Intel® Desktop Board DG45FC Product Guide Order Number: E30026-001
Revision History Revision -001 Revision History First release of the Intel® Desktop Board DG45FC Product Guide Date May 2008 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules.
Preface This Product Guide gives information about board layout, component installation, BIOS update, and regulatory requirements for Intel® Desktop Board DG45FC. Intended Audience The Product Guide is intended for technically qualified personnel. It is not intended for general audiences. Use Only for Intended Applications All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.
Intel Desktop Board DG45FC Product Guide NOTE Notes call attention to important information. Terminology The table below gives descriptions of some common terms used in the product guide.
Contents 1 Desktop Board Features Desktop Board Components.................................................................................11 Processor..........................................................................................................13 Main Memory.....................................................................................................13 Intel® G45 Express Chipset .................................................................................
Intel Desktop Board DG45FC Product Guide Installing the I/O Shield ......................................................................................29 Installing and Removing the Desktop Board ...........................................................30 Installing and Removing a Processor .....................................................................31 Installing a Processor ..................................................................................
Contents A Error Messages and Indicators BIOS Beep Codes ...............................................................................................65 BIOS Error Messages ..........................................................................................65 B Regulatory Compliance Safety Standards ...............................................................................................67 Place Battery Marking .................................................................................
Intel Desktop Board DG45FC Product Guide 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. viii Front Panel Audio Header Signal Names for Intel High Definition Audio.................42 Chassis Intrusion Header ...............................................................................42 Front Panel CIR Receiver (Input) Header Signal Names ......................................43 Back Panel CIR Header Emitter (Output) Header Signal Names ...........................43 USB 2.
1 Desktop Board Features This chapter briefly describes the features of Intel® Desktop Board DG45FC. Table 1 summarizes the major features of the Desktop Board. Table 1. Feature Summary Form Factor Mini-ITX (171.45 millimeters [6.75 inches] x 171.45 millimeters [6.75 inches]) Processor Support for an Intel® processor in the LGA775 package Main Memory • Two 240-pin, DDR2 1.
Intel Desktop Board DG45FC Product Guide Table 1.
Desktop Board Features Desktop Board Components Figure 1 shows the approximate location of the major components on Desktop Board DG45FC. Figure 1.
Intel Desktop Board DG45FC Product Guide Table 2. Desktop Board DG45FC Components Label Description A Front panel audio header B Back panel connectors C Back panel CIR emitter (output) D 12 V processor core voltage connector (2 x 2 pin) E High-speed USB 2.
Desktop Board Features Processor CAUTION Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin) power connector to the Desktop Board may result in damage to the board, or the system may not function properly. Desktop Board DG45FC supports an Intel processor in the LGA775 package. Processors are not included with the Desktop Board and must be purchased separately. The processor connects to the Desktop Board through the LGA775 socket.
Intel Desktop Board DG45FC Product Guide NOTE System resources and hardware (such as PCI Express) require physical memory address locations that can reduce available addressable system memory. This could result in a reduction of as much as 1 GB or more of physical addressable memory being available to the operating system and applications, depending on the system configuration and operating system. Go to the following locations for more information about: • • • SDRAM specifications, http://intel.
Desktop Board Features Intel G45 Graphics Subsystem The Intel G45 Express Chipset provides DVI-I and HDMI support via the integrated Intel Graphics Media Accelerator X4500HD (GMA X4500HD) graphics controller. The Intel GMA X4500HD graphics controller has the following features: • • • Advanced graphics performance, including: ⎯ DirectX10* and OpenGL* 2.0 compliant ⎯ Shader Model 4.
Intel Desktop Board DG45FC Product Guide Audio Subsystem The onboard audio subsystem consists of the following: • • • • Intel ICH10R I/O controller hub IDT 92HD73E audio codec Intel High Definition Audio front panel audio header Back panel audio connectors including an optical S/PDIF output connector The audio subsystem supports the following features: • • • • A signal-to-noise (S/N) ratio of 95 dB Independent multi-streaming 7.
Desktop Board Features Legacy Input/Output (I/O) Controller The I/O controller features the following: • • • • • • Low pin count (LPC) interface One serial port interface via an onboard header Consumer Infrared (CIR) support Serial IRQ interface compatible with serialized IRQ support for PCI Express systems Intelligent power management, including a programmable wake up event interface PCI Express power management support LAN Subsystem The LAN subsystem includes: • • • Intel® ICH10R Intel 82567LF Gigabit
Intel Desktop Board DG45FC Product Guide Figure 2. LAN Status LEDs Table 4 describes the LED states when the board is powered up and the LAN subsystem is operating. Table 4. LAN Connector LEDs LED LED Color A (Link) Green B (Speed) N/A LED State Indicates Off LAN link is not established On LAN link is established Blinking LAN activity is occurring Off 10 Mb/s data rate Green On 100 Mb/s data rate Yellow On 1000 Mb/s data rate Hi-Speed USB 2.
