G Intel® Desktop Board D955XCS Product Guide Order Number: C98669-002 H I J
Revision History Revision Revision History -001 First release of the Intel® Desktop Board D955XCS Product Guide -002 Second release of the Intel® Desktop Board D955XCS Product Guide Date May 2005 June 2005 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules.
Preface This Product Guide gives information about board layout, component installation, BIOS updates, and regulatory requirements for Intel® Desktop Board D955XCS. Intended Audience The Product Guide is intended only for technically qualified personnel. Intended Uses All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations.
Intel Desktop Board D955XCS Product Guide Terminology The table below gives descriptions to some common terms used in the product guide.
Contents 1 Desktop Board Features Supported Operating Systems .............................................................................................. 10 Desktop Board Components ................................................................................................. 11 Processor .............................................................................................................................. 13 Power Requirements for Intel® Pentium® Processor Extreme Edition .....................
Intel Desktop Board D955XCS Product Guide Installing and Removing the Desktop Board ......................................................................... 27 Installing and Removing a Processor.................................................................................... 28 Installing a Processor................................................................................................... 28 Installing the Processor Fan Heat Sink ...............................................................
Contents A Error Messages and Indicators BIOS Beep Codes................................................................................................................. 65 BIOS Error Messages ........................................................................................................... 65 B Regulatory Compliance Safety Regulations ................................................................................................................
Intel Desktop Board D955XCS Product Guide Tables 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. viii Feature Summary............................................................................................................. 9 Desktop Board D955XCS Components ......................................................................... 12 Power Supply Requirements ..........................................................................................
1 Desktop Board Features This chapter briefly describes the main features of Intel® Desktop Board D955XCS. Table 1 summarizes the major features of the desktop board. Table 1. Feature Summary Form Factor BTX (12.875” x 10.
Intel Desktop Board D955XCS Product Guide Table 1. Feature Summary (continued) Peripheral Interfaces • One front panel audio header (yellow) • Up to eight USB 2.0 ports ⎯ Four ports routed to the back panel ⎯ Four ports routed to two USB headers • Up to eight Serial ATA channels (one device per channel) — Four RAID capable Serial ATA (3.
Desktop Board Features Desktop Board Components Figure 1 shows the approximate location of the major components on Desktop Board D955XCS. IEEE 1394a Line In Optical Line Out (Toslink) Coaxial Line Out A C B D E F G Y X G R Intel 82801 (ICH7R) W Channel B DIMM 0 Channel B DIMM 1 H H R Intel 82955X (MCH) Channel A DIMM 1 Channel A DIMM 0 I I J K L J V U T S R Q O N M P OM17778 Figure 1.
Intel Desktop Board D955XCS Product Guide Table 2. Desktop Board D955XCS Components Label Description A Front panel audio header (yellow) B Serial ATA connectors (four, black, ICH7R) C USB 2.
Desktop Board Features Processor CAUTION Failure to use the appropriate power supply (below) and/or not connecting the 12 V (2x4) power connector to the desktop board may result in damage to the board or the system may not function properly. Table 3. Power Supply Requirements Platform Compatibility Guide Power Supply Requirements 05B 12V2 rating of 16 A continuous and 19 A peak current for 10mS 05A 12V2 rating of 13 A continuous and 16.5 A peak current for 10mS 04B or 04A ATX12V (version 2.
Intel Desktop Board D955XCS Product Guide Main Memory NOTE To be fully compliant with all applicable Intel® SDRAM memory specifications, the desktop board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your memory modules do not support SPD, you will see a notification to this effect on the screen at power up. The BIOS will attempt to configure the memory controller for normal operation.
Desktop Board Features Audio Subsystem The desktop board includes a flexible 8-channel audio subsystem based on the Intel High Definition Audio codec: The audio subsystem features: • Impedance sensing capability for jack re-tasking • S/N (signal-to-noise) ratio: > 90 dB • Power management support for ACPI 2.
Intel Desktop Board D955XCS Product Guide Input/Output (I/O) Controller The super I/O controller features the following: • One serial port • One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) support • Serial IRQ interface compatible with serialized IRQ support for PCI systems • PS/2-style mouse and keyboard interfaces • Interface for one 1.2 MB, 1.44 MB, or 2.
