User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Intel® NUC Kit NUC10i7FNKN Intel® NUC Kit NUC10i5FNKN Intel® NUC Kit NUC10i3FNKN User Guide 1
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Before You Begin CAUTIONS The steps in this guide assume you’re familiar with computer terminology and with the safety practices and regulatory compliance required for using and modifying computer equipment. Disconnect the computer from its power source and from any network before performing any of the steps described in this guide.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN This guide tells you how to: • • • • • • Install and remove memory Install an M.2 SSD Install a VESA mount bracket Connect power Install an operating system Install the latest drivers Open the Chassis Unscrew the four corner screws on the bottom of the chassis and lift the cover. Installing and Removing Memory Intel NUC Kits NUC10i7FNKN, NUC10i5FNKN and NUC10i3FNKN have two 260-pin DDR4 SO-DIMM sockets. Memory requirements: 1.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Install SO-DIMMs If you plan to install just one SO-DIMM, install it in the lower memory socket. To install the SO-DIMMs, follow these steps: 1. Observe the precautions in "Before You Begin" on page 2. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. 4. 5. Align the small notch at the bottom edge of the SO-DIMM with the key in the socket.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Install an M.2 SSD Intel NUC Kits NUC10i7FNKN, NUC10i5FNKN and NUC10i3FNKN support 80mm and 42mm SSDs. Find compatible M.2 SSDs at the Intel® Product Compatibility Tool: NUC10i7FNKN NUC10i5FNKN NUC10i3FNKN NOTE Before changing the Intel Optane memory module, it needs to be disabled. Follow Removing Intel Optane Memory on this page first, before taking the module out. If you’re installing an 80mm M.2 SSD: 1.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Close the Chassis After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by hand with a screwdriver to avoid over-tightening and possibly damaging the screws. Attach and Use the VESA Bracket (Optional) Follow these instructions to attach and use the VESA mount bracket: 1. 6 Using the four small black screws that were included in the box, attach the VESA bracket to the back of the monitor or TV.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN 7 2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC. 3. Slide the Intel NUC onto the VESA mount bracket.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Connect Power Country-specific power cords are included in the Intel NUC Kit box. Connect AC power Each Intel NUC model includes either a region-specific AC power cord or no AC power cord (only the power adapter). Product codes Power cord type The connector on the power adapter is a C5 type connector. BXNUC10i7FNKN1, BXNUC10i5FNKN1, BXNUC10i3FNKN1, BXNUC10i7FNKN2, BXNUC10i5FNKN2, BXNUC10i3FNKN2 US power cord included. EU power cord included.
User Guide for NUC10i7FNKN, NUC10i5FNKN, NUC10i3FNKN Install Intel NUC Drivers To download the latest Microsoft* Windows* drivers and BIOS updates, go to Download Center: Links: NUC10i7FNKN NUC10i5FNKN NUC10i3FNKN Drivers are available for the following features: 9 Chipset Graphics Intel® Management Engine Wireless and/or Gigabit Ethernet (depending on how you connect) Bluetooth®—required if you use Bluetooth devices Thunderbolt Consumer Infrared (CIR)—required if you use an i
