1.90 V 5.22 V 3.36V 3.18 V 5.
BIOS SETUP Frequency/Voltage Control Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI Clk Disabled Spread Spectrum Disabled ITEM HELP Menu Level > Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock. Spread Spectrum This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only.
BIOS SETUP Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. Load Optimized Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. Set Supervisor/User Password These two options set the system password.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 2000 and Windows XP. The software and drivers are included with the board. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel Q965 Chipset Software Installation Utility錯誤! 尚未定義書籤。 Intel Q965 Chipset Graphics Driver ........ 錯誤! 尚未定義書籤。 Realtek Codec Audio Driver Installation .
DRIVERS INSTALLATION Intel Q965 Chipset Software Installation Utility The Intel® Q965 Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 2000/XP. (Before installed Intel Chipset Software Installation Utility,Please update your system to Windows 2000 SP4 or Windows XP SP1A) 1. Insert the CD that comes with the board and the screen below would appear.
DRIVERS INSTALLATION 2. When the Welcome screen appears, click Next to continue. 3. Click Yes to accept the software license agreement and proceed with the installation process. 4. On the Readme Information screen, click Next to continue the installation. 5. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect.
DRIVERS INSTALLATION Intel Q965 Chipset Graphics Driver Follow the instructions below to complete the installation under Windows 2000/XP. 1. Insert the CD that comes with the board and the screen below would appear. Click Intel (R) Q965 Chipset Drivers, then Intel (R) Q965 Chipset Family Graphics Driver. 2. When the Welcome screen appears, click Next to continue.
DRIVERS INSTALLATION 3. Click Yes to accept the software license agreement and proceed with the installation process. 4. On Readme File Information screen, click Next to continue. 5. On Setup Progress screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect.
DRIVERS INSTALLATION Realtek Codec Audio Driver Installation 1. Insert the CD that comes with the board and the screen below would appear. Click Intel (R) Q965 Chipset Drivers, then Realtek High Definition Codec Audio Driver. 2. When the Welcome screen appears, click Next to continue. 3. The Setup process is now complete. Restart the computer when prompted for changes to take effect.
DRIVERS INSTALLATION Intel LAN Drivers Installation Follow the steps below to start installing the Intel PCI Express Gigabit LAN drivers. 1. Insert the CD that comes with the board. On the initial screen, Click Intel (R) Q965 Chipset Drivers, then Intel(R) PRO LAN Network Drivers. 2. On the next screen, click Install Drivers to start the drivers installation.
DRIVERS INSTALLATION 3. When the Welcome screen appears, click Next to continue. 4. In the License Agreement screen, click I accept the terms in license agreement and Next to accept the software license agreement and proceed with the installation process. 5. When the Setup Type appears, click Complete and Next to continue. 6. When the Ready to Install the Program screen appears, click Install to continue. 7. The Setup process is now complete (InstallShield Wizard Completed).
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses that also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.
