IB865 LGA775 Pentium 4 Intel 865G Chipset Full Size CPU Card USER’S MANUAL Version 1.
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction....................................................... 1 Checklist .......................................................................... 1 Product Description .......................................................... 2 Specifications ................................................................... 3 Board Dimensions............................................................. 4 Installations.......................................................
ATTENTION: It is strongly recommended that only heatsinks that have corresponding (metal) backplates are used on the CPU card. This is to avoid the CPU card being bent/distorted, causing the CPU card to become damaged. A reference picture of a backplate and heatsink that has backplate are shown below.
INTRODUCTION Introduction Checklist Your IB865 Pentium 4 CPU card package should include the items listed below: • The IB865 CPU Card • This User’s Manual • 1 IDE Ribbon Cable • 1 Floppy Ribbon Connector • SATA Power Cord • SATA Cable • 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a Mounting Bracket • 1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse • 1 CD containing the following: • Chipset Drivers • Flash Memory Utility • Optional audio cable with bracket (Audio8K) • Optional USB cable
INSTALLATIONS Product Description The IB865 Pentium 4 CPU card incorporates the Intel 865G chipset that can utilize a LGA775 processor of up to 3.8GHz or higher and supports FSB frequency of 533/800Mhz (133Mhz, and 200Mhz HCLK respectively). The 865G chipset comes with a Graphics Memory Controller Hub (GMCH) designed for use with the Pentium 4 processor with 1MB L2 cache on 0.09 micron process.
INTRODUCTION Specifications Product Name CPU Type CPU Voltage System Speed CPU Operating Frequency Green /APM CPU Socket Chipset BIOS Cache MicroAGP Socket VGA Primary LAN Secondary LAN Audio Memory type LPC I/O RTC/CMOS Local bus IDE Serial ATA D-type Connectors Power Connector PCI to ISA Bridge ISA High Drive USB Watchdog Timer System Voltages Other Features Form Factor Board Size IB865 LGA775 socket (Intel Pentium 4 / Celeron D) 0.8375V~1.6V (VRD 10.1) 2.53GHz~3.8GHz 533MHz/800MHz APM1.
INSTALLATIONS Board Dimensions 4 IB865 User’s Manual
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB865 in order to set up a workable system. The topics covered are: Installing the CPU ............................................................ 6 ATX Power Installation .................................................... 7 Installing the Memory....................................................... 7 Setting the Jumpers...........................................................
INSTALLATIONS Installing the CPU The IB865 CPU card supports a LGA 775 processor socket for Intel® Pentium® 4 processors. The LGA 775 processor socket comes with a lever to secure the processor. Refer to the pictures below, from left to right, on how to place the processor into the CPU socket. Please note that the cover of the LGA775 socket must always be installed during transport to avoid damage to the socket.
INSTALLATIONS ATX Power Installation The system power is provided to the CPU card with the CN1 and J7 ATX power connectors. Please note that the J7 external ATX power connector should be connected to the backplane for IB865 to function. J7 is a 3-pin power connector. CN1 is a 4-pin 12V power connector. CN1 is to be connected to the ATX power supply. Installing the Memory The IB865 CPU card supports two DDR memory sockets for a maximum total memory of 2GB in DDR memory type.
INSTALLATIONS Setting the Jumpers Jumpers are used on IB865 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB865 and their respective functions. Jumper Locations on IB865..........................................................9 JP1: Clear CMOS Contents........................................................
INSTALLATIONS Jumper Locations on IB865 JP1: Clear CMOS Contents JP2, JP3, JP4: RS232/422/485 (COM2) Selection JP5/6/7/8/9/10/11: CRT VGA Signal Select JP13: Primary LAN Enable/Disable JP14: DiskOnChip Address Select Jumper Locations on IB865 IB865 User’s Manual 9
INSTALLATIONS JP1: Clear CMOS Contents Use JP1, a 3-pin header, to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the CPU card before clearing CMOS. JP1 Setting Function Pin 1-2 Short/Closed Normal Pin 2-3 Short/Closed Clear CMOS JP2, JP3, JP4: RS232/422/485 (COM2) Selection J4, COM1 is fixed for RS-232 use only. J5, COM2 is selectable for RS232, RS-422 and RS-485. The following table describes the jumper settings for COM2 selection.
INSTALLATIONS JP13: Primary LAN Enable/Disable JP13 Function Enable LAN Disable LAN JP14: DiskOnChip Address Select JP14 Address D0000-D7FFF D8000-DFFFF (default) IB865 User’s Manual 11
INSTALLATIONS Jumper and Connectors on IBA120 J1: Panel Inverter Power Connector Pin # Signal Name 1 +12V 2 ENABKL 3 Ground Remarks: Maximum current is 1A. JP2: Panel Voltage Setting JP2 Setting Panel Voltage Pin 1-2 Short/Closed 3.
