HS-2606 ULV Intel® Celeron® processor Embedded Engine Board ‧CompactFlash‧PCMCIA‧Mini PCI‧ ‧SO-DDR‧CRT/Panel‧TV-Out‧LAN‧Audio‧ ‧ATA/33/66/100‧4 COM‧USB2.
Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s).
Table of Contents Chapter 1 General Description ..................................1 1.1 Major Features ....................................................................... 2 1.2 Specifications ........................................................................ 3 1.3 Board Dimensions................................................................. 4 Chapter 2 Unpacking ..................................................5 2.1 Opening the Delivery Package............................................
Chapter 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 Chapter 5 5.1 5.2 5.3 5.4 AMI BIOS Setup ..................................... 25 Starting Setup...................................................................... 25 Using Setup ......................................................................... 26 Main Menu............................................................................ 27 Standard CMOS Setup ........................................................
Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body.
Chapter 1 General Description The HS-2606 is a 100MHz FSB VIA CLE266/VT8235 chipset-based board designed for ULV Intel® Celeron® processor 400/650MHz. These features combine and make the HS-2606 an ideal all-in-one industrial single board computer. Additional features include an enhanced I/O with CompactFlash reader, PCMCIA, CRT/Panel, audio, LAN, TV-Out, 4 COM, and USB2.0 interfaces.
Additional onboard connectors include four advanced USB2.0 port providing faster data transmission. And one external RJ-45 connector for 10/100 Based Ethernet use. 1.1 Major Features The HS-2606 comes with the following features: ULV Intel® Celeron® processor 400/650MHz One SO-DDR socket with a max.
1.
1.
Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-2606 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. 2.2 Inspection After unpacking the board, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment.
NO. 1 2 3 4 5 6 Cables Package Description 4-pin power cable x 1 MIC/Audio cable x 1 8-pin USB split type cable x 1 PS/2 KB/MS transfer cable x 1 RS-232 cable x 4 IDE flat cable x 1 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately.
Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-2606. This chapter also contains information related to jumper settings of switch, and the watchdog timer selection etc. 3.1 Before Installation After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process. 1.
3.
3.3 Jumper List Jumper JBAT1 JP2 3.4 Default Setting Clear CMOS: Normal Operation Panel Voltage Select: +3.
3.6 System Memory The HS-2606 provides one 200-pin SO-DDR socket at locations DIM1. The maximum capacity of the onboard memory is 1GB. 3.7 CMOS Data Clear The HS-2606 has a Clear CMOS jumper on JBAT1. JBAT1: Clear CMOS Options Settings Normal Operation (default) Clear CMOS Short 1-2 Short 2-3 1 3 IMPORTANT: Before you turn on the power of your system, please set JBAT1 to Short 1-2 for normal operation. 3.8 Power and Fan Connectors HS-2606 provides one 4-pin power connectors at CN1.
CN2: External VCC Out Connector PIN Description 1 2 3 4 VCC GND GND VCC 1 4 CN4: External Reset Button PIN Description 1 2 3 4 RST_SW GND GND GND 4 3 2 1 GND +5V N/C 1 N/C Description 1 2 3 +5V PIN GND FN1: Fan Connector 3 Connector FN1 onboard HS-2606 is a 3-pin fan power output connector. And HS-2606 supports +5V Fan only. 3.9 System Front Panel Connectors The HS-2606 has one LED at location J2 that indicates the power-on status.
Connector J2 Orientation HDD LED PWR Button 1 2 3 4 5 6 7 8 9 10 11 12 SPEAKER PWR LED RST_SW 3.10 VGA Controller The HS-2606 provides two connection methods of a VGA device. CN7 offers a single standard CRT connector while LCD1 is the 44-pin panel connector. VIA CLE266 VGA chipset shared main memory 8/16/32MB, and provides high quality DVD video playback. HS-2606 also provides Hardware MPEG-2.
