CB60-BX/ZX Rev.
Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only.
FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
Table of Contents Chapter 1 - Introduction 1.1 Features and Specifications.................................................................................. 6 1.2 Package Checklist......................................................................................................... 10 Chapter 2 - Hardware Installation 2.1 2.2 2.3 2.4 2.5 2.6 2.7 System Board Layout ............................................................................................. System Memory................................
Appendix A - System Error Messages A.1 POST Beep....................................................................................................................... 57 A.2 Error Messages.............................................................................................................. 57 Appendix B - Troubleshooting B.1 Troubleshooting Checklist....................................................................................
Chapter 1 - Introduction 1.1 Features and Specifications 1.1.1 Features Chipset Intel 440BX AGPset (CB60-BX) Intel 440ZX AGPset (CB60-ZX) Processor The system board is equipped with Intel® Socket 370 for installing an Intel CeleronTM PPGA processor. The system board is also equipped with a switching voltage regulator that supports 1.30V to 2.05V core voltage for various processors.
Introduction DIMMs 1MBx64/x72 2MBx64/x72 4MBx64/x72 8MBx64/x72 16MBx64/x72 32MBx64/x72 Memory Size 8MB 16MB 32MB 64MB 128MB 256MB* CB60-BX * Supported only when CB60-BX uses registered DIMMs. DIMMs 1MBx64 2MBx64 4MBx64 8MBx64 16MBx64 Memory Size 8MB 16MB 32MB 64MB 128MB CB60-ZX Expansion Slots The system board is equipped with 1 dedicated AGP slot, 3 dedicated PCI slots, 2 dedicated 16-bit ISA slot and 1 shared PCI/ ISA slot. All PCI and ISA slots are bus masters.
1 Introduction PCI Bus Master IDE Controller Two PCI IDE interfaces support up to four IDE devices Ultra DMA/33 supported (Synchronous Ultra DMA mode data transfer rate up to a maximum of 33MB/sec.) PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up to 16.6MB/sec.
Introduction 1.1.3 Intelligence Automatic CPU/Chassis Fan Off The CPU and chassis fans will automatically turn off once the system enters the Suspend mode. Dual Function Power Button Depending on the setting in the BIOS setup, this switch will allow the system to enter the Soft-Off or Suspend mode. External Modem Ring-on The Modem Ring-on feature allows the system that is in the Suspend mode or Soft Power Off mode to wake-up/power-on to respond to incoming calls.
1 Introduction Important: The power button will not function once a keyboard password has been set in the KB Power On Password field of the Integrated Peripherals setup. You must type the correct password to power-on the system. The 5VSB power source of your power supply must support ≥720mA (minimum). ACPI The system board is designed to meet the ACPI (Advanced Configuration and Power Interface) specification.
Chapter 2 - Hardware Installation 2.
2 Hardware Installation CB60-ZX Note: The illustrations on the following pages are based on the CB60-BX system board, which is the board equipped with three DIMM sockets.
Hardware Installation 2.2 System Memory CB60-BX is equipped with three DIMM sockets and CB60-ZX is equipped with two DIMM sockets. 2.3 DIP Switch Settings for Processors (For Factory Use Only) The table on the next page shows the supported processors and their corresponding DIP switch settings (SW1). There are 4 switches on SW1. The black rectangle in the diagram denotes the part that is protruding, the adjustable switch.
2 Hardware Installation Processor 100MHz Frequency Ratio 4.5x 433MHz Future processor 6.5x Future processor 5x Future processor Future processor 7x 366MHz Future processor 5.5x Future processor Future processor 7.5x 400MHz Future processor 6x Future processor Future processor 8x 100MHz 300MHz Future processor 333MHz Frequency Ratio Processor 66MHz 66MHz Note: 1.
Hardware Installation Jumper JP2s settings are shown below. 1 1 1 2 2 2 3 3 3 1-2 On: Auto (default) 2-3 On: 66MHz 1-2-3 Off: 100MHz 2.5 Jumper Settings for Clearing CMOS Data Jumper JP3 Clear CMOS Data If, for some reason, the CMOS data becomes corrupted or you forgot the super visor/user/keyboard password, the system can be reconfigured with the default values stored in the ROM BIOS. To load the default values, power off your system and unplug the power cord. Set JP3 pins 2 and 3 to On.
