C ompact Board P CM -6892 Rev.B PCM-6892 Rev.B Intel® ULV Celeron® 400 / 650 MHz Processor Compact Board With LCD, Ethernet, TV-Out, Mini PCI, Speaker out PCM-6892 Rev. B Manual 4th Ed.
C ompact Board P CM -6892 Rev.B Copyright Notice This document is copyrighted, 2005. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
C ompact Board P CM -6892 Rev.B Acknowledgments All other products’name or trademarks are properties of their respective owners. l Award is a trademark of Award Software International, Inc. l CompactFlash™ is a trademark of the Compact Flash Association. l Intel® , Pentium® and Celeron® are trademarks of Intel® Corporation. l Microsoft Windows is a registered trademark of Microsoft Corp. l ITE is a trademark of Integrated Technology Express, Inc.
C ompact Board P CM -6892 Rev.B Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-6892 Rev. B CPU Card • 1 Jumper cap • 1 Quick Installation Guide • 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
C ompact Board P CM -6892 Rev.B Contents Chapter 1 General Information 1.1 Introduction............................................................................ 1-2 1.2 Features................................................................................... 1-4 1.3 Specifications........................................................................... 1-5 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ................................................................... 2-2 2.
C ompact Board P CM -6892 Rev.B 2.18 LAN1 LED Connector (CN8).............................................2-16 2.19 LAN2 LED Connector (CN9).............................................2-17 2.20 Audio Connector (CN10) ....................................................2-17 2.21 COM1~4 Connector (CN11) ..............................................2-18 2.22 USB Connector (CN12).......................................................2-19 2.23 USB Connector (CN13).............................................
C ompact Board P CM -6892 Rev.B 3.15 Exit without saving ............................................................... 3-8 Chapter 4 Driver Installation 4.1 Step 1 – Install VIA 4 in 1 Driver........................................... 4-3 4.2 Step 2 – Install Graphic Driver............................................... 4-3 4.3 Step 3 – Install Audio Driver.................................................. 4-3 4.4 Step 4 – Install Ethernet Driver.............................................. 4-4 4.
C ompact Board P CM -6892 Rev.
C ompact Board P CM -6892 Rev.B 1.1 Introduction PCM-6892 Rev. B is the extension of PCM-6892 Rev. A. This model possess all features in Rev. A but the only difference Intel® Ultra Low Voltage Celeron® 400/650MHz processor was introduced into Rev. B. With the processor, PCM-6892 Rev. B will own more excellent performance and lower power consumption than PCM-6892 Rev. A. More options for your extension Compared with PCM-6892 Rev. A, the new PCM-6892 Rev. B owns Mini PCI slot.
C ompact Board P CM -6892 Rev.B expand interface will be the best choice for the embedded application which has the severe condition for the space and environment.
C ompact Board P CM -6892 Rev.B 1.
C ompact Board P CM -6892 Rev.B 1.3 Specifications System l CPU: Onboard Intel® Ultra Low Voltage Celeron® 400 /650MHz Processor l Memory: Onboard one 168-pin DIMM socket support up to 512MB SDRAM l Chipset: VIA VT8606 / VT82C686B l BIOS: Award 256KB Flash BIOS l Enhanced IDE: Supports up to two IDE devices. Support Ultra DMA100 mode with transfer rate up to 100MB / sec. l FDD Interface: Support up to two floppy disk drives, 5.25 inch (360KB and 1.2 MB) and/or 3.5 inch (720KB, 1.
C ompact Board P CM -6892 Rev.B A 7(4 x 2-1) pin header support PC/AT keyboard and PS/2 mouse. l USB connector: Support four USB 1.1 ports l Battery: Lithium battery for data retention l Watchdog timer: Can generate a system reset. l Power Management: Support ATX or AT power supply. Support power saving standby modes.
