Intel® Desktop Board DQ57TM Product Guide Order Number: E78894-002
Revision History Revision -001 -002 Revision History First release of the Intel® Desktop Board DQ57TM Product Guide Second release of the Intel® Desktop Board DQ57TM Product Guide Date January 2010 March 2010 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules.
Preface This Product Guide gives information about board layout, component installation, BIOS update, and regulatory requirements for Intel® Desktop Board DQ57TM. Intended Audience The Product Guide is intended for technically qualified personnel. It is not intended for general audiences. Use Only for Intended Applications All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.
Intel Desktop Board DQ57TM Product Guide Terminology The table below gives descriptions of some common terms used in the product guide.
Contents 1 Desktop Board Features Supported Operating Systems..............................................................................11 Desktop Board Components.................................................................................12 Processor..........................................................................................................14 Intel® Q57 Express Chipset .................................................................................15 Main Memory......................
Intel Desktop Board DQ57TM Product Guide Installing and Removing a Processor .....................................................................37 Installing a Processor ..................................................................................37 Installing a Processor Fan Heat Sink ..............................................................42 Connecting the Processor Fan Heat Sink Cable................................................42 Removing the Processor ..................................
Contents B Regulatory Compliance Safety Standards ...............................................................................................75 Place Battery Marking .................................................................................75 European Union Declaration of Conformity Statement..............................................76 Product Ecology Statements ................................................................................77 Recycling Considerations .......................
Intel Desktop Board DQ57TM Product Guide Tables 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. viii Feature Summary.......................................................................................... 9 Intel Desktop Board DQ57TM Components .......................................................13 LAN Status LEDs States .................................................................................
1 Desktop Board Features This chapter briefly describes the features of Intel® Desktop Board DQ57TM. Table 1 summarizes the major features of the Desktop Board. Table 1. Feature Summary Form Factor Processor Support MicroATX (243.84 millimeters [9.60 inches] x 243.84 millimeters [9.
Intel Desktop Board DQ57TM Product Guide Table 1. Feature Summary (continued) Peripheral Interfaces • Fourteen USB 2.0 ports: ― Six ports are implemented with back panel connectors ― Eight ports are implemented with four dual-port internal headers • Five onboard Serial ATA (SATA) 3.
Desktop Board Features Supported Operating Systems The Desktop Board supports the following operating systems: • • • • • • • • • • • • • • • • • • • • Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Microsoft Windows* 7 Ultimate 64-bit edition Windows 7 Ultimate 32-bit edition Windows 7 Professional 64-bit edition Windows 7 Professional 32-bit edition Windows 7 Hom
Intel Desktop Board DQ57TM Product Guide Desktop Board Components Figure 1 shows the approximate location of the major components on Intel Desktop Board DQ57TM. Figure 1.
Desktop Board Features Table 2. Intel Desktop Board DQ57TM Components Label Description A PCI bus add-in card connector B PCI Express 2.0 x1 add-in card connector C Battery D Speaker E PCI Express 2.0 x1 add-in card connector F PCI Express 2.
Intel Desktop Board DQ57TM Product Guide Online Support For more information on Intel Desktop Board DQ57TM consult the following online resources: • Intel Desktop Board DQ57TM http://www.intel.com/products/motherboard/DQ57TM /index.htm • Desktop Board Support http://www.intel.com/support/motherboards/desktop/ DQ57TM • Available configurations for Intel Desktop Board DQ57TM http://www.intel.com/products/motherboard/DQ57TM /index.htm • Supported processors http://processormatch.intel.
Desktop Board Features Intel® Q57 Express Chipset The Intel Q57 Express Chipset, consisting of the Intel Q57 Platform Controller Hub (PCH), provides interfaces to the processor and the USB, SATA, LPC, audio, network, display, PCI, and PCI Express x1 interfaces. The PCH is a centralized controller for the board’s I/O paths.
Intel Desktop Board DQ57TM Product Guide Graphics Subsystem The board supports either integrated graphics (Intel Graphics Technology) or PCI Express 2.0 x16 graphics. Integrated Graphics The board supports integrated graphics through the Intel® Flexible Display Interface (Intel® FDI) for processors with Intel Graphics Technology. NOTE If using a processor with integrated graphics, the board will support only two of the three integrated graphics interfaces simultaneously: DisplayPort, DVI-I, DVI-D.
