Datasheet

PCI Express* Configuration Registers
482 Intel® Xeon® Processor D-1500 Product Family
Datasheet - Volume 1 of 4: Integrated Platform Controller Hub
March 2015
13.1.4 PCISTS—PCI Status Register (PCI Express*—D28:F0/F1/
F2/F3/F4/F5/F6/F7)
Address Offset: 06h–07h Attribute: R/WC, RO
Default Value: 0010h Size: 16 bits
2 Bus Master Enable (BME) — R/W.
0 = Disable. Memory and I/O requests received at a Root Port must be handled as Unsupported
Requests.
1 = Enable. Allows the root port to forward Memory and I/O Read/Write cycles onto the backbone
from a PCI Express* device.
Note: This bit does not affect forwarding of completions in either upstream or downstream direction
nor controls forwarding of requests other than memory or I/O
1 Memory Space Enable (MSE) — R/W.
0 = Disable. Memory cycles within the range specified by the memory base and limit registers are
master aborted on the backbone.
1 = Enable. Allows memory cycles within the range specified by the memory base and limit registers
can be forwarded to the PCI Express device.
0 I/O Space Enable (IOSE) — R/W. This bit controls access to the I/O space registers.
0 = Disable. I/O cycles within the range specified by the I/O base and limit registers are master
aborted on the backbone.
1 = Enable. Allows I/O cycles within the range specified by the I/O base and limit registers can be
forwarded to the PCI Express device.
Bit Description
Bit Description
15 Detected Parity Error (DPE) — R/WC.
0 = No parity error detected.
1 = Set when the root port receives a command or data from the backbone with a parity error. This
is set even if PCIMD.PER (D28:F0/F1/F2/F3:04, bit 6) is not set.
14 Signaled System Error (SSE) — R/WC.
0 = No system error signaled.
1 = Set when the root port signals a system error to the internal SERR# logic.
13 Received Master Abort (RMA) — R/WC.
0 = Root port has not received a completion with unsupported request status from the backbone.
1 = Set when the root port receives a completion with unsupported request status from the
backbone.
12 Received Target Abort (RTA) — R/WC.
0 = Root port has not received a completion with completer abort from the backbone.
1 = Set when the root port receives a completion with completer abort from the backbone.
11 Signaled Target Abort (STA) — R/WC.
0 = No target abort received.
1 = Set whenever the root port forwards a target abort received from the downstream device onto
the backbone.
10:9 DEVSEL# Timing Status (DEV_STS) — Reserved per the PCI Express* Base Specification.
8 Master Data Parity Error Detected (DPED) — R/WC.
0 = No data parity error received.
1 = Set when the root port receives a completion with a data parity error on the backbone and
PCIMD.PER (D28:F0/F1/F2/F3:04, bit 6) is set.
7 Fast Back to Back Capable (FB2BC) — Reserved per the PCI Express* Base Specification.
6 Reserved
5 66 MHz Capable — Reserved per the PCI Express* Base Specification.
4 Capabilities List — RO. Hardwired to 1. Indicates the presence of a capabilities list.
3 Interrupt Status — RO. Indicates status of Hot-Plug and power management interrupts on the root
port that result in INTx# message generation.
0 = Interrupt is de-asserted.
1 = Interrupt is asserted.
This bit is not set if MSI is enabled. If MSI is not enabled, this bit is set regardless of the state of
PCICMD.Interrupt Disable bit (D28:F0/F1/F2/F3/F4/F5/F6/F7/F6/F7:04h:bit 10).
2:0 Reserved