Guide
Mechanical Drawings
Intel® Xeon® Processor E7 2800/4800/8800 v2 Product Family 105
Thermal/ Mechanical Specifications and Design Guide
Figure G-14. Processor 4U Heatsink Stiffener Mechanical Drawing - G45952 Rev C
13
4
5678
B
C
D
A
123
4
5678
B
C
D
A
2200 MISSION COLLEGE BLVD.
P.O. BOX 58119
SANTA CLARA, CA 95052-8119
R
10
94.75
70
1.2
4.5
3
6.75
36
G45952 1 C
DWG. NO SHT. REV
SHEET 1 OF 1
DO NOT SCALE DRAWING
SCALE: 1:1
CG45952D
REV
DRAWING NUMBER
SIZE
BRICKLAND EX HSINK STIFFENER
TITLE
PTMI
DEPARTMENT
SEE NOTESSEE NOTES
FINISHMATERIAL
--
DATEAPPROVED BY
--
--
DATECHECKED BY
9/21/11T. BOYD
DATEDRAWN BY
9/21/11T. BOYD
DATEDESIGNED BY
UNLESS OTHERWISE SPECIFIED
INTERPRET DIMENSIONS AND TOLERANCES
IN ACCORDANCE WITH ASME Y14.5M-1994
DIMENSIONS ARE IN MM
TOLERANCES:
.X
0.5 Angles 0.5
.XX 0.25
.XXX
0.125
THIRD ANGLE PROJECTION
REVISION HISTORY
ZONE REV DESCRIPTION DATE APPR
- A PRELIMINARY DRAFT FOR REVIEW 9/21/11 TAB
B UPDATE NOTE 3A TO SPECIFY 1/2 HARD STAINLESS STEEL MATERIAL 10/19/11 TAB
C DECREASE MATERIAL THICKNESS FROM 1.5 TO 1.2MM 3/14/12 TAB
THIS DRAWING CONTAINS INTEL CORPORATION CONFIDENTIAL INFORMATION. IT IS DISCLOSED IN CONFIDENCE AND ITS CONTENTS
MAY NOT BE DISCLOSED, REPRODUCED, DISPLAYED OR MODIFIED, WITHOUT THE PRIOR WRITTEN CONSENT OF INTEL CORPORATION.
NOTES: UNLESS OTHERWISE SPECIFIED:
1. REFERENCE DOCUMENTS
ASME Y14.5M-1994 - STANDARD DIMENSION AND TOLERANCES
UL 94 - UL FLAMABILITY TESTING
99-0007-001 - INTEL WORKMANSHIP STANDARD - SYSTEMS MANUFACTURING
18-1201 - INTEL ENVIRONMENTAL PRODUCT CONTENT SPECIFICATION FOR
SUPPLIERS & OUTSOURCED MANUFACTURERS (FOUND ON
EHS WEBSITE - https://supplier.intel.com/static/EHS/)
2. 3D PART MODEL IS PER ENGINEERING BILL OF MATERIAL. DIMENSIONS CALLED OUT ON THE
DRAWING SHALL CONFORM TO THE DEFAULT TOLERANCE BLOCK UNLESS OTHERISE
SPECIFIED. THE 3D MODEL SHALL CONTROL ALL FEATURES OF THIS PART NOT DEFINED
ON THE DRAWING. MODEL TO BE INTERPRETED USING DATUM A (PRIMARY), DATUM B
(SECONDARY), AND DATUM C (TERTIARY) PER THE DRAWING CALLOUT.
3. MATERIAL: MAY USE INTEL ENGINEERING APPROVED EQUIVALENT
A) TYPE: SUS 304 1/2 HARD STAINLESS STEEL (REPORT ALLOY IN FAI STUDY)
B) THICKNESS: 1.2MM (.059") THICK
4. BURR HEIGHTS SHALL NOT EXCEED 10% OF MATERIAL THICKNESS.
5. THIS DRAWING TO BE USED IN CORRELATION WITH SUPPLIED 3D DATABASE FILE.
ALL DIMENSIONS AND TOLERANCES ON THIS DRAWING TAKE PRECEDENCE OVER
SUPPLIED FILE.
6. PART TO BE FLAT WITHIN 0.15mm.
7. BEND RADII 0.125mm (.005") MINIMUM.
8. CRITICAL TO FUNCTION DIMENSION (CTF)
MEASURED
9. BREAK ALL SHARP EDGES
10. ALL SUBSTANCES IN THIS PART MUST CONFORM TO INTEL ENVIRONMENTAL PRODUCT
SPECIFICATION BS-MTN-0001.
SCALE 2:1
X
Intel® Xeon® Processor E7 V2
Product Family-based Platform
HSINK STIFFENER