INSTALLATIONS JP1: TV Type Select JP1 Setting TV Type Pin 1-2 Short/Closed NTSC Pin 2-3 Short/Closed PAL JP2: LVDS Panel Power Select JP2 Setting Panel Voltage Pin 1-2 Short/Closed 3.3V (default) Pin 2-3 Short/Closed 5V J2, J3: LVDS Connectors (2nd channel, 1st channel) The LVDS connectors, DF13 20-pin mating connectors, are composed of the first channel (J2) and second channel (J3) to support 24-bit or 48-bit.
INSTALLATIONS Jumper and Connectors on IBA110 J1: TMDS Panel Connector TMDS stands Transition Minimized Differential Signaling. J1 Signal Name TX1P TXIN GND GND TXCP TXCN GND +5v HTPG NC Pin # 1 2 3 4 5 6 7 8 9 10 Pin # 11 12 13 14 15 16 17 18 19 20 Signal Name TX2P TX2N GND GND TX0P TX0N NC NC DDCDATA DDCCLK J2: CRT2 / TV-Out Connector This connector is used for a second CRT monitor or use with a TV output device. J2 14 Signal Name Red / C Green / Y Blue / COMP N.C.
INSTALLATIONS J3: Panel Inverter Power Connector The connector supports 1A current (maximum). Pin # 1 2 3 Signal Name +12V NC Ground J4: VGA Chipset Fan Power Connector Pin # 1 2 Signal Name +12V Ground J5, J6: LVDS Connectors (2nd channel, 1st channel) The LVDS connectors, DF13 20-pin mating connectors, are composed of the first channel (J6) and second channel (J5) to support 24-bit or 48-bit. Signal Name Pin # Pin # Signal Name TX02 1 TX0+ Ground 4 3 Ground TX16 5 TX1+ 5V/3.
INSTALLATIONS SW1: LVDS Resolution Select SW1-1 OFF ON OFF 16 SW1-2 ON OFF OFF SW1-3 ON ON ON Resolution 800x600 18 bit 1024x768 18bit 1024x768 24 bit IB865 User’s Manual
INSTALLATIONS [ Connectors on IB865 The connectors on IB865 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on IB865 and their respective functions. Connector Locations on IB865 .................................................. 18 IDE1, IDE2: EIDE Connectors.................................................. 20 FDD1: Floppy Drive Connector.................................................
INSTALLATIONS Connector Locations on IB865 Connector Locations on IB865: IDE1, IDE2: EIDE Connectors FDD1: Floppy Drive Connector CN1: ATX 12V/+12V Power Connector CN2, CN3: USB Connectors J3: CPU Fan Power Connector J7: External ATX Power Connector J8, J9: System Fan Power Connector J1: System Function Connector J2: Parallel Port Connector J4, J5: COM1 and COM2 Serial Ports Connector J10: Wake On LAN Connector J11: External Audio Connector J12: CD-In Audio Connector J13, J14: Serial ATA (SATA) Connectors
INSTALLATIONS IDE1, IDE2: EIDE Connectors Signal Name Pin # Reset IDE 1 Host data 7 3 Host data 6 5 Host data 5 7 Host data 4 9 Host data 3 11 Host data 2 13 Host data 1 15 Host data 0 17 Ground 19 DRQ0 21 Host IOW 23 Host IOR 25 IOCHRDY 27 DACK0 29 IRQ14 31 Address 1 33 IDE1 Address 0 35 Chip select 0 37 Activity 39 IDE2 Signal Name Reset IDE Host data 7 Host data 6 Host data 5 Host data 4 Host data 3 Host data 2 Host data 1 Host data 0 Ground DRQ1 Host IOW Host IOR IOCHRDY DACK1 IRQ15 Address 1 Address
INSTALLATIONS FDD1: Floppy Drive Connector FDD1 is a 34-pin header and will support up to 2.88MB floppy drives.
INSTALLATIONS CN2, CN3: USB Connectors The following table shows the pin outs of the USB pin headers connectors. Overall, the two pin headers support four USB ports. CN2 Signal Name Vcc USB0USB0+ Ground Pin 1 2 3 4 Pin 5 6 7 8 Signal Name Ground USB1+ USB1Vcc CN3 Signal Name Vcc USB2USB2+ Ground Pin 1 2 3 4 Pin 5 6 7 8 Signal Name Ground USB3+ USB3Vcc J3: CPU Fan Power Connector J3 is a 3-pin header for the CPU fan. The fan must be a 12V fan.
INSTALLATIONS J1: System Function Connector J1 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. J1 is a 20-pin header that provides interfaces for the following functions. Hard Disk Drive LED Reset Switch Not Defined ATX Power On Switch SMI / Hardware Switch Power LED Speaker Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended.