Desktop Board Features Table 4 describes the LED states when the board is powered up and the 10/100/1000 Gigabit Ethernet LAN subsystem is operating. Table 4. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs LED LED Color LED State Indicates Left Green Off LAN link is not established. On LAN link is established. Right Blinking LAN activity is occurring. N/A Off 10 Mb/s data rate is selected. Green On 100 Mb/s data rate is selected. Yellow On 1000 Mb/s data rate is selected.
Intel Desktop Board D955XCS Product Guide Expandability The desktop board supports the following: • One PCI Express x16 add-in card • One PCI Express x4 add-in card (routed to the physical x16 connector) • One PCI Express x1 add-in card • Four PCI bus add-in cards Related Links For information about installing the PCI Express x16 card, see page 37 in Chapter 2. BIOS The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI and IDE auto-configuration utilities, and the video BIOS.
Desktop Board Features Related Links: For instructions on resetting the password, see Clearing Passwords on page 52. Chassis Intrusion The desktop board supports a chassis security feature that detects if the chassis cover has been removed. The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the desktop board. See Figure 25 on page 46 for the location of the chassis intrusion header.
Intel Desktop Board D955XCS Product Guide Suspend to RAM (Instantly Available PC Technology) CAUTION For Instantly Available PC technology, the 5 V standby line for the power supply must be capable of delivering adequate +5 V standby current. Failure to provide adequate standby current when using this feature can damage the power supply and/or affect ACPI S3 sleep state functionality.
Desktop Board Features Resume on Ring The operation of Resume on Ring can be summarized as follows: • Resumes operation from either ACPI S1 or ACPI S3 state • Requires only one call to access the computer • Detects incoming call similarly for external and internal modems • Requires modem interrupt be unmasked for correct operation Wake from USB NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB. USB bus activity wakes the computer from an ACPI S1 or S3 state.
Intel Desktop Board D955XCS Product Guide 22
2 Installing and Replacing Desktop Board Components This chapter tells you how to: • Install the I/O shield • Install and remove the desktop board • Install and remove a processor and memory • Install and remove a PCI Express x16 add-in card • Connect the IDE and Serial ATA cables • Connect internal headers • Install the rear and front panel USB/IEEE 1394/audio solutions • Connect fan and power cables • Identify other connectors • Set the BIOS configuration jumper • Clear passwords • Identify back panel con
Intel Desktop Board D955XCS Product Guide Installation Precautions When you install and test the Intel desktop board, observe all warnings and cautions in the installation instructions.
Installing and Replacing Desktop Board Components Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used. Agency certification marks on the product are proof of certification. Typical product certifications include: In Europe The CE marking signifies compliance with all applicable European requirements.
Intel Desktop Board D955XCS Product Guide Installing the I/O Shield The desktop board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the desktop board in the chassis. Place the shield inside the chassis as shown in Figure 4. Press the shield into place so that it fits tightly and securely.
Installing and Replacing Desktop Board Components Installing and Removing the Desktop Board WARNING Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage. NOTE Refer to Appendix B for regulatory requirements.
Intel Desktop Board D955XCS Product Guide Installing and Removing a Processor Instructions on how to install the processor to the desktop board are given below. Installing a Processor CAUTION Before installing or removing the processor, make sure that AC power has been removed by unplugging the power cord from the computer; the standby power LED should not be lit (see Figure 3 on page 20). Failure to do so could damage the processor and the board. To install a processor, follow these instructions: 1.
Installing and Replacing Desktop Board Components 4. Remove the protective socket cover from the load plate. Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket (see Figure 8, E). E OM17228 Figure 8. Remove the Protective Socket Cover 5. Remove the processor from the protective processor cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor (see Figure 9).
Intel Desktop Board D955XCS Product Guide 6. Hold the processor with your thumb and index fingers oriented as shown in Figure 10. Make sure fingers align to the socket cutouts (see Figure 10, F). Align notches (see Figure 10, G) with the socket see (Figure 10, H). Lower the processor straight down without tilting or sliding the processor in the socket. G G H F H F OM17214 Figure 10. Install the Processor 7.
Installing and Replacing Desktop Board Components Installing the Processor Fan Heat Sink Desktop Board D955XCS has an integrated processor fan heat sink retention mechanism (RM). For instructions on how to attach the processor fan heat sink to the integrated processor fan heat sink RM, refer to the boxed processor manual or the Intel World Wide Web site at: http://support.intel.com/support/processors/pentium4/intnotes478.