C ompact Board P CM -6892 Rev.B I/O l MIO: IDE (UDMA33) x 1, FDD x 1, KB + Mouse x 1, RS-232 x 3, RS-232/422/485 x 1, Parallel x 1 l IrDA: One IrDA Tx/Rx header l Audio: VIA VT82C686B with AC-97 2.0 compliant audio codec VT1612 l USB: Two 5x2 pin headers support 4 USB 1.
C o m p a c t Board PCM-6892 Rev.B 2 Chapter Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
Compact Board PCM-6892 Rev.B 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
C o m p a c t Board PCM-6892 Rev.B 2.
Compact Board Chapter 2 Quick Installation Guide 2 - 4 PCM-6892 Rev.
C o m p a c t Board PCM-6892 Rev.B 2.
Compact Board Solder Side Chapter 2 Quick Installation Guide 2 - 6 PCM-6892 Rev.
C o m p a c t Board PCM-6892 Rev.B 2.4 List of Jumpers There are a number of jumpers in the board that allow you to configure your system to suit your application.
Compact Board PCM-6892 Rev.B 2.5 List of Connectors There are a number of connectors in the board that allow you to configure your system to suit your application.
C o m p a c t Board PCM-6892 Rev.
Compact Board PCM-6892 Rev.B 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
C o m p a c t Board PCM-6892 Rev.B 2.7 Audio Out Selection (JP1) JP1 Function 1-3, 2-4 W/O Amplifier 3-5, 4-6 W/ Amplifier (Default) 2.8 LCD Voltage Selection (JP2) JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.
Compact Board PCM-6892 Rev.B 2.10 Clear CMOS (JP4) JP4 Function 1-2 Protected (Default) 2-3 Clear 2.11 COM2 Ring/+5V/+12V Selection (JP5) JP5 Function 1-2 +12V 3-4 +5V 5-6 Ring (Default) 2.12 TV-Out Connector (CN1) Pin 1 Signal Y Pin 2 Signal CVBS 3 GND 4 GND 5 C 6 N.C. 7 GND 8 N.C.
C o m p a c t Board PCM-6892 Rev.B 2.
Compact Board PCM-6892 Rev.B 2.14 VGA Display Connector (CN4) Pin 1 Signal RED Pin 2 Signal VGAVCC 3 GREEN 4 GND 5 BLUE 6 N.C. 7 N.C. 8 SDATA 9 GND 10 H 11 GND 12 V 13 GND 14 SCLK 15 GND 16 N.C. 2.15 ATX Power Connector (CN5) Pin Signal 1 +3.3V Pin Signal 11 +3.3V 2 +3.
C o m p a c t Board PCM-6892 Rev.B 2.16 TTL_LCD Connector (CN6) Pin Signal 1 +5V Pin Signal 2 +5V 3 GND 4 GND 5 +3.3V 6 +3.3V 7 ENBKL 8 GND 9 BLUE0 10 BLUE1 11 BLUE2 12 BLUE3 13 BLUE4 14 BLUE5 15 BLUE6 16 BLUE7 17 GREEN0 18 GREEN1 19 GREEN2 20 21 GREEN4 22 GREEN3 GREEN GREEN5 23 GREEN6 24 GREEN7 25 RED0 26 RED1 27 RED2 28 RED3 29 RED4 30 RED5 31 RED6 32 RED7 33 GND 34 GND 35 DOT_CLOCK 36 VSYNC 37 DE 38 HSYNC 39 N.C.
Compact Board PCM-6892 Rev.B 2.17 LVDS Connector (CN7) Pin 1 Signal ENBKL Pin 2 Signal BKLCTL 3 PPVCC 4 GND 5 LVDS_CH1_TXCLK- 6 LVDS_CH1_TXCLK+ 7 PPVCC 8 GND 9 LVDS_CH1_TX0- 10 LVDS_CH1_TX0+ 11 LVDS_CH1_TX1- 12 LVDS_CH1_TX1+ 13 LVDS_CH1_TX2- 14 LVDS_CH1_TX2+ 15 N.C. 16 N.C. 17 I2C_DATA 18 I2C_CLK 19 LVDS_CH2_TX0- 20 LVDS_CH2_TX0+ 21 LVDS_CH2_TX1- 22 LVDS_CH2_TX1+ 23 LVDS_CH2_TX2- 24 LVDS_CH2_TX2+ 25 N.C. 26 N.C.
