Technical product specification
Table Of Contents
- Intel® NUC Board NUC5i5RYB and Intel® NUC Board NUC5i3RYB Technical Product Specification
- Revision History
- Contents
- 1 Product Description
- 1.1 Overview
- 1.2 Online Support
- 1.3 Processor
- 1.4 System Memory
- 1.5 Processor Graphics Subsystem
- 1.5.1 Integrated Graphics
- 1.5.1.1 Intel® High Definition (Intel® HD) Graphics
- 1.5.1.2 Video Memory Allocation
- 1.5.1.3 Mini High Definition Multimedia Interface* (Mini HDMI*)
- 1.5.1.4 Mini DisplayPort*
- 1.5.1.5 Multiple DisplayPort and HDMI Configurations
- 1.5.1.6 High-bandwidth Digital Content Protection (HDCP)
- 1.5.1.7 Integrated Audio Provided by the Mini HDMI and Mini DisplayPort Interfaces
- 1.5.1 Integrated Graphics
- 1.6 USB
- 1.7 SATA Interface
- 1.8 Real-Time Clock Subsystem
- 1.9 Audio Subsystem
- 1.10 LAN Subsystem
- 1.11 Hardware Management Subsystem
- 1.12 Power Management
- 2 Technical Reference
- 2.1 Memory Resources
- 2.2 Connectors and Headers
- 2.2.1 Front Panel Connectors
- 2.2.2 Back Panel Connectors
- 2.2.3 Connectors and Headers (Bottom)
- 2.3 BIOS Security Jumper
- 2.4 Mechanical Considerations
- 2.5 Electrical Considerations
- 2.6 Thermal Considerations
- 2.7 Reliability
- 2.8 Environmental
- 3 Overview of BIOS Features
- 4 Error Messages and Blink Codes
- 5 Regulatory Compliance and Battery Disposal Information
Product Description
35
1.12.2.1 Power Input
When resuming from an AC power failure, the computer returns to the power state it was in
before power was interrupted (on or off). The computer’s response can be set using the Last
Power State feature in the BIOS Setup program’s Boot menu.
1.12.2.2 Instantly Available PC Technology
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-RAM)
sleep-state. While in the S3 sleep-state, the computer will appear to be off (the power supply is
only supplying Standby power, and the front panel LED will be amber or secondary color if dual
colored, or off if single colored.) When signaled by a wake-up device or event, the system quickly
returns to its last known wake state. Table 11 on page 34 lists the devices and events that can
wake the computer from the S3 state.
The use of Instantly Available PC technology requires operating system support and drivers for
any installed M.2 add-in card.
1.12.2.3 LAN Wake Capabilities
LAN wake capabilities enable remote wake-up of the computer through a network. The LAN
subsystem monitors network traffic at the Media Independent Interface. Upon detecting a Magic
Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer.
1.12.2.4 Wake from USB
USB bus activity wakes the computer from an ACPI S3 state (not after G3)
NOTE
Wake from USB requires the use of a USB peripheral that supports Wake from USB.
1.12.2.5 WAKE# Signal Wake-up Support
When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from an ACPI S3,
S4, or S5 state.
1.12.2.6 Wake from S5
When the RTC Date and Time is set in the BIOS, the computer will automatically wake from an
ACPI S5 state.
1.12.2.7 Wake from Consumer IR
CIR activity wakes the computer from an ACPI S3, S4, or S5 state.