Desktop Board Features Serial ATA The Desktop Board supports five Serial ATA channels (3.0 Gb/s) via ICH10R, connecting one device per channel. One channel is configured as an eSATA channel.
Intel Desktop Board DG45FC Product Guide BIOS The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI Express and SATA auto-configuration utilities, and the video BIOS. The BIOS is stored in the Serial Peripheral Interface (SPI) Flash device. The BIOS can be updated by following the instructions on page 55 in Chapter 3.
Desktop Board Features Hardware Management Features The hardware management features of Desktop Board DG45FC enable the board to be compatible with the Wired for Management (WfM) specification.
Intel Desktop Board DG45FC Product Guide Power Management Features Power management is implemented at several levels, including: • • • Software support through the Advanced Configuration and Power Interface (ACPI) Hardware support: ⎯ Power connectors ⎯ Fan headers ⎯ LAN wake capabilities ⎯ Instantly Available PC technology (Suspend to RAM) ⎯ +5 V standby power indicator LED ⎯ Wake from USB ⎯ WAKE# signal wake-up support ⎯ Wake from Consumer IR ENERGY STAR qualified ACPI ACPI gives the operating system d
Desktop Board Features Fan Headers The function/operation of the fans is as follows: • • • • The fans are on when the computer is in the ACPI S0 state. The fans are off when the computer is in the ACPI S3, S4, or S5 state. All fan headers support closed-loop fan control that can adjust the fan speed based on thermal conditions. All fan headers have a +12 V DC connection. The Desktop Board has a 4-pin processor fan header and a 3-pin chassis fan header.
Intel Desktop Board DG45FC Product Guide +5 V Standby Power Indicator CAUTION If the AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices. The Desktop Board’s standby power indicator, shown in Figure 3, is lit when there is standby power still present on the board even when the computer appears to be off.
Desktop Board Features WAKE# Signal Wake-up Support When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from an ACPI S1, S3, S4, or S5 state. Wake from CIR Consumer IR device activity wakes the computer from an ACPI S1 or S3 state. ENERGY STAR* Qualified In 2007, the US Department of Energy and the US Environmental Protection Agency revised the ENERGY STAR requirements. Intel worked directly with these two governmental agencies to define the new requirements.
Intel Desktop Board DG45FC Product Guide 26
2 Installing and Replacing Desktop Board Components This chapter tells you how to: • • • • • • • • • • • Install the I/O shield Install and remove the Desktop Board Install and remove a processor Install and remove memory Connect the Serial ATA cables Connect to the internal headers Connect to the onboard audio system Connect chassis fan and power supply cables Set the BIOS configuration jumper Clear passwords Replace the battery Before You Begin CAUTIONS The procedures in this chapter assume familiarity
Intel Desktop Board DG45FC Product Guide Installation Precautions When you install and test the Intel Desktop Board, observe all warnings and cautions in the installation instructions.
Installing and Replacing Desktop Board Components Installing the I/O Shield The Desktop Board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the Desktop Board in the chassis. Place the shield inside the chassis as shown in Figure 4. Press the shield into place so that it fits tightly and securely.
Intel Desktop Board DG45FC Product Guide Installing and Removing the Desktop Board CAUTION Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage. Refer to your chassis manual for instructions on installing and removing the Desktop Board.
Installing and Replacing Desktop Board Components Installing and Removing a Processor This section contains information on how to install and remove a processor on the Desktop Board. Installing a Processor CAUTION Before installing or removing the processor, make sure the AC power has been removed by unplugging the power cord from the computer; the standby power LED should not be lit (see Figure 3 on page 24). Failure to do so could damage the processor and the board.
Intel Desktop Board DG45FC Product Guide 3. Lift the load plate (Figure 7, A). Do not touch the socket contacts (Figure 7, B). Figure 7. Lift the Load Plate 4. Remove the plastic protective socket cover from the load plate (Figure 8). Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket. Figure 8.
Installing and Replacing Desktop Board Components 5. Remove the processor from the protective processor cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor (see Figure 9). Do not discard the protective processor cover. Always replace the processor cover if the processor is removed from the socket. Figure 9. Remove the Processor from the Protective Processor Cover 6. Hold the processor with your thumb and index fingers oriented as shown in Figure 10.