INSTALLATIONS SMI/Hardware Switch: Pins 6 and 16 This connector supports the "Green Switch" on the control panel, which, when pressed, will force the system into the power-saving mode immediately. Pin # 6 Signal Name SMI 16 Ground ATX Power ON Switch: Pins 7 and 17 This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on.
INSTALLATIONS J2: Parallel Port Connector The following table describes the pin out assignments of this connector.
INSTALLATIONS J10: Wake On LAN Connector J10 is a 3-pin header for the Wake On LAN function on the motherboard. The following table shows the pin out assignments of this connector. Wake On LAN will function properly only with an ATX power supply with 5VSB that has 1A. Pin # Signal Name 1 +5VSB 2 Ground 3 LAN Wakeup J11: External Audio Connector J11 is a 12-pin header that is used to connect to the optional audio cable that integrates jacks for Line In, Line Out and Mic.
INSTALLATIONS J15: VGA CRT Connector The pin assignments of the J15 VGA CRT connector are as follows: J15 Signal Name Red Blue GND GND N.C. N.C. HSYNC NC Pin 1 3 5 7 9 11 13 15 Pin 2 4 6 8 10 12 14 Signal Name Green N.C. GND GND GND N.C. VSYNC J16, J18: External PS/2 Keyboard and Mouse Connector Pin # 1 2 3 4 5 J16 KB clock KB data N.C. Ground Vcc J18 Mouse data N.C. Ground Vcc Mouse clock J17: IrDA Connector J17 is used for an optional IrDA connector for wireless communication.
INSTALLATIONS J19: PS/2 Keyboard and Mouse Connector J19 uses a Y-cable with dual D-connectors for a PS/2 keyboard and a PS/2 mouse. J19 Pin # 1 2 3 4 5 6 Signal Name Mouse data Keyboard data Ground Vcc Mouse Clock Keyboard Clock J20: Primary RJ45 Connector J20 is the primary RJ-45 connector based on the chipset integrated LAN. The figure below shows the pin out assignments of the connector and its corresponding input jack. J21: Gigabit LAN RJ45 Connector J21 is the Gigabit LAN RJ45 connector.
INSTALLATIONS Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sort of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
INSTALLATIONS mov al, 01h mov cl, 30h call Write_Reg ;watchdog enabled call Lock_Chip ret Enable_And_Set_Watchdog Endp ;[]=============================================== ; Name : Disable_Watchdog ; IN : None ; OUT : None ;[]=============================================== Disable_Watchdog Proc Near call Unlock_Chip mov cl, 07h mov al, 08h call Write_Reg ;switch to LD8 xor al, al mov cl, 0F6h call Write_Reg ;clear watchdog timer xor al, al mov cl, 30h call Write_Reg ;watchdog disabled call Lock_Chip
INSTALLATIONS ; Name : Lock_Chip ; IN : None ; OUT : None ;[]================================================ Unlock_Chip Proc Near mov dx, 2Eh mov al, 0AAh out dx, al ret Unlock_Chip Endp ;[]================================================ ; Name : Write_Reg ; IN : CL - register index ; AL - Value to write ; OUT : None ;[]================================================ Write_Reg Proc Near push ax mov dx, 2Eh mov al,cl out dx,al pop ax inc dx out dx,al ret Write_Reg Endp ;[]===============================
BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the CPU card. The topics covered in this chapter are as follows: BIOS Introduction................................................................... 32 BIOS Setup ............................................................................. 32 Standard CMOS Setup ........................................................... 34 Advanced BIOS Features ...............................................
BIOS SETUP BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium 4 processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ESC : Quit F10 : Save & Exit Setup á â à ß : Select Item Time, Date, Hard Disk Type… The section below the setup items of the Main Menu display
BIOS SETUP Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the CPU card is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
BIOS SETUP Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the / or +/- keys to set the current time. IDE Primary HDDs / IDE Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. Each channel can support up to two hard disks; the first is the “Master” and the second is the “Slave”.
BIOS SETUP Video This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt On This field determines whether or not the system will halt if an error is detected during power up. No errors The system boot will not be halted for any error that may be detected.
BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP Hyper-Threading Technology This feature is enabled when your processor supports Hyper-Threading Technology. Otherwise, this field will be hidden. Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items. First/Second/Third Boot Device These fields determine the drive that the system searches first for an operating system.
BIOS SETUP Typematic Rate (Chars/Sec) When the typematic rate is enabled, the system registers repeated keystrokes speeds. Settings are from 6 to 30 characters per second. Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. Security Option This field allows you to limit access to the System and Setup. The default value is Setup.
BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset.