Intel Desktop Board D955XCS Product Guide Installing and Removing Memory CAUTION To be fully compliant with all applicable Intel SDRAM memory specifications, the board requires DIMMs that support the Serial Presence Detect (SPD) data structure. You can access the PC Serial Presence Detect Specification at: http://www.intel.com/technology/memory/ddr/specs/dda18c32_64_128x72ag_a.
Installing and Replacing Desktop Board Components Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A. Install a DIMM equal in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B (see Figure 15). Channel A 256 MB, 533 MHz DIMM 0 256 MB, 533 MHz DIMM 1 Channel B 512 MB, 533 MHz DIMM 0 DIMM 1 Figure 15.
Intel Desktop Board D955XCS Product Guide Installing DIMMs To make sure you have the correct DIMM, place the DIMM on the illustration in Figure 16 showing the DDR2 DIMM. All the notches should match with the DDR2 DIMM. DDR DDR2 mm 1 2 3 4 5 6 7 8 9 10 11 12 13 OM16943 Figure 16.
Installing and Replacing Desktop Board Components To install DIMMs, follow these steps: 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Remove the computer’s cover and locate the DIMM sockets (see Figure 17). G H I J OM17782 Figure 17. Installing a DIMM 4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. 5.
Intel Desktop Board D955XCS Product Guide Removing DIMMs To remove a memory module, follow these steps: 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. 3. Remove the AC power cord from the computer. 4. Remove the computer’s cover. 5. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops out of the socket. 6.
Installing and Replacing Desktop Board Components Installing and Removing a PCI Express x16 Card CAUTION When installing any PCI Express x16 card on the desktop board, ensure that it is fully seated in the PCI Express x16 connector before you power on the system. If the card is not fully seated in the PCI Express x16 connector, an electrical short may result across the PCI Express x16 connector pins.
Intel Desktop Board D955XCS Product Guide Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the RM: 1. Observe the precautions in "Before You Begin" on page 23. 2. Remove the screw that secures the card’s metal bracket to the chassis back panel (Figure 19, A). 3. Push back on the RM lever until the retention pin completely clears the notch in the card (Figure 19, B). 4. Pull the card straight up (Figure 19, C). A C B OM17798 Figure 19.
Installing and Replacing Desktop Board Components Connecting the IDE Cable The IDE cable can connect two drives to the desktop board. The cable supports the ATA-66/100 transfer protocol. Figure 20 shows the correct installation of the cable. NOTE ATA-66/100 compatible cables are backward compatible with drives using slower IDE transfer protocols.
Intel Desktop Board D955XCS Product Guide Connecting the Serial ATA Cable The SATA cable (4-conductor) supports the Serial ATA protocol and connects a single drive to the desktop board. For correct cable function: 1. Observe the precaution in "Before You Begin" on page 23. 2. Attach the locking cable end to the connector (Figure 21) on the board. 3. Attach the cable end without the lock to the drive (Figure 21). G H I J OM17785 Figure 21.
Installing and Replacing Desktop Board Components Connecting Internal Headers Before connecting cables to the internal headers, observe the precautions in "Before You Begin" on page 23.
Intel Desktop Board D955XCS Product Guide Front Panel Audio Header Figure 22, A on page 41 shows the location of the yellow front panel audio header. Table 5 shows the pin assignments for the front panel audio header. Table 5.
Installing and Replacing Desktop Board Components USB 2.0 Headers See Figure 22, F for the location of the black USB 2.0 headers. Table 8 shows the pin assignments for the headers. Table 8. USB 2.0 Header Signal Names USB Port A Pin USB Port B Signal Name Pin Signal Name 1 Power 2 Power 3 D- 4 D- 5 D+ 6 D+ 7 Ground 8 Ground 9 Key 10 No connect Note: USB ports may be assigned as needed.
Intel Desktop Board D955XCS Product Guide Installing the Rear Panel Hi-Speed USB 2.0 Adapter Follow these instructions to install the rear panel USB 2.0 adapter (see Figure 23): 1. Observe the precautions in "Before You Begin" on page 23. 2. Attach the cable end with the connector to the USB 2.0 header on the desktop board (see Figure 23, 1). 3. Secure the cable’s metal bracket to the chassis back panel with a screw see Figure 23, 2). 2 1 OM17787 Figure 23. Connecting the Rear Panel Hi-Speed USB 2.
