Intel 2804080 CoreTM Duo/Solo 945GM Mini-ITX Motherboard ® USER’S MANUAL Version 1.
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Intel® Core Duo and Intel® Core Solo processors are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction .......................................................1 Product Description............................................................. 1 Checklist.............................................................................. 2 2804080 Specifications ....................................................... 3 Board Dimensions ............................................................... 4 Installations .......................................................
IMPORTANT NOTE: When the system boots without the CRT being connected, there will be no image on screen when you insert the CRT/VGA cable. To show the image on screen, the hotkey must be pressed (CTRL-ALT-F1).
INTRODUCTION Introduction Product Description The 2804080 Mini ITX board incorporates the Mobile Intel® 945GM Express Chipset for Embedded Computing, consisting of the Intel® 945GM Graphic Memory Controller Hub (GMCH) and Intel® I/O Controller Hub 7-M (ICH7-M), an optimized integrated graphics solution with a 533MHz and 667MHz front-side bus. Dimensions of the board are 170mm x 170mm.
INTRODUCTION Checklist Your 2804080 package should include the items listed below.
INTRODUCTION 2804080 Specifications CPU Supported CPU Voltage System Speed CPU FSB Cache Green /APM CPU Socket Chipset BIOS Memory VGA SDVO (Dual CH) LVDS LCD Panel LAN USB Serial ATA Ports 1394 Parallel IDE Audio LPC I/O Digital IO Keyboard/Mouse Expansion Slots Edge Connector Onboard Header/ Connector Watchdog Timer System Voltage Others Board Size Intel® Core TM Duo /Solo processors 0.700V ~ 1.5V (IMVP-6) Up to 2.33GHz or above 533MHz/667MHz FSB 2MB APM1.
INTRODUCTION [ Board Dimensions 4 2804080 User’s Manual
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the 2804080 in order to set up a workable system. The topics covered are: Installing the CPU ........................................................................ 6 Installing the Memory .................................................................. 7 Setting the Jumpers ...................................................................... 8 Connectors on 2804080 ...............................
INSTALLATIONS Installing the CPU The 2804080 board supports a Socket 478MT processor socket for Intel® CoreTM Duo and Intel® CoreTM Solo processors The processor socket comes with a screw to secure the processor. As shown in the left picture below, loosen the screw first before inserting the processor. Place the processor into the socket by making sure the notch on the corner of the CPU corresponds with the notch on the inside of the socket. Once the processor has slide into the socket, fasten the screw.
INSTALLATIONS Installing the Memory The 2804080 board supports two DDR2 memory socket for a maximum total memory of 4GB in DDR2 memory type. Installing and Removing Memory Modules To install the DDR2 modules, locate the memory slot on the board and perform the following steps: 1. Hold the DDR2 module so that the key of the DDR2 module align with those on the memory slot. 2.
INSTALLATIONS Setting the Jumpers Jumpers are used on 2804080 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on 2804080 and their respective functions. Jumper Locations on 2804080........................................................ 9 JP5: LCD Panel Power Selection.................................................. 10 JP6: 1394 EPROM Write Selection..
INSTALLATIONS Jumper Locations on 2804080 Jumpers on 2804080...........................................................................Page JP5: LCD Panel Power Selection ................................................. 10 JP6: 1394 EPROM Write Selection ............................................. 10 JP7: Clear CMOS Setting ............................................................. 10 JP8: CompactFlash Slave/Master Selection .................................
INSTALLATIONS JP5: LCD Panel Power Selection JP3 LCD Panel Power 3.
INSTALLATIONS Connectors on 2804080 The connectors on 2804080 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on 2804080 and their respective functions. CN1: PS/2 Keyboard and PS/2 Mouse Connectors...................... 13 CN2, CN3: COM1 and VGA Connector...................................... 13 CN4: 10/100 RJ-45 and USB1/2 Ports ......................................... 14 CN5: 1394 Connector............
INSTALLATIONS Connector Locations on 2804080 12 2804080 User’s Manual
INSTALLATIONS CN1: PS/2 Keyboard and PS/2 Mouse Connectors PS/2 Mouse PS/2 Keyboard Signal Name Keyboard data N.C. GND 5V Keyboard clock N.C. Keyboard 1 2 3 4 5 6 Mouse 1 2 3 4 5 6 Signal Name Mouse data N.C. GND 5V Mouse clock N.C. CN2, CN3: COM1 and VGA Connector Signal Name Pin # DCD 1 RXD 2 TXD 3 DTR 4 GND 5 [ Pin # Signal Name 6 DSR 7 RTS 8 CTS 9 RI 10 Not Used [[[[ Signal Name Red Blue GND GND N.C. N.C. HSYNC NC Pin # 1 3 5 7 9 11 13 15 2804080 User’s Manual Pin # Signal Name 2 Green 4 N.C.