Desktop Board Features PCI Express* x16 Graphics The Intel Core i7, Intel Core i5, Intel Core i3, and Intel Pentium processors in an LGA1156 socket support discrete add-in graphics cards via the PCI Express 2.0 x16 add-in card connector. The board supports the following PCI Express speeds: • • PCI Express 2 frequency of 2.5 GHz which results in 5.0 Gb/s in each direction (500 MB/s) per lane.
Intel Desktop Board DQ57TM Product Guide LAN Subsystem The LAN subsystem includes: • Intel 82578DM Gigabit (10/100/1000 Mb/s) Ethernet LAN controller with support for: ⎯ Intel AMT 6.0 • ⎯ ASF 2.0 RJ-45 LAN connector with integrated status LEDs LAN software and drivers are available at http://downloadcenter.intel.com/. Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 2). These LEDs indicate the status of the LAN as shown in Table 3. Figure 2.
Desktop Board Features USB 2.0 Support The board supports up to 14 USB 2.0 ports provided by two EHCI host controllers in the PCH that allow the use of EHCI-compatible drivers. The port arrangement is as follows: • • Six back panel connectors Eight front panel ports (four dual-port internal headers) USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates.
Intel Desktop Board DQ57TM Product Guide Expandability Intel Desktop Board DQ57TM provides the following expansion capability: • • • One PCI Express 2.0 x16 interface Two PCI Express 2.
Desktop Board Features BIOS Security Passwords The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup and for booting the computer, with the following restrictions: • • • The supervisor password gives unrestricted access to view and change all Setup options.
Intel Desktop Board DQ57TM Product Guide During every POST, if a User hard disk drive password is set, POST execution will pause with the following prompt to force the user to enter the Master Key or User hard disk drive password: Enter Hard Disk Drive Password: Upon successful entry of the Master Key or User hard disk drive password, the system will continue with the normal POST. If the hard disk drive password is not correctly entered, the system will go back to the above prompt.
Desktop Board Features Platform Management and Protection Intel Desktop Board DQ57TM integrates several functions designed to manage the system and lower the total cost of ownership (TCO) of the system. These system management functions are designed to report errors, diagnose the system, and recover from system lockups without the aid of an external microcontroller. The board also includes several fan speed control and power management features.
Intel Desktop Board DQ57TM Product Guide The key features of Intel AMT include: • • • • • • • • • Secure Out of Band (OOB) system management that allows remote management of PCs regardless of system power or operating system state. Remote troubleshooting and recovery that can significantly reduce desk-side visits and potentially increasing efficiency of IT technical staff. Proactive alerting that decreases downtime and minimizes time to repair.
Desktop Board Features Intel ME “M” State LED The board has a red-colored Intel ME “M” state LED (see Figure 3). The “M” state is based on Intel ME status, as follows: • • • M0 = Intel ME is in full control in S0 M3 = Intel ME is in full control in S3-S5 for “out of bound” Intel manageability Moff = Intel ME is in sleep state after Intel ME timeout has occurred Figure 3. Location of the Intel ME “M” State LED Table 5 shows the expected behavior of the Intel ME “M” state LED. Table 5.
Intel Desktop Board DQ57TM Product Guide Intel® Virtualization Technology (Intel® VT) Intel VT is a processor technology that enables a platform to run multiple operating systems and applications as independent machines, allowing one computer system to function as multiple "virtual" systems. It also provides the “assisted hardware virtualization” required by some operating systems for backward compatibility, such as Windows XP Mode for Microsoft Windows 7.
Desktop Board Features NOTE Intel RPAT requires an Intel vPro technology-enabled computer that has an Intel RPAT-enabled BIOS, a connection with a power source, and the Internet. This service operates via a wired LAN connection only and requires a direct Internet connection (no proxy server) with the ability to connect to external Internet locations (locations outside the local network). A remote service provider supporting Intel RPAT must be used to perform remote management.
