Product Data Sheet / Brochure
Table Of Contents
- 1 Product Description
- 1.1 Overview
- 1.2 Online Support
- 1.3 Processor
- 1.4 System Memory
- 1.5 Processor Graphics Subsystem
- 1.5.1 Integrated Graphics
- 1.5.1.1 Intel® Ultra High Definition (Intel® UHD) Graphics
- 1.5.1.2 Video Memory Allocation
- 1.5.1.3 High Definition Multimedia Interface* (HDMI*)
- 1.5.1.4 DisplayPort* via USB Type-C
- 1.5.1.5 Multiple DisplayPort and HDMI Configurations
- 1.5.1.6 High-bandwidth Digital Content Protection (HDCP)
- 1.5.1.7 Integrated Audio Provided by the HDMI and USB Type C Interfaces
- 1.5.1 Integrated Graphics
- 1.6 USB
- 1.7 SATA Interface
- 1.8 Thunderbolt 3
- 1.9 Real-Time Clock Subsystem
- 1.10 Audio Subsystem†
- 1.11 LAN Subsystem
- 1.12 Hardware Management Subsystem
- 1.13 Power Management
- 1.14 Intel Platform Security Technologies
- 2 Technical Reference
- 2.1 Memory Resources
- 2.2 Connectors and Headers
- 2.2.1 Front Panel Connectors
- 2.2.2 Back Panel Connectors
- 2.2.3 Headers and Connectors (Top)
- 2.2.4 Connectors and Headers (Bottom)
- 2.2.4.1 Signal Tables for the Connectors and Headers
- 2.2.4.2 Add-in Card Connectors
- 2.2.4.3
- 2.2.4.4 USB Type C connector
- 2.2.4.5 Front Panel Header (2.0 mm Pitch)
- 2.2.4.6 SDXC Card Reader
- 2.2.4.7 Power Supply Connector
- 2.2.4.8 Internal USB 2.0 Single-Port Header (1.25 mm Pitch)
- 2.2.4.9 Consumer Infrared (CIR) Sensor
- 2.2.4.10 Consumer Electronics Control (CEC) Header
- 2.2.4.11 RGB LED
- 2.2.4.12 Digital Microphone Array†
- 2.3 BIOS Security Jumper
- 2.4 Mechanical Considerations
- 2.5 Electrical Considerations
- 2.6 Thermal Considerations
- 2.7 Reliability
- 2.8 Environmental
- 3 Overview of BIOS Features
- 4 Error Messages and Blink Codes
- 5 Intel NUC Kit Features
Technical Reference
29
Figure 13. Connection Diagram for Front Panel Header (2.0 mm Pitch)
2.2.4.5.1 Hard Drive Activity LED Pins
Pins 1 and 3 can be connected to an LED to provide a visual indicator that data is being read from
or written to a hard drive. Proper LED function requires a SATA hard drive or optical drive
connected to an onboard SATA connector.
2.2.4.5.2 Reset Switch Pins
Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is
normally open. When the switch is closed, the board resets and runs the POST.
2.2.4.5.3 Power/Sleep LED Pins
Pins 2 and 4 can be connected to a one- or two-color LED. Table 22 and Table 23 show the
possible LED states.
Table 22. States for a One-Color Power LED
LED State
Description
Off
Power off
Blinking
Standby
Steady Normal operation
Table 23. States for a Dual-Color Power LED
LED State
Description
Off
Power off
Secondary color blinking
(amber)
Standby
Primary color steady (Blue)
Normal operation
NOTE
The LED behavior shown in Table 22 is default – other patterns may be set via BIOS setup.