INSTALLATIONS CN4: 10/100 RJ-45 and USB1/2 Ports CN5: 1394 Connector J12: SPDIF Out Connector CN6: GbE RJ-45 and USB3/4 Ports CN8: Audio Connector The audio connector, from top to bottom, is composed of Line in, Line out and Microphone jacks. CN9, CN10: Serial ATA Connectors FAN1: System Fan Power Connector FAN1 is a 3-pin header for system fans. The fan must be a 12V (500mA). Pin # 1 2 3 Signal Name Ground +12V Rotation detection FAN2: CPU Fan Power Connector FAN2 is a 3-pin header for the CPU fan.
INSTALLATIONS IDE1: IDE Connector Signal Name Reset IDE Host data 7 Host data 6 Host data 5 Host data 4 Host data 3 Host data 2 Host data 1 Host data 0 Ground DRQ0 Host IOW Host IOR IOCHRDY DACK0 IRQ14 Address 1 Address 0 Chip select 0 Activity Pin # 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Pin # 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal Name Ground Host data 8 Host data 9 Host data 10 Host data 11 Host data 12 Host data 13 Host data 14 Host data 15 Protect pin Ground
INSTALLATIONS J14: ATX Power Supply Connector 11 1 20 10 Signal Name 3.3V -12V Ground PS-ON Ground Ground Ground -5V +5V +5V Pin # 11 12 13 14 15 16 17 18 19 20 Pin # 1 2 3 4 5 6 7 8 9 10 Signal Name 3.3V 3.
INSTALLATIONS J3: System Function Connector J3 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. J3 is a 20-pin header that provides interfaces for the following functions. Hard Disk Drive LED Reset Switch Not Defined ATX Power On Switch Not Defined Power LED Speaker Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended.
INSTALLATIONS Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header. Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.
INSTALLATIONS J6: USB5/6 Port Pin Header Signal Name Pin Vcc 1 D2 D+ 3 Ground 4 Pin 5 6 7 8 Signal Name Ground D+ DVcc J7: COM2 Serial Port COM2 Signal Name DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground Pin # 1 2 3 4 5 Pin # 6 7 8 9 10 Signal Name DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used J8: Wake On LAN Connector J8 is a 3-pin header for the Wake On LAN function.
INSTALLATIONS J9, J10: LVDS Connectors (1st channel, 2nd channel) The LVDS connectors on board consist of the first channel (J9) and second channel (J10) and supports 18-bit or 36-bit. Signal Name TX0Ground TX15V/3.3V NA TX2Ground TXC5V/3.
INSTALLATIONS J16: 1394 Connector Signal Name Pin TPA+ 1 TPA3 +DV5 5 GND 7 Pin 2 4 6 8 Signal Name TPB+ TPBNC NC J17: Front Audio Connector Signal Name Pin Pin Signal Name 5 6 7 8 Rear Audio L Front Audio L VREF Out Rear Audio R Front Audio R Mic In Ground 1 2 3 4 REMARKS: To use the front audio connector, the jumpers on pin 1-3 and pin 2-4 must be removed.
INSTALLATIONS CON1: SDVO Port Connector 22 Signal Name Pin # Pin # Signal Name +12V +12V +5V 3.3V RESET GND SDVOC_CLK+ SDVOC_Blue+ GND SDVOC_Green+ SDVOC_Red+ GND SDVO TVClkIn+ SDVOB Int+ GND SDVO CtrlData SDVOB Clk+ GND SDVOB Blue+ SDVOB Green+ GND SDVOB Red+ SDVO Stall+ GND A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 +12V +12V +5V 3.
INSTALLATIONS Headers and Connectors on 2804080 Daughter Cards ID390 JP4 LCD Panel Power Selection JP4 Voltage 3.3V 5V ID390 J1 LCD Backlight Setting Pin # 1 2 3 ID390 Signal Name +12V Backlight Enable Ground J3 and J2 1st/2nd LVDS Channel Connectors Signal Name TX0Ground TX15V/3.3V TX3TX2Ground TXC5V/3.
INSTALLATIONS ID390C J4 VGA Connector [[[[ Signal Name +5V Ground N.C. SDA HSYNC VSYNC SCL N.C. 24 Pin # 2 4 6 8 10 12 14 16 Pin # Signal Name 1 RED 3 GREEN 5 BLUE 7 N.C.