Intel Desktop Board DG45FC Product Guide 7. Pressing down on the load plate (Figure 11, A), close and engage the socket lever (Figure 11, B). Figure 11. Close the Load Plate Installing a Processor Fan Heat Sink Desktop Board DG45FC has mounting holes for a processor fan heat sink. For instructions on how to attach the processor fan heat sink to the Desktop Board, refer to the boxed processor manual.
Installing and Replacing Desktop Board Components Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink cable to the 4-pin processor fan header (see Figure 12). A fan with a 4-pin connector as shown in Figure 12, A is recommended; however, a fan with a 3-pin connector (Figure 12, B) can be used. However, since a fan with a 3-pin connector cannot use the onboard fan control, the fan will always operate at full speed. Figure 12.
Intel Desktop Board DG45FC Product Guide Installing and Removing Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications, the board requires DIMMs that support the Serial Presence Detect (SPD) data structure. The desktop board has two 240-pin DDR2 DIMM sockets providing Channel A and Channel B. For dual-channel performance, install a matched pair of DIMMs equal in speed and size (see Figure 13). Figure 13.
Installing and Replacing Desktop Board Components Installing DIMMs To make sure you have the correct DIMM, place it on the illustration of the DDR2 DIMM in Figure 14. All the notches should match with the DDR2 DIMM. Figure 14.
Intel Desktop Board DG45FC Product Guide To install a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Remove the computer’s cover and locate the DIMM sockets (see Figure 15). Figure 15. Installing a DIMM 4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. 5.
Installing and Replacing Desktop Board Components 7. Insert the bottom edge of the DIMM into the socket. 8. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 9. Replace the computer’s cover and reconnect the AC power cord. Removing DIMMs To remove a DIMM, follow these steps: 1. 2. 3. 4. 5. Observe the precautions in "Before You Begin" on page 27. Turn off all peripheral devices connected to the computer.
Intel Desktop Board DG45FC Product Guide Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA protocol. Each cable can be used to connect a single SATA drive to the Desktop Board. For correct cable function: 1. Observe the precautions in "Before You Begin" on page 27. 2. Attach one end the SATA cable to one of the SATA connectors on the board (Figure 16, A). 3. Attach the other end of the SATA cable to the SATA drive (Figure 16, B). Figure 16.
Installing and Replacing Desktop Board Components Connecting to Internal Headers and Connectors Before connecting cables to the internal headers and connectors, observe the precautions in “Before You Begin” on page 27. Figure 17 shows the location of the internal headers and connectors. Item A B C D Description Audio Chassis intrusion Back panel CIR emitter USB 2.0 Item E F G H Description Serial Front panel CIR receiver Alternate front panel power LED Front panel Figure 17.
Intel Desktop Board DG45FC Product Guide Front Panel HD Audio Header Figure 17, A shows the location of the front panel audio header. Table 5 shows the pin assignments for the front panel audio header. Table 5.
Installing and Replacing Desktop Board Components NOTE The Consumer IR option must be enabled in the system BIOS before it can function. Press at boot to enter the system BIOS, and go to Advanced > Peripheral Configuration > Enhanced Consumer IR, and set this option to Enabled. Table 7 shows the pin assignments for the front panel CIR receiver (input) header and Table 8 shows the pin assignments for the back panel CIR emitter (output) header. Table 7.
Intel Desktop Board DG45FC Product Guide Serial Port Header See Figure 17, E for the location of the serial port header. Table 10 shows the pin assignments for the header. Table 10. Serial Port Header Signal Names Pin Signal Name Pin Signal Name 1 DCD 2 RXD# 3 TXD# 4 DTR 5 Ground 6 DSR 7 RTS 8 CTS 9 RI 10 No Connection Alternate Front Panel Power LED Header Figure 17, G shows the location of the alternate front panel power LED header.
Installing and Replacing Desktop Board Components Connecting to the Audio System After installing the IDT audio driver from the Intel Express Installer DVD-ROM, the multi-channel audio feature can be enabled. Figure 18 shows the back panel audio connectors. Item Description A Rear Surround Left/Right B Center Channel and LFE (Subwoofer) C Side Surround/Line In D Line Out E Mic In F S/PDIF Digital Audio Out (Optical) Figure 18.
Intel Desktop Board DG45FC Product Guide Connecting Chassis Fan and Power Supply Cables Chassis Fan Cables Connect chassis fan cables to the 3-pin chassis fan header on the Desktop Board. Figure 19 shows the location of the chassis fan headers. Figure 19.