2 Hardware Installation 2.6 Jumper Settings for Wake-On-Keyboard/ Wake-On-Mouse Jumper JP1 Wake-On-Keyboard/Wake-On-Mouse The system board supports the WakeOn-Keyboard/Wake-On-Mouse function. This function allows you to use the keyboard or mouse to power-on the system. By default, JP1 is disabled. To use this function, set JP1 to 2-3 On. Keyboard/Mouse Power On in the Integrated Peripherals setup of the Award BIOS must be set accordingly. Refer to chapter 3 for details. Warning: 1.
Hardware Installation 2.7 Connecting the Ribbon Cables and Wires of the Ports and Connectors 2.7.1 Serial Ports The built-in serial ports are RS-232C asynchronous communication ports with 16C550A-compatible UARTs that can be used with modems, serial printers, remote display terminals, and other serial devices. You can set the serial ports I/O address in the Integrated Peripherals setup of the Award BIOS. 2.7.2 PS/2 Mouse and Keyboard Ports The PS/2 mouse port uses IRQ12.
2 Hardware Installation 2.7.3 Parallel Ports The system board has a standard printer port for interfacing your PC to a parallel printer. It supports SPP, ECP and EPP modes. You can set the ports mode in the Integrated Peripherals setup of the Award BIOS. 2.7.4 Floppy Disk Controller 1. Install the 34-pin header connector into the shrouded floppy disk header (J4) on the system board. The colored edge of the ribbon should be aligned with pin 1 of J4. 2.
Hardware Installation 2.7.5 IDE Hard Disk Interface 1. If you are connecting two hard drives, install the 40-pin connector of the IDE cable into the primary shrouded IDE header (connector J10). If you are adding a third or fourth IDE device, install the 40pin connector of the other IDE cable into the secondar y shrouded IDE header (connector J9). 2. Install the other 40-pin header connector(s) into the device with the colored edge of the ribbon cable aligned with pin 1 of the drive edge connector(s).
2 Hardware Installation 2.7.6 USB Ports You must have the proper drivers installed in your operating system to use these ports. Refer to your operating systems manual or documentation. 2.7.7 IrDA Connector The system board is equipped with an IrDA connector for wireless connectivity between your computer and peripheral devices. The IRDA (Infrared Data Association) specification supports data transfers of 115K baud at a distance of 1 meter. Connect your IrDA cable to connector J12 on the system board.
Hardware Installation 2.7.8 CPU Fan Connector The processor must be kept cool by using a fan with heatsink. Connect the CPU fan to the 3-pin fan connector at location J5 on the system board. Pin Function 1 On/Off 2 +12V 3 Sense 2.7.9 Chassis Fan Connector The system board is equipped with a chassis fan connector. If you are installing a fan in the system unit, connect the fans connector to location J2 on the system board.
2 Hardware Installation 2.7.10 AGP Fan Connector The system board is equipped with an AGP fan connector. If the system board is installed with an AGP add-in card and you wish to install a fan on the add-in card, connect the fans connector to location J11 on the system board. Refer to the add-in cards manual for instructions on installing the fan. Pin Function 1 Ground 2 +12V 3 N. C. 2.7.
Hardware Installation 2.7.12 Wake-On-LAN Connector The system board supports the Wake-On-LAN function. This function will allow the network to remotely power-on a Soft Power Down (Soft-Off) PC. However, if your system is in the Suspend mode, you can power-on the system only through an IRQ or DMA interrupt. To use the Wake-On-LAN function, you must enable the Resume on LAN field in the Power Management Setup of the Award BIOS. Your LAN card package should include a cable.
2 Hardware Installation 2.7.13 Power Connector PS1 The pin assignment of the ATX power connector is shown below. Pin Function Pin Function 1 3.3V/14A 11 3.3V/14A 2 3.3V/14A 12 -12V 3 COM 13 COM 4 +5V 14 PS-ON 5 COM 15 COM 6 +5V 16 COM 7 COM 17 COM 8 PW-OK 18 -5V 9 5VSB 19 +5V 10 +12V 20 +5V Important: Your power supply must meet the ATX specification supporting 3.3V/14A (minimum), otherwise your system will not boot properly.
Hardware Installation 2.7.14 J14 (LEDs and Switches) HD-LED: Primary/Secondary IDE LED This LED will light when the hard drive is being accessed. G-LED: Green LED This LED will light when the system is in the Suspend mode. ATX-SW: ATX Power Switch Depending on the setting in the BIOS setup, this switch is a dual function power button that will allow your system to enter the SoftOff or Suspend mode. Refer to Soft-Off By PWR-BTTN in the Power Management Setup (Chapter 3).