INSTALLATIONS ID391 J2 DVI Connector Signal Name TDC1Ground TLC+5V NC TDC2Ground TDC0NC DDC_SC ID391D Pin # 2 4 6 8 10 12 14 16 18 20 Pin # 1 3 5 7 9 11 13 15 17 19 Signal Name TDC1+ Ground TLC+ Ground HPDET TDC2+ Ground TDC0+ NC DDC_SD J1, J2 1st/2nd DVI Connectors Signal Name TDC1Ground TLC+5V NC TDC2Ground TDC0NC DDC_SC Pin # 2 4 6 8 10 12 14 16 18 20 Pin # 1 3 5 7 9 11 13 15 17 19 Signal Name TDC1+ Ground TLC+ Ground HPDET TDC2+ Ground TDC0+ NC DDC_SD Remarks: When using dual DVI, the first DV
INSTALLATIONS This page is intentionally left blank.
BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction ........................................................................ 28 BIOS Setup................................................................................... 28 Standard CMOS Setup ................................................................. 30 Advanced BIOS Features ..................................
BIOS SETUP BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit F10 : Save & Exit Setup Ç È Æ Å : Select Item Time, Date, Hard Disk Type The section below the setup items of the Main Menu displa
BIOS SETUP Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
BIOS SETUP To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time. Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the / or +/- keys to set the current time. IDE Channel Master/Slave The onboard PCI IDE connector provides Primary and Secondary channels for connecting up to two IDE hard disks or other IDE devices. Press to configure the hard disk.
BIOS SETUP Video This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt On This field determines whether or not the system will halt if an error is detected during power up. No errors The system boot will not be halted for any error that may be detected.
BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items. First/Second/Third Boot Device These fields determine the drive that the system searches first for an operating system. The options available include Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-Floppy, USB-ZIP, USB-CDROM, LAN and Disable.
BIOS SETUP Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. Security Option This field allows you to limit access to the System and Setup. The default value is Setup. When you select System, the system prompts for the User Password every time you boot up.
BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset.
BIOS SETUP DRAM RAS# Precharge This option sets the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes. The default setting for the Active to Precharge Delay is 4. Precharge Delay (tRAS) The default setting for the Precharge Delay is 12. System Memory Frequency The default setting is 533MHz. SLP_S4# Assertion Width The default setting is 1 to 2 Sec.
BIOS SETUP Panel Scaling The default setting is Auto. The options available include On and Off. Panel Number These fields allow you to select the LCD Panel type. The default values for these ports are: 640x480 800x480 800x600 1024x768 1280x1024 1280x768 1400x1050 1600x1200 18bit 18bit 18bit 18bit 18bit 18bit 18bit 18bit SC SC SC SC DC SC DC DC Onboard PCI-E LAN By default, this setting is enabled. LAN PXE Option ROM By default, this setting is disabled.
BIOS SETUP Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main items for user to select. Once an item selected, a submenu appears. Details follow.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility SuperIO Device POWER ON Function KB Power ON Password Hot Key power ON Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD , TxD Active IR Transmission Delay UR2 Duplex Mode Use IR Pins PWRON After PWR-Fail BUTTON ONLY Enter Ctrl-F1 Enabled 3F8/IRQ4 2F8/IRQ3 Normal Hi, Lo Disabled Half IR-Rx2Tx2 Off ITEM HELP Menu Level > IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to trans
BIOS SETUP On-Chip Serial ATA Setting The fields under the SATA setting includes On-Chip Serial ATA (Auto), PATA IDE Mode (Secondary) and SATA Port (PO, P2 is Primary). USB Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. USB 2.0 Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. In order to use USB 2.0, necessary OS drivers must be installed first.
BIOS SETUP Onboard Serial Port These fields allow you to select the onboard serial ports and their addresses. The default values for these ports are: Serial Port 1 3F8/IRQ4 Serial Port 2 2F8/IRQ3 UART Mode Select This field determines the UART 2 mode in your computer. The default value is Normal. Other options include IrDA and ASKIR. PWRON After PWR-Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation.
BIOS SETUP Power Management Setup Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function ACPI Suspend RUN VGABIOS if S3 Resume Power Management Video Off Method Off In Suspend Type Modem Use IRQ Enabled S1(POS) Auto User Define DPMS Video Yes Suspend Stop Grant 3 Suspend Mode HDD Power Down Soft-Off by PWR-BTTN Wake-Up by PCI Card Power On by Ring Resume by Alarm Date (of Month) Alarm Time (hh:mm:ss) Alarm Disabled Disabled Instant-Off Disabled Disabled Disabled 0 0:0:0 ** Reload G
BIOS SETUP Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows BIOS to control the video display. Blank Screen Writes blanks to the video buffer. Video Off In Suspend When enabled, the video is off in suspend mode. The default setting is Yes. Suspend Type The default setting for the Suspend Type field is Stop Grant.