Installing and Replacing Desktop Board Components Installing the Front Panel USB/IEEE 1394/Audio Solution To install the front panel USB/IEEE 1394/audio solution cables to the headers, follow these steps (see Figure 24): 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Remove the cover. 4. Locate the front panel audio header (yellow), USB 2.
Intel Desktop Board D955XCS Product Guide Connecting Fans Connecting Fans and Chassis Intrusion See Figure 25 for fan and chassis intrusion header locations. Connect the processor’s fan heat sink cable to the 4-pin processor fan header on the board. Connect chassis fan cables to the board fan headers and the chassis intrusion cable to its respective header. 1 A 1 G H 1 I 1 1 J 1 3 2 1 1 3 2 2 1 4 3 2 1 1 4 3 2 1 2 OM17789 Figure 25.
Installing and Replacing Desktop Board Components Connecting the Auxiliary Power Output Connector NOTE Do not use a Y-adapter, power splitter, or SATA power adapter to attach storage devices (such as hard disk drives or CD/DVD drives) to this connector. This connector will NOT provide adequate power for storage devices. Figure 26 shows the location of the auxiliary power output connector. G H I J OM17790 Figure 26.
Intel Desktop Board D955XCS Product Guide Connecting Power Cables NOTE Failure to use the appropriate power supply and/or not connecting the 12 V (2x4) power connector to the desktop board may result in damage to the board or the system may not function properly. See Table 3 on page 13 for power supply requirements. The 2x12 main power connector on the desktop board is backwards compatible with ATX12V power supplies with 2x10 power connections.
Installing and Replacing Desktop Board Components Connecting 2x12 Power Supply Cables If you have a 2x12 power supply, follow the instructions below. Figure 28 shows the location of the power connectors for a 2x12 power supply. G H 1 2 I OR J OM17792 Figure 28. Connecting 2x12 Power Supply Cables 1. Observe the precautions in "Before You Begin" on page 23. 2. Connect the 12 V processor core voltage power supply cable to the 2x4 connector. Use the 2x2 to 2x4 adapter if needed. 3.
Intel Desktop Board D955XCS Product Guide Other Connectors Figure 29 shows the location of the other connectors. B A D C E F G H I J G Item Description A PCI Express x1 connector B PCI bus add-in card connector 1 C PCI Express x4 connector (routed to a physical x16 connector) D PCI bus add-in card connector 2 (SMBus routed) E PCI bus add-in card connector 3 F PCI bus add-in card connector 4 G Floppy drive connector Figure 29.
Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper CAUTION Always turn off the power and unplug the power cord from the computer before changing the jumper. Moving the jumper with the power on may result in unreliable computer operation. The location of the desktop board’s BIOS configuration jumper is shown in Figure 30. 1 I 3 J OM17794 Figure 30.
Intel Desktop Board D955XCS Product Guide Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Find the configuration jumper block (see Figure 30).
Installing and Replacing Desktop Board Components Back Panel Connectors NOTE The line out connector, located on the back panel, is designed to power either headphones or amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. Figure 31 shows the back panel connectors. IEEE 1394a Line In Coaxial Line Out Optical Line Out (Toslink) OM17797 Figure 31.
Intel Desktop Board D955XCS Product Guide Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied.
Installing and Replacing Desktop Board Components AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore. PRECAUCIÓN Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo.
Intel Desktop Board D955XCS Product Guide AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. OSTRZEŻENIE Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska.
Installing and Replacing Desktop Board Components UYARI Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır. OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху. Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля. To replace the battery, follow these steps: 1.
Intel Desktop Board D955XCS Product Guide 58
3 BIOS The BIOS Setup program is accessed by pressing the key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. F2 OM17050 Figure 33. F2 Key For the latest BIOS Setup menu options, go to the Intel World Wide Web site: http://support.intel.com/support/motherboards/desktop/ Updating the BIOS The BIOS can be updated by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility.