Intel Desktop Board DQ57TM Product Guide Power Management Power management is implemented at several levels, including software support through the Advanced Configuration and Power Interface (ACPI) and the following hardware support: • • • • • • • • • • Power connectors Fan headers LAN wake capabilities Instantly Available PC technology (Suspend to RAM) +5 V standby power indicator LED Wake from USB PCI Power Management Event signal (PME#) wakeup support PCI Express WAKE# signal support Wake from PS/2 dev
Desktop Board Features The Desktop Board has a 4-pin processor fan header and two 4-pin chassis fan headers that are compatible with 4-wire and 3-wire chassis fans. LAN Wake Capabilities CAUTION For LAN wake capabilities, the 5 V standby line for the power supply must be capable of delivering adequate +5 V standby current. Failure to provide adequate standby current when using this feature can damage the power supply. LAN wakeup capabilities enable remote wake-up of the computer through a network.
Intel Desktop Board DQ57TM Product Guide +5 V Standby Power Indicator LED CAUTION If the AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices. The Desktop Board’s standby power indicator LED, shown in Figure 4, is lit when there is standby power still present on the board even when the computer appears to be off.
Desktop Board Features Wake from USB NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB and an operating system that supports Wake from USB. USB bus activity wakes the computer from an ACPI S1 or S3 state. PCI PME# Signal Wake-up Support When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3, S4, or S5 state.
Intel Desktop Board DQ57TM Product Guide Onboard Speaker A speaker is mounted on the Desktop Board. The speaker provides audible error code (beep code) information during the Power-On Self-Test (POST). Refer to Appendix A for a description of the beep codes that may be generated during the POST. Real-Time Clock Subsystem A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years.
2 Installing and Replacing Desktop Board Components This chapter tells you how to: • • • • • • • • • • • • • Install the I/O shield Install and remove the Desktop Board Install and remove a processor Install and remove memory Install and remove a PCI Express x16 card Connect Serial ATA cables Connect to the internal headers Connect to the audio system Connect chassis fan and power supply cables Set the BIOS configuration jumper Clear passwords Clear CMOS Memory Replace the battery Before You Begin CAUTION
Intel Desktop Board DQ57TM Product Guide Installation Precautions When you install and test the Intel Desktop Board, observe all warnings and cautions in the installation instructions.
Installing and Replacing Desktop Board Components Installing the I/O Shield The Desktop Board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the Desktop Board in the chassis. Place the shield inside the chassis as shown in Figure 5. Press the shield into place so that it fits tightly and securely.
Intel Desktop Board DQ57TM Product Guide Installing and Removing the Desktop Board CAUTION Only qualified technical personnel should perform this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage. Refer to your chassis manual for instructions on installing and removing the Desktop Board.
Installing and Replacing Desktop Board Components Installing and Removing a Processor Instructions on how to install the processor on the Desktop Board are given below. Installing a Processor CAUTION Before installing or removing a processor, make sure the AC power has been removed by unplugging the power cord from the computer; the standby power LED should not be lit (see Figure 4 on page 30). Failure to do so could damage the processor and the board. To install a processor, follow these instructions: 1.
Intel Desktop Board DQ57TM Product Guide 3. Rotate the socket lever to lift the load plate away from the socket (Figure 8, A). Make sure that the load plate is in the fully open position (Figure 8, B) while being careful not to damage adjacent components. Figure 8.
Installing and Replacing Desktop Board Components 4. Remove the protective socket cover from the socket by placing your thumb against the front edge of the cover and resting your index finger on the rear grip (Figure 9, A). Lift the front edge of the socket to disengage the cover from the socket and lift the cover up and away from the socket (Figure 9, B). Do not touch the socket contacts. NOTE Do not discard the socket cover; save it for possible future use.
Intel Desktop Board DQ57TM Product Guide 5. Remove the processor from its protective cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor (see Figure 10). NOTE Do not discard the processor cover. Always replace the processor cover if you remove the processor from the socket. Figure 10. Remove the Processor from the Protective Cover 6.
Installing and Replacing Desktop Board Components 7. Lower the load plate over the processor while leaving the socket lever in the open position (Figure 12). Figure 12. Lower the Load Plate 8. Lower the socket lever (Figure 13, B) while making sure that the front edge of the load plate slides under the shoulder screw cap as the lever is lowered (Figure 13, A). Latch the socket lever under the load plate tab (Figure 13, C, D). Figure 13.
Intel Desktop Board DQ57TM Product Guide Installing a Processor Fan Heat Sink Intel Desktop Board DQ57TM has mounting holes for a processor fan heat sink. For instructions on how to attach the processor fan heat sink to the Desktop Board, refer to the boxed processor manual or boxed thermal solution manual. Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink power cable to the 4-pin processor fan header (see Figure 13).