N/C N/C FPBKLP GFPHS GFPVS N/C GFPD23 GFPD21 GFPD19 GFPD17 GFPD15 GFPD13 GFPD11 GFPD7 GFPD5 GFPD3 GFPD9 N/C N/C GND GFPDEN SHFCLK N/C GFPD22 GFPD20 GFPD18 GFPD16 GFPD14 GFPD12 GFPD10 GFPD8 GFPD6 GFPD4 GFPD2 GFPD0 43 ENPVEE 1 VLCD 44 GND 2 N/C NOTE: GFPD1 GFPD9 GFPD11 GFPD13 GFPD15 GFPD17 GFPD19 GFPD21 GFPD23 N/C GFPVS GFPHS FPBKLP N/C N/C GND Description 18 20 22 24 26 28 30 32 34 36 38 40 42 44 ENPVDD PIN GFPD8 GFPD10 GFPD12 GFPD14 GFPD16 GFPD18 GFPD20 GFPD2
3.11 TV-Out Connector HS-2606 can support TV-Out function which input could be up to 800 x 600 graphics resolutions. World Wide Video standards are supported including NTSC-M (North America, Taiwan), NTSC-J (Japan), PAL-B, D, G, H, I (Europe, Asia), PAL-M (Brazil), PAL-N (Uruguay, Paraguay) and PAL-NC (Argentina). CN10: TV-Out Connector PIN Description PIN Description 1 3 TVCVB GND 2 4 3 1 4 GND GND 2 3.12 Ethernet Connector The HS-2606 provides one external RJ-45 interface connector.
3.13 Audio Connectors The HS-2606 has an onboard AC97 3D audio interface. The following tables list the pin assignments of the MIC In/Audio Out and Line in connectors.
3.14 PCI E-IDE Drive Connector CN13 is a standard 44-pin 2.0mm pitch connector daisy-chain driver connector serves the PCI E-IDE drive provisions onboard the HS-2606. A maximum of two ATA/33/66/100 IDE drives can be connected to the HS-2606 via CN13.
3.15 Serial Port Connectors The HS-2606 offers two W83697UF compatible UARTs with Read/Receive 16-byte FIFO serial ports and four internal 10-pin connectors.
3.16 USB Connector The HS-2606 provides two 8-pin connectors, at location J5 and J6, for four USB2.0 connections to the HS-2606. J5/J6: USB Connector PIN Description PIN Description 1 3 5 7 +5VSUS BD2-/ BD1BD2+/ BD1+ GND 2 4 6 8 +5VSUS BD3-/ BD0BD3+/ BD0+ GND 2 8 1 7 3.17 Keyboard/Mouse Connectors The HS-2606 offers CN5 for an external PS/2 type keyboard and mouse.
3.18 Watchdog Timer Once the Enable cycle is active, a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the period preset of WDT, it will assume that the program operation is abnormal. A System Reset signal will re-start when such error happens.
3.19 GPIO Connector The HS-2606 offers four general purpose I/O ports with the following capabilities: I2C/SMB Support Thermal Detect Notebook Lid Open/Close Detect Battery Low Detect J3: General Purpose Input/Output PIN Description 1 2 3 4 GPIO8 GPIO9 GPIO10 GPIO11 1 4 3.20 Mini PCI Connector HS-2606 supports a Mini PCI connector. The peripheral component with standard Type1 Mini PCI can be used.
PIN Description PIN Description 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 C/BE[3]# AD[23] GND AD[21] AD[19] GND AD[17] C/BE[2]# IRDY# 3.3V N/C SERR# GND PERR# C/BE[1]# AD[14] GND AD[12] AD[10] GND AD[8] AD[7] 3.
3.21 CompactFlash™ Connector The HS-2606 also offers an optional CompactFlash™ connector which is IDE interface located at the solder side of the board (beneath the SO-DIMM connector). The designated CN14 connector, once soldered with an adapter, can hold CompactFlash™ cards of various sizes. Please turn off the power before inserting the CD card.
3.22 PCMCIA Connector HS-2606 built-in two CardBus/PCMCIA interface connectors.
This page is intentionally left blank.
Chapter 4 AMI BIOS Setup The HS-2606 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. 4.1 Starting Setup The AMI BIOS is immediately activated when you first power on the computer.