2 Hardware Installation KEYLOCK: Power/Standby LED and Keylock Connector Use pins 21-23 to connect to the Power/Standby LED. This LED will light when the systems power is on and blinks when the system enters the Suspend mode. Use pins 24 to 25 to connect to the keyboard lock (located on the front panel of the system chassis) for locking the keyboard.
Chapter 3 - Award BIOS Setup Utility 3.1 The Basic Input/Output System The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and peripherals. In addition, the BIOS also contain codes for various advanced features found in this system board. This chapter explains the Setup Utility for the Award BIOS. After you power up your system, the BIOS message appears on your screen and the memory count begins.
3 Award BIOS Setup Utility ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Mon, Oct 12 1998 Time (hh:mm:ss) : 13: 27: 50 HARD DISKS Primary Master : Primary Slave : Secondary Master : Secondary Slave : TYPE SIZE CYLS HEAD Auto 0 0 0 Auto 0 0 0 Auto 0 0 0 Auto 0 0 0 PRECOMP LANDZ SECTOR MODE 0 0 0 Auto 0 0 0 Auto 0 0 0 Auto 0 0 0 Auto Drive A : 1.44M, 3.5 in.
Award BIOS Setup Utility Drive A and Drive B These categories identify the types of floppy disk drives installed. None 360K, 5.25 in. 1.2M, 5.25 in. 720K, 3.5 in. 1.44M, 3.5 in. 2.88M, 3.5 in. No floppy drive is installed 5-1/4 in. standard drive; 360KB capacity 5-1/4 in. AT-type high-density drive; 1.2MB capacity 3-1/2 in. double-sided drive; 720KB capacity 3-1/2 in. double-sided drive; 1.44MB capacity 3-1/2 in. double-sided drive; 2.
3 Award BIOS Setup Utility 3.1.2 BIOS Features Setup The BIOS Features Setup allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. ROM PCI/ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE, INC.
Award BIOS Setup Utility CPU L1 Cache and CPU L2 Cache These categories speed up the memory access. The default value is enabled. Enable the External Cache for better performance. CPU L2 Cache ECC Checking Intel CeleronTM processor comes with built-in Level 2 cache. By default, ECC is enabled to check the Level 2 cache. If you are not using this function, set this field to Disabled. Quick Power On Self Test This category speeds up Power On Self Test (POST) after you power on your system.
3 Award BIOS Setup Utility Boot Up NumLock Status This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys. Typematic Rate Setting When disabled, continually holding down a key on your keyboard will cause the BIOS to report that the key is down.
Award BIOS Setup Utility OS Select for DRAM > 64MB This item allows you to access the memor y that is over 64MB in OS/2. The options are: Non-OS/2 and OS/2. HDD S.M.A.R.T. Capability The system board supports SMART (Self-Monitoring, Analysis and Reporting Technology) hard drives. SMART is a reliability prediction technology for ATA/IDE and SCSI drives. The drive will provide sufficient notice to the system or user to backup data prior to the drives failure. The default is Disabled.
3 Award BIOS Setup Utility SDRAM RAS-to-CAS Delay This field allows you to insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. This field applies only when synchronous DRAM is installed in the system. SDRAM RAS Precharge Time If there is insufficient number of cycles for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain data.
Award BIOS Setup Utility Video RAM Cacheable When enabled, it allows the video RAM to be cacheable thus providing better video performance. If your graphics card does not support this function, leave this field in its default setting - Disabled. 8 Bit I/O Recovery Time and 16 Bit I/O Recovery Time The recovery time is the length of time, measured in SYSCLK, which the system will delay after the completion of an input/output request.
3 Award BIOS Setup Utility Regardless of the type of processor used, the default setting is Default. Under this setting, the system will run at 66MHz or 100MHz depending on the processors clock frequency. If you selected an option other than Default and is unable to boot up the system, there are 2 methods of going back to its default setting. Method 1: Clear the CMOS data by following the procedure in section 2.5 (chapter 2) of this manual.
Award BIOS Setup Utility Current System Temperature, Current CPU Temperature, Current Chassis Fan Speed and Current CPU Fan Speed These fields show the internal temperature of the system, current temperature of the processor, and the current fan speed of the chassis and CPU fans in RPM (Revolutions Per Minute). CPU(V) This field shows the voltage of the processor. +1.5V, +3.3V, +5V, +12V, -12V and -5V These fields show the output voltage of the power supply. 3.1.