Installing and Replacing Desktop Board Components Installing and Removing System Memory Desktop board DQ57TM has four 240-pin DDR3 DIMM sockets arranged as DIMM 0 and DIMM 1 in both Channel A and Channel B. NOTE A DIMM must be present in at least one of the DIMM 0 sockets when you are using only one or two DIMMs with a processor that does not support Intel Graphics Technology.
Intel Desktop Board DQ57TM Product Guide If additional memory is to be used, install another matched pair of DIMMs in the DIMM 1 (black) sockets of channels A and B (see Figure 16). Figure 16. Example Dual Channel Memory Configuration with Four DIMMs Three DIMMs If you want to use three DIMMs in a dual-channel configuration, install a matched pair of DIMMs equal in speed and size in the DIMM 0 (blue) socket of channel A and the DIMM 0 (blue) socket of channel B.
Installing and Replacing Desktop Board Components Installing DIMMs To make sure you have the correct DIMM, place it on the illustration of the DDR3 DIMM in Figure 18. All the notches should match with the DDR3 DIMM. Figure 18.
Intel Desktop Board DQ57TM Product Guide To install a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 33. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Remove the computer’s cover and locate the DIMM sockets (see Figure 19). 4. If a full length PCI Express graphics card is installed in the PCI Express x16 connector, remove the card to gain full access to the DIMM sockets. Figure 19.
Installing and Replacing Desktop Board Components Removing DIMMs To remove a DIMM, follow these steps: 1. 2. 3. 4. 5. 6. 7. 8. 9. Observe the precautions in "Before You Begin" on page 33. Turn off all peripheral devices connected to the computer. Turn off the computer. Remove the AC power cord from the computer. Remove the computer’s cover. If a full length PCI Express graphics card is installed in the PCI Express x16 connector, remove the card to gain access to the DIMMs.
Intel Desktop Board DQ57TM Product Guide Follow these instructions to install a PCI Express x16 graphics card: 1. Observe the precautions in "Before You Begin" on page 33. 2. Place the card in the PCI Express x16 connector (Figure 20, A) and press down on the card until it is completely seated in the connector and the card retention notch on the card snaps into place around the retention mechanism pin on the connector. 3.
Installing and Replacing Desktop Board Components Removing a PCI Express x16 Graphics Card Follow these instructions to remove a PCI Express x16 graphics card from a connector: 1. Observe the precautions in "Before You Begin" on page 33. 2. Disconnect the monitor cable from the graphics card back panel connector. 3. Remove the screw (Figure 21, A) that secures the card’s metal bracket to the chassis back panel. 4.
Intel Desktop Board DQ57TM Product Guide Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA protocol. Each cable can be used to connect one internal SATA drive to the Desktop Board. For correct cable function: 1. Observe the precautions in “Before You Begin” on page 33. 2. Attach one end of the SATA cable to one of the SATA connectors on the board (Figure 22, A) and attach the other end of the cable to the SATA drive (Figure 22, B). Figure 22.
Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to any of the internal headers, observe the precautions in “Before You Begin” on page 33. Figure 23 shows the location of the internal headers and connectors on Intel Desktop Board DQ57TM. Figure 23.
Intel Desktop Board DQ57TM Product Guide Front Panel Audio Header The front panel audio header shown in Figure 23, A supports both Intel High Definition Audio and AC ’97 Audio. Table 6 shows the pin assignments and signal names for HD Audio and Table 7 shows the pin assignments and signal names for AC ’97 Audio. Table 6.
Installing and Replacing Desktop Board Components S/PDIF Header Figure 23, C shows the location of the S/PDIF output header. Table 9 shows the pin assignments and signal names for the S/PDIF output header. Table 9. S/PDIF Header Signal Names Pin Description 1 Ground 2 S/PDIF Out 3 Key (no pin) 4 +5 VDC Chassis Intrusion Header Figure 23, D shows the location of the chassis intrusion header.
Intel Desktop Board DQ57TM Product Guide Front Panel Header Figure 23, F shows the location of the front panel header. Table 12 shows the pin assignments and signal names for the front panel header. Table 12.
Installing and Replacing Desktop Board Components Intel RPAT Header Figure 23, H shows the location of the Intel RPAT header. Table 14 shows the pin assignments and signal names for the Intel RPAT header. Table 14. Intel RPAT Header Signal Names Pin Description 1 RPAT# 2 Ground Serial Header Figure 23, I shows the location of the serial header. Table 15 shows the pin assignments and signal names for the serial header. Table 15.