4.2 Using Setup In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard.
4.3 Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to enter the sub-menu. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc.
4.4 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the capacity of the IDE hard disk drive is larger than 528MB, you must set the HDD mode to LBA mode. Please use the IDE Setup Utility in BIOS SETUP to install the HDD correctly. AMIBIOS SETUP – STANDARD CMOS SETUP (C)2001 American Megatrends, Inc.
4.5 Advanced CMOS Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. AMIBIOS SETUP – ADVANCED CMOS SETUP (C)2001 American Megatrends, Inc. All Rights Reserved Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Devices S.M.A.R.T.
4.6 Advanced Chipset Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system.
4.7 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. AMIBIOS SETUP – POWER MANAGEMENT SETUP (C)2001 American Megatrends, Inc.
4.8 PCI / Plug and Play Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP (C)2001 American Megatrends, Inc.
4.9 Peripheral Setup The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. PIO means Programmed Input/Output.
4.10 Auto-Detect Hard Disks This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. Up to four IDE drives can be detected, with parameters for each appearing in sequence inside a box. To accept the displayed entries, press the “Y” key; to skip to the next drive, press the “N” key. If you accept the values, the parameters will appear listed beside the drive letter on the screen. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.
4.11 Change Supervisor/User Password AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc.
PASSWORD DISABLED. When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer.
4.13 Auto Configuration with Fail Safe Settings When you press on this item you get a confirmation dialog box with a message similar to the figure below. This option allows you to load/restore the default values to your system configuration, optimizing and enabling all high performance features. Pressing ‘Y’ loads the default values that are factory settings for optimal performance system operations. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc.
4.14 Save Settings and Exit Pressing on this item asks for confirmation: AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc.
4.15 Exit Without Saving Pressing on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer. AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx (C)2001 American Megatrends, Inc.
This page is intentionally left blank.
Chapter 5 Software Utilities This chapter contains the detailed information of VGA, LAN, audio, and USB2.0 driver installation procedures. The drivers are located in the following directories of the utility disk: 5.1 VGA Driver Installation 5.1.1 VGA Driver Installation for WIN95/98/2000/XP 1. With the Utility CD Disk still in your CD ROM drive, click the chipset CLE_266.
2. Select the operating system of your computer to proceed with the installation process. 3. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next> button.
4. When the display below appears on your screen, Setup is already ready to install and copy the related files onto your hard drive. Click on the Next> button to proceed. 5. After the installation finishes, you will be prompted to restart your system. We recommend you to reboot your computer to allow the new settings to take effect. Click on the Finish button to reboot.
5.1.2 VGA Driver Installation for WIN NT4.0 1. Click the Start button on the lower left hand corner of your screen, then select Setting. Choose Control Panel and double-click on the Display icon to launch its Display Properties window. 2. Click on the Settings tab, and then choose Display Type.
3. In the Change Display Type window, click on Have Disk. 4. Specify the path of the new driver and then press on Enter.
5. Select VIA/S3G UniChrome Graphics, then click OK or press Enter. 6. You will see warning panel about Third Party Drivers. Click on Yes to finish the installation.
7. Once the installation is completed, you must shut down the system and restart for the new driver to take effect.
5.2 LAN Driver Installation 5.2.1 LAN Driver Installation for WIN95/98/2K 1. 48 With the Utility CD Disk still in your CD ROM drive, right click on My Computer icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu.
2. Select on PCI Ethernet Controller from Other devices list, right-click and then select on Properties. 3. The PCI Ethernet Controller Properties screen then appears, allowing you to reinstall the driver. Select Driver from the main menu to proceed. 4. The window then displays the current status of your LAN driver. Press on Update Driver button to continue.
5. The program will then launch the Update Device Driver Wizard window that will install your device driver. Click on the Next> button to proceed to the next step. 6. The Update Device Driver Wizard will then ask you to specify, by ticking, the path of the new driver. Tick on the open boxes where you require the program to search for the device driver then click on the Browse button to manually specify the path.
7. Update Device Driver Wizard will ask are you sure to updated driver, tick on update, and then press Next> to continue. 8. Once the program detects the device driver (*.inf) file from your specified location, it will automatically copy the files into your hard drive.