3 Award BIOS Setup Utility ACPI Function By default, the ACPI function is disabled. This function should be enabled only in operating systems that support ACPI. Power Management This category allows you to select the type (or degree) of power saving by changing the length of idle time that elapses before the Standby mode and Suspend mode are activated. Disable No power management. Disables the Standby and Suspend modes. Min. Power Saving Minimum power management. Standby Mode = 1 hr.
Award BIOS Setup Utility Video Off After N/A The system BIOS will never turn off the screen. Suspend The screen is off when the system is in the Suspend mode. Standby The screen is off when the system is in the Standby mode. MODEM Use IRQ This category is used to set an IRQ channel (IRQ 3, 4, 5, 7, 9, 10 or 11) for the external modem installed in your system. However, if the Resume on Ring or Resume on LAN field is disabled, the BIOS will mask the IRQ assigned for the modem.
3 Award BIOS Setup Utility Soft-Off by PWR-BTTN This category allows you to select the method of powering off your system. Hold 4 Sec. Regardless of whether the Power Management field is enabled or disabled, if the power button is pushed and released in less than 4 sec, the system enters the Suspend mode. The purpose of this function is to prevent the system from powering off in case you accidentally hit or pushed the power button. Push and release again in less than 4 sec to restore.
Award BIOS Setup Utility 7. Press to return to the main menu of the Award BIOS setup utility. Select Save & Exit Setup and press . 8. Type and press . Resume On LAN With a LAN card installed, the Wake-On-LAN function allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. However, if your system is in the Suspend mode, you can wakeup the system only through an IRQ or DMA interrupt. Make sure your LAN card supports the remote wakeup function.
3 Award BIOS Setup Utility 3.1.5 PNP/PCI Configuration This section describes configuring the PCI bus system. It covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. ROM PCI/ISA BIOS PNP/PCI CONFIGURATION AWARD SOFTWARE, INC.
Award BIOS Setup Utility Assign IRQ for VGA When Enabled, the system automatically assigns an IRQ for the VGA card installed. Your VGA card will need an IRQ only when using the video capture function of the card. If you are not using this function and a new device requires an IRQ, you can set this function to Disabled. The IRQ (previously occupied by the VGA card) will be available for your new device. Note: When Disabled, a Yellow mark will appear in Windows 95s Device Manager.
3 Award BIOS Setup Utility 3.1.7 Load Optimal Settings The Load Optimal Settings option loads optimized settings from the BIOS ROM. Use the Setup default values as standard values for your system. Highlight this option on the main menu and press . The message below will appear. Load Optimal Settings (Y/N)? N Type and press to load the Setup default values. 3.1.8 Integrated Peripherals ROM PCI/ISA BIOS INTEGRATED PERIPHERALS AWARD SOFTWARE, INC.
Award BIOS Setup Utility themselves. Your system supports five modes, 0 (default) to 4, which primarily differ in timing. When Auto is selected, the BIOS will select the best available mode after checking your drive. Auto The BIOS will automatically set the system according to your hard disk drives timing. 0-4 You can select a mode that matches your hard disk drives timing. Caution: Do not use the wrong setting or you will have drive errors.
3 Award BIOS Setup Utility Onboard FDC Controller Enabled Enables the onboard floppy disk controller. Disabled Disables the onboard floppy disk controller. Onboard Serial Port 1 and Onboard Serial Port 2 Auto The system will automatically select an I/O address for the onboard serial port 1 and serial port 2. 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3 Allows you to manually select an I/O address for the onboard serial port 1 and serial port 2. Disabled Disables the onboard serial port 1 and/or serial port 2.
Award BIOS Setup Utility Parallel Port Mode, ECP Mode Use DMA and EPP Mode Select These fields will appear only if you selected an I/O address and IRQ in the Onboard Parallel Por t field. These apply to a standard specification and will depend on the type and speed of your device. Refer to your peripherals manual for the best option. The parallel modes are SPP, EPP, ECP and ECP+EPP. The default is ECP+EPP. Both ECP Mode Use DMA and EPP Mode Select will appear on the screen.
3 Award BIOS Setup Utility Hot Key When this option is selected, the KB Power On Hot Key field will appear. Move the cursor to this field to select a function key you would like to use to poweron the system. The options are from Ctrl-F1 to CtrlF12. Mouse Left When this option is selected, double-click the left button of the mouse to power-on the system. Mouse Right When this option is selected, double-click the right button of the mouse to power-on the system.