C o m p a c t Board PCM-6892 Rev.B 2.19 LAN2 LED Connector (CN9) Pin 1 Signal RX LED Pin 2 Signal +3.3V 3 Link LED 4 +3.3V 5 TX LED 6 +3.3V 2.20 Audio Connector (CN10) Pin 1 Signal MIC_IN Pin 2 Signal MIC_+2.
Compact Board PCM-6892 Rev.B 2.21 COM1~4 Connector (CN11) Pin 1 Signal DCD1 Pin 2 Signal DSR1 3 RXD1 4 RTS1 5 TXD1 6 CTS1 7 DTR1 8 RI1 9 GND 10 N.C. 11 DCD2 (422TXD-/485DATA-) 12 DSR2 13 RXD2 (422RXD+) 14 RTS2 15 TXD2 (422TXD+/485DATA+) 16 CTS2 17 DTR2 (422RXD-) 18 RI2/+12V/+5V 19 GND 20 N.C. 21 DCD3 22 DSR3 23 RXD3 24 RTS3 25 TXD3 26 CTS3 27 DTR3 28 RI3 29 GND 30 N.C.
C o m p a c t Board PCM-6892 Rev.B 2.22 USB Connector (CN12) Pin 1 Signal +5V Pin 2 Signal GND 3 USBD0- 4 GND 5 USBD0+ 6 USBD1+ 7 GND 8 USBD1- 9 GND 10 +5V 2.23 USB Connector (CN13) Pin 1 Signal +5V Pin 2 Signal GND 3 USBD2- 4 GND 5 USBD2+ 6 USBD3+ 7 GND 8 USBD3- 9 GND 10 +5V 2.24 IrDA Connector (CN14) Pin 1 Signal +5V 2 N.C.
Compact Board PCM-6892 Rev.B 2.25 Fan Connector (CN15) Pin 1 Signal Speed Sense 2 +5V 3 GND 2.26 PS/2 Keyboard & Mouse Connector (CN16) Pin 1 Signal Keyboard DATA Pin 2 Signal Keyboard CLOCK 3 Keyboard GND 4 Keyboard VCC 5 Mouse DATA 6 Mouse CLOCK 7 N.C. 8 N.C. 2.
Compact Board PCM -6892 Rev.
Compact Board PCM -6892 Rev.B 3.1 System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Compact Board PCM -6892 Rev.B 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Compact Board PCM -6892 Rev.B This menu shows you the status of PC. Frequency/Voltage Control This menu shows you the display of frequency/Voltage Control. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Compact Board PCM -6892 Rev.B 3.3 Standard CMOS Features This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the right box of the Menu screen. 3.4 Advanced BIOS Features This sample screen contains the manufacturer’s default values for the PCM-6892 REV.B 3.
Compact Board PCM -6892 Rev.B 3.6 Integrated Peripherals This sample screen contains the manufacturer’s default values for the PCM-6892 REV.B. PCMCIA Card Support Limitation List of PCM-6892 Rev.B COM 3 and 4 need to be disable for supporting 16bit PCMCIA Card under Windows 98 SE and Windows 2000 at both ACPI and APM mode To disable COM3 and COM4 for supporting 16bit PCMCIA cards, please enable the PCMCIA SERIQR option in CMOS setting.
Compact Board PCM -6892 Rev.B 3.7 Power management Setup This sample screen contains the manufacturer’s default values for the PCM-6892 REV.B. 3.8 PnP/PCI configuration This sample screen contains the manufacturer’s default values for the PCM-6892 REV.B. 3.9 PC Health Status This sample screen contains the manufacturer’s default values for the PCM-6892 REV.B. 3.10 Frequency/Voltage control This sample screen contains the manufacturer’s default values for the PCM-6892 REV.B. 3.