Installing and Replacing Desktop Board Components Power Supply Cables CAUTION Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin) power connector to the Desktop Board may result in damage to the board or the system may not function properly. The 2 x 12 pin main power connector on the Desktop Board is backwards compatible with ATX12V power supplies with 2 x 10 connectors. Figure 20 shows the location of the Desktop Board power connectors. Figure 20.
Intel Desktop Board DG45FC Product Guide Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before moving the jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 21 shows the location of the Desktop Board’s BIOS configuration jumper block. Figure 21. Location of the BIOS Configuration Jumper Block The three-pin BIOS jumper block enables all board configurations to be done in the BIOS Setup program.
Installing and Replacing Desktop Board Components Table 13. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Description Normal (default) (1-2) The BIOS uses the current configuration and passwords for booting. Configure (2-3) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords. Recovery (None) The BIOS recovers data in the event of a failed BIOS update.
Intel Desktop Board DG45FC Product Guide 12. To restore normal operation, place the jumper on pins 1-2 as shown below. 13. Replace the cover, plug in the computer, and turn on the computer. Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery.
Installing and Replacing Desktop Board Components VARO Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti. VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.
Intel Desktop Board DG45FC Product Guide Προσοχή Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς κανονισμούς. VIGYÁZAT Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell hasznosítani.
Installing and Replacing Desktop Board Components POZOR Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo. Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi. . UYARI Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır. OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Intel Desktop Board DG45FC Product Guide To replace the battery, follow these steps: 1. Observe the precautions in "Before You Begin" (see page 27). 2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Locate the battery on the board (see Figure 22). 5. Push the battery retention clip aside and remove the battery from the connector as shown in Figure 22.
3 Updating the BIOS The BIOS Setup program can be used to view and change the BIOS settings for the computer. You can access the BIOS Setup program by pressing the key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails.
Intel Desktop Board DG45FC Product Guide Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update Utility You can use the information in this section to update the BIOS using either the Iflash Memory Update Utility or the ISO Image BIOS update file. Obtaining the BIOS Update File You can update to a new version of the BIOS by using the ISO Image BIOS update file (recommended), or Iflash BIOS update file.
Updating the BIOS CAUTION Do not interrupt the process or the system may not function properly. Follow these instructions to upgrade the BIOS using the ISO Image BIOS file: 1. Download the ISO Image BIOS file. 2. Using software capable of uncompressing and writing an ISO image file to CD, burn the data to a blank CD. NOTE Copying the ISO Image BIOS file to CD will not work. The completed CD should contain multiple files and a directory. 3.
Intel Desktop Board DG45FC Product Guide CAUTION Do not interrupt the process or the system may not function properly. 1. Uncompress the BIOS update file and copy the .BIO file, IFLASH.EXE, and .ITK file (optional) to a bootable USB flash drive or other bootable USB media. 2. Configure the BIOS or use the F10 option during POST to boot to the USB device. 3. Manually run the IFLASH.EXE file from the USB device and manually update the BIOS.
4 Configuring for RAID (Intel® Matrix Storage Technology (Intel® MST)) NOTE Intel Matrix Storage Technology requires a Microsoft Windows Vista or Microsoft Windows XP operating system and SATA hard drives. Configuring the BIOS for Intel Matrix Storage Technology 1. Assemble your system and attach one or more SATA hard drives to the SATA connectors. 2. Enter system BIOS Setup by pressing the key after the Power-On-Self-Test (POST) memory tests begin. 3.
Intel Desktop Board DG45FC Product Guide Loading the Intel Matrix Storage Technology RAID Drivers and Software 1. Begin Windows Setup by booting from the Windows installation CD. 2. If you will be using Microsoft Windows XP, press at the beginning of Windows Setup to install a third-party SCSI or RAID driver. When prompted, insert the diskette labeled Intel Matrix Storage Technology RAID Driver. Install the Intel® ICH10R SATA RAID Controller driver.
5 Configuring for Intel® Rapid Recover Technology Intel Rapid Recover technology utilizes RAID 1 (mirroring) functionality to copy data from a designated master drive to a designated recovery drive. The master and recovery drives must span 100 percent of the available hard drive space of an array, and only one recovery volume can be present on a system. You can select whether you want the master drive data to be copied to the recovery drive continuously or on request.
Intel Desktop Board DG45FC Product Guide Creating a Recovery Volume A recovery volume consists of two disks – a master disk and a recovery disk. A recovery volume can be created with either the RAID Option ROM (OROM) or the Intel® Matrix Storage Console application. Creating a Recovery Volume Using the RAID Option ROM To create a recovery volume using the RAID OROM, complete the following steps: 1. Enter the RAID OROM by pressing the and keys simultaneously when prompted during system POST. 2.