Award BIOS Setup Utility 3.1.10 User Password If you want another user to have access only to your system but not to setup, set a users password with the System option selected in the BIOS Features Setup. If you want a user to enter a password when trying to access setup, set a users password with the Setup option selected in the BIOS Features Setup. Using users password to enter Setup allows a user to access only the User Password option that appears on the main screen.
3 Award BIOS Setup Utility 3.1.12 Save & Exit Setup When all the changes have been made, highlight Save & Exit Setup and press . The message below will appear: Save to CMOS and Exit (Y/N)? N Type Y and press . The modifications you have made will be written into the CMOS memory, and the system will reboot. You will once again see the initial diagnostics on the screen.
Chapter 4 - Supported Softwares 4.1 Desktop Management Interface (DMI) The system board comes with a DMI built into the BIOS. DMI, along with the appropriately networked software, is designed to make inventory, maintenance and troubleshooting of computer systems easier. With DMI, a network administrator or MIS engineer can remotely access some information about a particular computer system without physically going to it. Quite often a service call may be unnecessary as the problem can be solved remotely.
Supported Softwares 4.1.
Supported Softwares Add DMI 1. Use the ← or → arrow keys to select the Add DMI menu. 2. Highlight the item on the left screen that you would like to add by using the ↑ or ↓ arrow keys, then press . 3. The cursor will move to the screen you select allowing you to enter information about the added item. 4. Press to save information into the flash ROM. To view information about the added items, go to the Edit DMI menu. Load DMI File 1. Use the ← or → arrow keys to select the Load DMI File menu.
4 Supported Softwares 4.2 Hardware Doctor Utility The system board comes with a Hardware Doctor utility contained in the provided CD. This utility is capable of monitoring the systems health conditions and allows you to manually set a range (Highest and Lowest Limit) to the items being monitored. If the settings/ values are over or under the set range, a warning message will popup. The utility can also be configured so that a beeping alarm will sound whenever an error occurs.
Supported Softwares settings of the Voltages. Make sure to leave them in their default setting. To further configure the utility, select Configuration in the Tools menu. The Monitoring Config. screen will appear. (Click here for a clearer view of the screen) Enable Click on the items you want to be monitored. Faults Count (1 or 3) This allows you to select the number of fault counts detected before a warning message pop-up. "1" = The warning message will pop-up once an error has been detected.
4 Supported Softwares enabled is System Temp. If the internal temperature of the system is too high, only a warning message will pop-up. Temperature Unit You can select the temperature unit between Celsius and Fahrenheit. The default unit is Celsius. Polling Interval This is used to set the interval for monitoring the system. The range is from 1 sec. to 120 sec. The default interval is 2 sec. 4.3 Patch Utility for Windows 95 The CD included in the system board package contains a patch utility.
Appendix A - System Error Message When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in the information box at the bottom. Enter Setup to correct the error. A.1 POST Beep There are two kinds of beep codes in the BIOS.
A System Error Message setting than indicated in Setup. Determine which setting is correct, either turn off the system and change the jumper or enter Setup and change the VIDEO selection. FLOPPY DISK(S) fail (80) Unable to reset floppy subsystem. FLOPPY DISK(S) fail (40) Floppy type mismatch. Hard Disk(s) fail (80) HDD reset failed. Hard Disk(s) fail (40) HDD controller diagnostics failed. Hard Disk(s) fail (20) HDD initialization error. Hard Disk(s) fail (10) Unable to recalibrate fixed disk.
Appendix B - Troubleshooting B.1 Troubleshooting Checklist This chapter of the manual is designed to help you with problems that you may encounter with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple causes. Some of the most common things to check when you encounter problems while using your system are listed below. 1.
B Troubleshooting The picture seems to be constantly moving. 1. The monitor has lost its vertical sync. Adjust the monitors vertical sync. 2. Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display. 3. Make sure your video cards output frequencies are supported by this monitor. The screen seems to be constantly wavering. 1. If the monitor is close to another monitor, the adjacent monitor may need to be turned off.
Troubleshooting Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootable (first) hard drive is configured as Master and the second hard drive is configured as Slave. The master hard drive must have an active/bootable partition. Excessively long formatting period. 1.
B Troubleshooting Serial Port The serial device (modem, printer) doesnt output anything or is outputting garbled characters. 1. Make sure that the serial devices power is turned on and that the device is on-line. 2. Verify that the device is plugged into the correct serial port on the rear of the computer. 3. Verify that the attached serial device works by attaching it to a serial port that is working and configured correctly.