Compact Board PCM -6892 Rev.B 3.13 Set Supervisor/User Password You can set either SUPERVISOR or USER PASSWORD, or both of them. The difference between the two is that the supervisor password allows unrestricted access to enter and change the options of the setup menus, while the user password only allows entry to the program, but not modify options. To abort the process at any time, press Esc.
Compact Board PCM-6892 Rev.
Compact Board PCM-6892 Rev.B The PCM-6892 Rev.B comes with a CD-ROM that contains all drivers and utilities that you need for setup the system. Follow the sequence below to install the drivers: Step 1 – Install VIA 4 in 1 driver Step 2 – Install Graphic Driver Step 3 – Install Audio Driver Step 4 – Install Ethernet Driver Step 5 – Install PCMCIA Driver (Win98 only) Please read instructions below for further detailed installations. Insert the PCM-6892 Rev.B CD-ROM into the CD-ROM Drive.
Compact Board PCM-6892 Rev.B 4.1 Step 1 – Install VIA 4 in 1 for Windows 98SE/2000/XP 1. Double click on the “executive file”. 2. Follow the instructions that the window will show you. 3. The system will help you install the driver automatically. 4.2 Step 2 – Install Graphic Driver for Windows 98SE/2000/XP 1. Choose the folder according to the OS you used and then double click on the “Setup.exe” file. 2. Follow the instructions that the window will show you. 3.
Compact Board PCM-6892 Rev.B 4.4 Step 4 – Install Ethernet Driver for Windows 98SE /2000/XP 1. Double click on the “Setup.exe” file. 2. Follow the instructions that the window will show you. 3. The system will help you install the driver automatically. 4.5 Step 5 – Install AAEON PCMCIA Driver for Windows 98SE 1. Double click on the “TiSetup.exe” file. 2. Follow the instructions that the window will show you. 3. The system will help you install the driver automatically.
Compact Board PCM-6892 Rev.
Compact Board PCM-6892 Rev.B A.
Compact Board PCM-6892 Rev.B A.3 IRQ Mapping Chart IRQ0 System Timer IRQ8 IRQ1 Keyboard IRQ9 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 Cascade to IRQ Controller COM2 COM1 Unused Floppy Disk Controller Printer System CMOS / Real time clock Microsoft ACPI – Compliant system COM3 COM4 PS/2 mouse FPU Primary IDE Secondary IDE A.
C ompact Board P CM -6892 Rev.
C ompact Board P CM -6892 Rev.B B.1 Programming the Watchdog Timer PCM-6892 contains a watchdog timer reset pin. (GP16) All reference material can be found on the following pages.
C ompact Board P CM -6892 Rev.B ==================================================** ** Title : WatchDog Timer Setup Utility (for W83977 GP16) ** ** Company : AAEON Technology Inc. ** ** Compiler : Borland C ++ Version 3.0 ** **=================================================== ===========*/ #include #include #include #include #include #include
C ompact Board P CM -6892 Rev.
C ompact Board P CM -6892 Rev.
C ompact Board P CM -6892 Rev.
C ompact Board P CM -6892 Rev.B //Set Register 2B (PIN 58) Bit 0 = 0/1 (KBLOCK/GP13) //set to GP13 for WD Rst WriteAData(0x2B,ReadAData(0x2B)|0x01); } else if(watch_dog_output_GP==16) { //Set Register 2C (PIN 119) Bit 5 -4 = 01 (GP16) //set to GP16 for WD Rst WriteAData(0x2C,ReadAData(0x2C)|0x10); } //Exit W83977 Configure mode ExitConfigMode(); } void main(int argc, char* argv[]) { int time_value=0; char *ptr; printf( inBond 83977 WatchDog Timer Setup Utility w Version 1.
C ompact Board P CM -6892 Rev.