Configuring for Intel® Rapid Recover Technology 6. Select the Update policy – Continuous update or Update on request. 7. Select Finish to complete the creation of the recovery volume. The system will synchronize the master disk with the recovery disk once after the creation of the recovery volume. Disk Synchronization Mode There are two modes of updating or synchronizing the recovery disk with the master disk – either continuous update or manual update.
Intel Desktop Board DG45FC Product Guide To un-mount the recovery disk, complete the following steps: 1. In the Advanced mode, right-click on the recovery volume name. 2. Select Access Recovery Drive Files. 3. Select OK on the information dialog box. The recovery disk is now un-mounted and reappears in Intel Matrix Storage Console.
A Error Messages and Indicators Desktop Board DG45FC reports POST errors in two ways: • • By sounding a beep code By displaying an error message on the monitor BIOS Beep Codes The BIOS also issues a beep code (one long tone followed by two short tones) during POST if the video configuration fails (a faulty video card or no card installed) or if an external ROM module does not properly checksum to zero. Table 14 lists the BIOS codes. Table 14.
Intel Desktop Board DG45FC Product Guide 66
B Regulatory Compliance This appendix contains the following regulatory compliance information for Desktop Board DG45FC: • • • • • Safety standards European Union Declaration of Conformity statement Product Ecology statements Electromagnetic Compatibility (EMC) regulations Product certifications Safety Standards Desktop Board DG45FC complies with the safety standards stated in Table 16 when correctly installed in a compatible host system. Table 16.
Intel Desktop Board DG45FC Product Guide European Union Declaration of Conformity Statement We, Intel Corporation, declare under our sole responsibility that the product Intel® Desktop Board DG45FC is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directives 2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).
Regulatory Compliance Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/EC u 2006/95/EC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/EC & 2006/95/EC. Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004/108/EC i 2006/95/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC & 2006/95/EC.
Intel Desktop Board DG45FC Product Guide Deutsch Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für ordnungsgemäßes Recycling zurückzugeben. Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte, verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der http://intel.
Regulatory Compliance Portuguese Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos são reciclados de maneira adequada. Consulte o site http://intel.
Intel Desktop Board DG45FC Product Guide Lead-free 2LI/Pb-free 2LI Board The electronics industry is transitioning to European Union (EU) Restriction of Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the use of six materials. One of these restricted materials is lead. Lead is the most common and problematic of the RoHS restricted materials. There are exemptions in RoHS that allow the use of lead in some very limited locations in electronic products.
Regulatory Compliance Table 17. Lead-Free Second Level Interconnect Marks Description Mark This symbol is used to identify electrical and electronic assemblies and components in which the Pb concentration level in the Desktop Board substrate and the solder connections from the board to the components (second-level interconnect) is not greater than 0.1% by weight (1000 ppm).
Intel Desktop Board DG45FC Product Guide China RoHS “China RoHS” is the term used by industry generally to describe legislation implemented by the Ministry of Information Industry (MII) in the People's Republic of China for the control of pollution by electronic information products (EIP). The official title of the China RoHS regulation is “Management Methods for Controlling Pollution by Electronic Information Products.” China RoHS bans the same substances and has the same limits as EU RoHS.
Regulatory Compliance The China MII stipulates that a material Self Declaration Table (SDT) must be included in a product’s user documentation. The SDT for Desktop Board DG45FC is shown in Figure 23. Figure 23.
Intel Desktop Board DG45FC Product Guide EMC Regulations Desktop Board DG45FC complies with the EMC regulations stated in Table 19 when correctly installed in a compatible host system. Table 19. EMC Regulations Regulation (Class B) Title FCC 47 CFR Part 15, Subpart B Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (USA) ICES-003 Issue 4 Interference-Causing Equipment Standard, Digital Apparatus.
Regulatory Compliance Korean Class B statement translation: This is household equipment that is certified to comply with EMC requirements. You may use this equipment in residential environments and other non-residential environments. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly.
Intel Desktop Board DG45FC Product Guide Product Certifications Board-Level Certification Markings Desktop Board DG45FC has the product certification markings shown in Table 20. Table 20. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel Desktop Boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Includes Intel name and DG45FC model designation. CE mark.
Regulatory Compliance Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used. Agency certification marks on the product are proof of certification. Typical product certifications include: In Europe The CE marking signifies compliance with all applicable European requirements.
Intel Desktop Board DG45FC Product Guide 80