Intel Desktop Board DQ57TM Product Guide Connecting to the Audio System After installing the Realtek audio driver from the Intel® Express Installer DVD-ROM, the multi-channel audio feature can be enabled. Figure 24 shows the back panel audio connectors. The default connector assignments are shown in the table. Item Description A Line in B Line out (front speaker/headphones) C Mic in Figure 24.
Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Supply Cables Connecting Chassis Fan Cables Connect chassis fan cables to the chassis fan headers on the Desktop Board. Figure 25 shows the location of the chassis fan headers. Figure 25.
Intel Desktop Board DQ57TM Product Guide Connecting Power Supply Cables CAUTION Failure to use an appropriate power supply and/or not connecting the 12 V power connector (Figure 26, A) to the Desktop Board may result in damage to the board or the system may not function properly. Figure 26 shows the location of the power connectors. The 2 x 12 pin main power connector (Figure 26, B) is backwards compatible with ATX12V power supplies with 2 x 10 connectors.
Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before moving the jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 27 shows the location of the Desktop Board’s BIOS configuration jumper block. Figure 27.
Intel Desktop Board DQ57TM Product Guide The three-pin BIOS jumper block enables board configuration to be done in the BIOS Setup program. Table 16 shows the jumper settings for the BIOS Setup program modes. Table 16. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Description Normal (default) (1-2) The BIOS uses the current configuration and passwords for booting. Configure (2-3) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu.
Installing and Replacing Desktop Board Components 10. Turn off the computer. Disconnect the computer’s power cord from the AC power source. 11. Remove the computer cover. 12. To restore normal operation, place the jumper on pins 1-2 as shown below. 13. Replace the cover, plug in the computer, and turn on the computer. Clearing CMOS Memory CAUTION Initiating a CMOS clear while the board is powered on or in standby mode may damage the board.
Intel Desktop Board DQ57TM Product Guide Figure 28. Location of the Clear CMOS Memory Jumper Block Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied.
Installing and Replacing Desktop Board Components PRÉCAUTION Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les réglementations locales en vigueur en matière de protection de l'environnement. FORHOLDSREGEL Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges.
Intel Desktop Board DQ57TM Product Guide ATENÇÃO Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as regulamentações ambientais da região. AŚCIAROŽZNAŚĆ Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па магчымасці, перепрацоўвацца.
Installing and Replacing Desktop Board Components PRECAUŢIE Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia mediului. ВНИМАНИЕ При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи должны быть утилизированы по возможности.
Intel Desktop Board DQ57TM Product Guide 66
Installing and Replacing Desktop Board Components To replace the battery, follow these steps: 1. Observe the precautions in "Before You Begin" (see page 33). 2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Locate the battery on the board (see Figure 29). 5. With a medium flat-bladed screwdriver, gently pry the battery free from its connector.
Intel Desktop Board DQ57TM Product Guide 68
3 Updating the BIOS The BIOS Setup program can be used to view and change the BIOS settings for the computer. You can access the BIOS Setup program by pressing the key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. This chapter tells you how to update the BIOS by either using the Intel® Express BIOS Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails.
Intel Desktop Board DQ57TM Product Guide Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update Utility You can use the information in this section to update the BIOS using either the Iflash Memory Update Utility or the ISO Image BIOS update file. Obtaining the BIOS Update File You can update to a new version of the BIOS by using the ISO Image BIOS update file (recommended), or Iflash BIOS update file.
Updating the BIOS Updating the BIOS with the ISO Image BIOS Update File The ISO Image BIOS update allows for the update of an Intel® Desktop Board BIOS to the latest production release regardless of the operating system installed on the computer's hard disk drive and without the need to remove the BIOS configuration jumper. It requires a blank CD-R, a read/writeable CD drive, and software capable of uncompressing and writing the ISO image file to CD.
Intel Desktop Board DQ57TM Product Guide Updating the BIOS with the Iflash Memory Update Utility With the Iflash Memory update utility you can update the system BIOS from a bootable CD-ROM, bootable USB flash drive, or other bootable USB media. The utility available on the Intel World Wide Web site provides a simple method for creating a bootable CD-ROM that will automatically update your BIOS.