9. The program then copies the necessary files from your Windows installation disk to complete the driver setup process. Once the driver is completely installed, the following message appears on your display. Click on the Finish button to proceed. 10. Restart your computer to make the new system settings take effect. Click on the Yes button when the screen below appears and your LAN Driver for Win95 and Win98 are now completely installed.
5.2.2 LAN Driver Installation for WIN NT4.0 1. With the Utility CD Disk still in your CD ROM drive, right click on Network Neighborhood icon from the Windows menu. Select on Properties. 2. The system automatically detects the absence of Windows NT Networking. Click on the Yes button to start installation. 3. Tick on the Wired to Network once the following screen appears. Click on the Next> to proceed.
4. Click on the Start Search button for the program to locate the Network Adapter. 5. Once setup finishes the search, it will list a number of adapters for you to choose from. Press on the Have Disk button to assign the driver path location.
6. Setup now asks you for the location of the driver. When you have entered the new driver path, press on the OK button to continue. 7. When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. Press on the OK button to accept and proceed. 8. Setup then returns to Network Setup Wizard screen and displays your new Network Adapter. Click on Next> to continue.
9. The Network Setup Wizard then allows you to set the Network Protocols on your network. Select the appropriate protocol and then click on Next> to continue. 10. The Network Setup Wizard then allows you to set the Network Services on your Network, then click on Next> to continue.
11. Before Setup starts installing the components found and the settings you made, it will give you the option to proceed or go back for changes from the following screen. Click on the Next> button once you are sure of your devices. 12. Windows NT Setup will then need to copy files necessary to update the system information. Specify the path then press Continue. 13. Once it finishes copying the files, Setup will now allow you to choose the Duplex Mode of your LAN controller.
14. When Setup asks if you wish to change the TCP/IP settings of your system, select the appropriately. The default choice is No. 15. When the screen below appears, click on Next> to continue. 16. Setup then prompts you that it is ready to start the network. You may complete the installation thereafter. Click on Next> to continue.
17. Restart your computer. The LAN driver installation for WIN NT4.0 is now complete. 5.3 Audio Driver Installation 5.3.1 Audio Driver Installation for WIN98/2K/XP 1. With the Utility CD Disk still in your CD ROM drive, click the chipset “VIA_AC97”. 2. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next> button.
3. The Select Components dialog box is now displayed. Select on Install driver and then click on Next>. 4. After the audio driver installation finishes, select the Finish button to complete the installation process.
5.3.2 Audio Driver Installation for WINNT 1. With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the driver folder. 2. Press “Setup.exe” and to go setup.
3. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next> button. 4. The Select Components dialog box is now displayed. Tick on VT8233/VT8235 and then click on Next>.
5. After the audio driver installation finishes, tike restart computer now, and click the Finish button to complete the installation process.
5.4 USB2.0 Driver Installation 5.4.1 Win 98 1. Put the Utility CD Disk still in your CD ROM drive, click the “VIA 8235 USB2.0”. 2. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the “Next” button. 3. Tick on the “Install USB2.0 Driver” once the following screen appears. Click on the Next to proceed.
4. After the driver installation finishes, select restart computer now, and click the Finish button to complete the installation process.
5.4.2 Win 2000 1. With the Utility CD Disk still in your CD ROM drive, click the “VIA 8235 USB2.0”. 2. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the “Next” button.
3. When the display below appears on your screen, Setup is already ready to install and copy the related files on to your hard drive, click on the “Next” button to proceed. 4. Tick on the “Install USB2.0 Driver” once the following screen appears. Click on the Next to proceed.
5. When the Software License Agreement screen appears on your screen, press on the Next button to continue. 6. And you also can print End User Legal Agreement after your installation finished.
5.4.3 Win XP 1. With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the driver folder. 2. When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
3. The programs starts to install the USB2.0 driver when you click the Next> button on the screen below. 4. Once the InstallShield Wizard completes the operation and update of your USB2.0 driver. Click on the Yes button to restart computer to complete the installation process.