BIOS SETUP Resume by Alarm This field enables or disables the resumption of the system operation. When enabled, the user is allowed to set the Date and Time. Reload Global Timer Events The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events that can prevent the system from entering a power saving mode or can awaken the system from such a mode. When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur.
BIOS SETUP PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Shutdown Temperature CPU Warning Temperature Current System Temp Current CPU Temp System FAN Speed CPU FAN Speed Vcore(V) 12 V 1.8V Disabled Disabled 45°C/113°F 45°C/113°F 5400 RPM 5400 RPM 1.02 V 1.32 V 1.8V -5V +5V -12V 3.3V -5.02V 5.25 V -12.59 3.37V VBAT (V) 3.
BIOS SETUP Frequency/Voltage Control This section shows the user how to configure the processor frequency. Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI Clk Disabled Spread Spectrum Modulated Disabled ITEM HELP Menu Level > Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock. Spread Spectrum Modulated This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only.
BIOS SETUP Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. Load Optimized Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. Set Supervisor Password These two options set the system password.
BIOS SETUP This page is intentionally left blank.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 2000 and Windows XP. The software and drivers are included with the motherboard. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel Chipset Software Intallation Utility ................................... 52 VGA Drivers Installation .................................................
DRIVER INSTALLATION Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 2000/XP. 1. Insert the CD that comes with the board. Click Intel Chipsets and then Intel(R) I945GMChipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility. 3.
DRIVERS INSTALLATION 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVER INSTALLATION VGA Drivers Installation To install the VGA drivers, follow the steps below to proceed with the installation. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) I945GMChipset Drivers. 2. Click Intel(R) I945GMChipset Family Graphics Driver. 3. When the Welcome screen appears, click Next to continue.
DRIVERS INSTALLATION 4. Click Yes to to agree with the license agreement and continue the installation. 5. Restart the computer as promted and for changes to take effect. IMPORTANT NOTE: When you have restarted the computer, your computer screen will be blank. At this point, press CTRL-ALT-F1 simultaneously, if you are using CRT monitor. If you are using LVDS LCD panel, press CTRL-ALT-F3. If you are using DVI monitor, press CTRL-ALT-F4.
DRIVER INSTALLATION AC97 Codec Audio Driver Installation Follow the steps below to install the Realtek AC97 Codec Audio Drivers. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) I945GMChipset Drivers. 2. Click Realtek AC'97 Codec Audio Driver. 3. Click Finish to restart the computer and for changes to take effect. .
DRIVERS INSTALLATION LAN Drivers Installation Follow the steps below to complete the installation of the Intel PRO LAN drivers. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) I945GMChipset Drivers, then Intel(R) PRO LAN Network Drivers. 2. Click Install Base Software to continue. 3. When prompted, please to restart the computer for new settings to take effect.
DRIVER INSTALLATION Follow the steps below to install the Marvell Gigabit LAN drivers. 1. Insert the CD that comes with the motherboard. Click LAN Card and then Marvell LAN Controller Driver. 2. Click Next when the InstallShield Wizard welcome screen appears. 3. Click Next to agree with the license agreement. 4. Click Next when the Readme Information screen appears to proceed with the drives installation process. 5. When the Installation is complete, click Finish for the changes to take effect.
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.
APPENDIX C. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
APPENDIX void copyright(void) { printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO DETECT) ========\n"\ " Usage : W627E_WD reset_time\n"\ " Ex : W627E_WD 3 => reset system after 3 second\n"\ " W627E_WD 0 => disable watch dog timer\n"); } //=========================================================================== void EnableWDT(int interval) { unsigned char bBuf; bBuf = Get_W627EHF_Reg( 0x2D); bBuf &= (!0x01); Set_W627EHF_Reg( 0x2D, bBuf); //Enable WDTO Set_W627EHF_LD( 0x08); Set_W627EHF_Reg( 0
APPENDIX //=========================================================================== // // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //=========================================================================== #include "W627EHF.H" #include
APPENDIX //=========================================================================== void Set_W627EHF_Reg( unsigned char REG, unsigned char DATA) { Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, REG); outportb(W627EHF_DATA_PORT, DATA); Lock_W627EHF(); } //=========================================================================== unsigned char Get_W627EHF_Reg(unsigned char REG) { unsigned char Result; Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, REG); Result = inportb(W627EHF_DATA_PORT); Lock_W627EHF();
Any advice or comments about our products and service, or anything we can help you with please don t hesitate to contact with us. We will do our best to support you for your products, projects and business Global American Inc. Address 17 Hampshire Drive Hudson, NH 03051 TEL Toll Free (U.S. Only) 800-833-8999 (603)886-3900 FAX (603)886-4545 Website http://www.globalamericaninc.com E-Mail salesinfo@globalamericaninc.