A Error Messages and Indicators Intel Desktop Board DQ57TM reports POST errors in two ways: • • By sounding a beep code and blinking the front panel power LED By displaying an error message on the monitor BIOS Error Codes Whenever a recoverable error occurs during POST, the BIOS causes the board’s speaker to beep and the front panel power LED to blink an error message indicating the problem (see Table 18). Table 18. BIOS Beep Codes Type Pattern Frequency/Comments F2 Setup/F10 Boot Menu Prompt One 0.
Intel Desktop Board DQ57TM Product Guide Table 19. Front-panel Power LED Blink Codes Type Pattern F2 Setup/F10 Boot Menu Prompt None Note BIOS update in progress Off when the update begins, then on for 0.5 seconds, then off for 0.5 seconds. The pattern repeats until the BIOS update is complete. Video error (no addin graphics card installed) On-off (1.0 second each) two times, then a 2.5-second pause (off), the entire pattern repeats (blink and pause) until the system is powered off.
B Regulatory Compliance This appendix contains the following regulatory compliance information for Intel Desktop Board DQ57TM: • • • • • Safety standards European Union Declaration of Conformity statement Product Ecology statements Electromagnetic Compatibility (EMC) regulations Product certifications Safety Standards Intel Desktop Board DQ57TM complies with the safety standards stated in Table 21 when correctly installed in a compatible host system. Table 21.
Intel Desktop Board DQ57TM Product Guide European Union Declaration of Conformity Statement We, Intel Corporation, declare under our sole responsibility that the product Intel® Desktop Board DQ57TM is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directives 2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).
Regulatory Compliance Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC nuostatas. Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/EC u 2006/95/EC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/EC & 2006/95/EC. Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004/108/EC i 2006/95/EC.
Intel Desktop Board DQ57TM Product Guide Deutsch Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für ordnungsgemäßes Recycling zurückzugeben. Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte, verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der http://www.intel.
Regulatory Compliance Portuguese Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos são reciclados de maneira adequada. Consulte o site http://www.intel.
Intel Desktop Board DQ57TM Product Guide Lead-free 2LI/Pb-free 2LI Board The electronics industry is transitioning to European Union (EU) Restriction of Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the use of six materials. One of these restricted materials is lead. Lead is the most common and problematic of the RoHS restricted materials. There are exemptions in RoHS that allow the use of lead in some very limited locations in electronic products.
Regulatory Compliance Table 22. Lead-Free Second Level Interconnect Marks Description Mark This symbol is used to identify electrical and electronic assemblies and components in which the Pb concentration level in the Desktop Board substrate and the solder connections from the board to the components (second-level interconnect) is not greater than 0.1% by weight (1000 ppm).
Intel Desktop Board DQ57TM Product Guide China RoHS “China RoHS” is the term used by industry generally to describe legislation implemented by the Ministry of Information Industry (MII) in the People's Republic of China for the control of pollution by electronic information products (EIP). The official title of the China RoHS regulation is “Management Methods for Controlling Pollution by Electronic Information Products.” China RoHS bans the same substances and has the same limits as EU RoHS.
Regulatory Compliance The China MII stipulates that a material Self Declaration Table (SDT) must be included in a product’s user documentation. The SDT for Intel Desktop Board DQ57TM is shown in Figure 30. Figure 30.
Intel Desktop Board DQ57TM Product Guide EMC Regulations Intel Desktop Board DQ57TM complies with the EMC regulations stated in Table 24 when correctly installed in a compatible host system. Table 24. EMC Regulations Regulation (Class B) Title FCC 47 CFR Part 15, Subpart B Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (USA) ICES-003 Issue 4 Interference-Causing Equipment Standard, Digital Apparatus.
Regulatory Compliance Korean Class B statement translation: This is household equipment that is certified to comply with EMC requirements. You may use this equipment in residential environments and other non-residential environments. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly.
Intel Desktop Board DQ57TM Product Guide Product Certifications Board-Level Certification Markings Intel Desktop Board DQ57TM has the product certification markings shown in Table 25. Table 25. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel Desktop Boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Includes Intel name and DQ57TM model designation. CE mark.
Regulatory Compliance Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used. Agency certification marks on the product are proof of certification. Typical product certifications include: In Europe The CE marking signifies compliance with all applicable European requirements.
Intel Desktop Board DQ57TM Product Guide 88