Intel Desktop Board D955XCS Product Guide 5. Double-click the executable file from the location on your hard drive where it was saved. This runs the update program. 6. Follow the instructions provided in the dialog boxes to complete the BIOS update. Updating the BIOS with the Iflash Memory Update Utility With the Iflash BIOS update utility you can update the system BIOS from a floppy disk or other bootable media.
BIOS Recovering the BIOS It is unlikely that anything will interrupt the BIOS update; however, if an interruption occurs, the BIOS could be damaged. The following steps explain how to recover the BIOS if an update fails. The following procedure uses recovery mode for the Setup program. See page 51 for more information on Setup modes. NOTE Because of the small amount of code available in the boot block area, there is no video support. You will not see anything on the screen during this procedure.
Intel Desktop Board D955XCS Product Guide 62
4 Configuring for RAID (Intel® Matrix Storage Technology) Requires Microsoft Windows* XP or 2000 and SATA Hard Drive(s) Configuring the BIOS for Intel Matrix Storage Technology 1. Assemble your system and attach two or more SATA hard drives to the black SATA connectors. 2. Enter system BIOS Setup by pressing the key after the Power-On-Self-Test (POST) memory tests begin. 3. Go to Advanced Drive Configuration Configure SATA as; ensure RAID is selected. 4. Then save your settings by pressing .
Intel Desktop Board D955XCS Product Guide Setting Up a “RAID Ready” System The Intel Matrix Storage Technology Console software offers the flexibility to upgrade from a single Serial ATA drive to RAID without reinstalling the operating system, when a second SATA hard drive is added to the system. Follow the steps described in the headings from this section: "Configuring the BIOS for Intel Matrix Storage Technology" and "Loading the Intel Matrix Storage Technology RAID Drivers and Software".
A Error Messages and Indicators Desktop Board D955XCS reports POST errors in two ways: • By sounding a beep code • By displaying an error message on the monitor BIOS Beep Codes The BIOS beep codes are listed in Table 11. The BIOS also issues a beep code (one long tone followed by two short tones) during POST if the video configuration fails (a faulty video card or no card installed) or if an external ROM module does not properly checksum to zero. Table 11.
Intel Desktop Board D955XCS Product Guide 66
B Regulatory Compliance This appendix contains the following regulatory compliance information for Desktop Board D955XCS: • Safety regulations • European Union Declaration of Conformity statement • Product Ecology statements • Electromagnetic Compatibility (EMC) regulations • Product certification markings Safety Regulations Desktop Board D955XCS complies with the safety regulations stated in Table 13 when correctly installed in a compatible host system. Table 13.
Intel Desktop Board D955XCS Product Guide Čeština Tento výrobek odpovídá požadavkům evropských směrnic 89/336/EEC a 73/23/EEC. Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 89/336/EEC & 73/23/EEC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 89/336/EEC & 73/23/EEC. Eesti Antud toode vastab Euroopa direktiivides 89/336/EEC ja 73/23/EEC kehtestatud nõuetele. Suomi Tämä tuote noudattaa EU-direktiivin 89/336/EEC & 73/23/EEC määräyksiä.
Regulatory Compliance Product Ecology Statements The following information is provided to address worldwide product ecology concerns and regulations. Recycling Considerations As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel’s branded products to return used products to select locations for proper recycling. Please consult the http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.
Intel Desktop Board D955XCS Product Guide Français Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à des adresses spécifiées. Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.
Regulatory Compliance Russian В качестве части своих обязательств к окружающей среде, в Intel создана программа утилизации продукции Intel (Product Recycling Program) для предоставления конечным пользователям марок продукции Intel возможности возврата используемой продукции в специализированные пункты для должной утилизации. Пожалуйста, обратитесь на веб-сайт http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.
Intel Desktop Board D955XCS Product Guide EMC Regulations Desktop Board D955XCS complies with the EMC regulations stated in Table 15 when correctly installed in a compatible host system. Table 15. EMC Regulations Regulation Title FCC Class B Title 47 of the Code of Federal Regulations, Parts 2 and 15, Subpart B, Radio Frequency Devices. (USA) ICES-003 (Class B) Interference-Causing Equipment Standard, Digital Apparatus.
Regulatory Compliance Product Certification Markings (Board Level) Desktop Board D955XCS has the following product certification markings: Table 16. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel desktop boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Includes Intel name and D955XCS model designation. CE mark.
Intel Desktop Board D955XCS Product Guide 74