BIOS SETUP DRAM RAS# Precharge This option sets the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes. The default setting for the Active to Precharge Delay is 3. Memory Frequency For This field sets the frequency of the DRAM memory installed. The default setting is Auto. The other settings are PC200 and PC266. System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h-FFFFFh, resulting in better system performance.
BIOS SETUP On-Chip VGA By default, the On-Chip VGA or 865G chipset-integrated VGA is Enabled. On-Chip Frame Buffer Size The On-Chip Frame Buffer Size can be set us 1MB, 8MB or 16MB. This memory is shared with the system memory. Boot Display Boot Display determines the display output device where the system boots. The default setting is LVDS. Panel Scaling With the default setting of Auto, this item automatically displays the resolution of the panel used in the system to ‘full’ screen.
BIOS SETUP Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main items for user to select. Once an item selected, a submenu appears. Details follow.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility SuperIO Device Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select Onboard Parallel Port Parallel Port Mode Power After PWR-Fail Enabled 3F8/IRQ4 2F8/IRQ3 Normal 378/IRQ7 SPP off ITEM HELP Menu Level IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive.
BIOS SETUP USB Keyboard Support By default, this field is set to Disabled. USB Mouse Support By default, this field is set to Disabled. AC97 Audio The default setting of the AC97 Audio is Auto. CSA LAN (Giga-LAN) The default setting of the onboard Gigabit LAN is enabled. Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the CPU card and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
BIOS SETUP Power Management Setup The Power Management Setup allows you to save energy of your system effectively.
BIOS SETUP Power Management This field allows you to select the type of power saving management modes. There are four selections for Power Management. Min. Power Saving Minimum power management Max. Power Saving Maximum power management. User Define Each of the ranges is from 1 min. to 1hr. Except for HDD Power Down which ranges from 1 min. to 15 min. Video Off Method This field defines the Video Off features. There are three options.
BIOS SETUP CPU THRM-Throttling When the system enters Doze mode, the CPU clock runs only part of the time. You may select the percent of time that the clock runs. Wake-Up by PCI Cards Enable this field to allow wake up function through a PCI card. Power On by Ring This field enables or disables the power on of the system through the modem connected to the serial port or LAN. Wake Up On CSA Lan Enable this field to allow wake up function through the onboard CSA LAN.
BIOS SETUP PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. Phoenix - AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature Current SystemTemp. Current CPU Temp. Current System Temp.
BIOS SETUP Frequency/Voltage Control This section shows the user how to configure the processor frequency. Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI Clk Disabled Spread Spectrum Disabled ITEM HELP Menu Level Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock. Spread Spectrum This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only.
BIOS SETUP Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. Load Setup Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. Set Supervisor/User Password These two options set the system password.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98, Windows NT 4.0 and Windows 2000. The software and drivers are included with the CPU card. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel 865G Chipset Software Intallation Utility................ 54 Intel 865G Chipset Graphics Driver ................................
DRIVERS INSTALLATION Intel 865G Chipset Software Intallation Utility The Intel 865G Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 98/98SE/ME/2000/XP. 1. Insert the CD that comes with the CPU card and the screen below would appear. Click Intel Chipsets and then Intel 865G Chipset Family Drivers. 2.
DRIVERS INSTALLATION 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to accept the software license agreement and proceed with the installation process.
DRIVERS INSTALLATION 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVERS INSTALLATION Intel 865G Chipset Graphics Driver The Intel 865G Chipset Family Graphics Drivers come in the CD with the CPU card . Follow the instructions below to complete the installation under Windows 98/98SE/ME/2000/XP. 1. Insert the CD that comes with the CPU card and the screen below would appear. Click Intel Chipsets and then Intel 865G Chipset Family Drivers. 2. When the Welcome screen appears, click Next to continue.
DRIVERS INSTALLATION 3. Click Yes to accept the software license agreement and proceed with the installation process. 4. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVERS INSTALLATION Realtek AC97 Codec Audio Driver Installation Follow the steps below to install the Realtek AC97 Codec Audio Drivers. 1. Insert the CD that comes with the CPU card and the screen below would appear. Click Intel Chipsets, then Intel 865G Chipset Family Drivers. Click Realtek AC97 Codec Audio Drivers to start installation. 2. Click Finish to restart the computer and for changes to take effect. .
DRIVERS INSTALLATION Intel PRO LAN Drivers Installation The Intel PRO LAN drivers support both Intel® PRO/100 and PRO/1000 drivers. Follow the steps below to complete the installation. 1. Insert the CD that comes with the CPU card and the screen below would appear. Click on LAN Card on the left side to make the LAN drivers selection. Click on Intel(R) PRO LAN Drivers. 2. Click Install Now. 3. Click Restart to restart the computer and new settings to take effect.
