EXHIBIT C – User Manual FCC ID O2Z-BT2
Eligibility Requirements for Regulatory Module Approval Introduction The Intel Personal Wireless Module(Ambler) with Bluetooth wireless technology is a radio device that transmits and receives radio signals in accordance with the spectrum regulations for the 2.4-GHz unlicensed frequency range. Regulatory approval is required for each country throughout the world where the end-user wishes to operate the Intel Personal Wireless Module(Ambler) and communicate to other Bluetooth devices.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R “This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R • Canada • Belgium • Denmark • Germany • Italy • Netherlands • Spain • Sweden • United Kingdom • • This list will be updated in future revisions bases on the grants that Intel will obtain. Note: Japan has no form of modular approval available at this time.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R Design Criteria for Modular Approval The Intel Personal Wireless Module(Ambler) with Bluetooth wireless technology may not be altered or modified in any way upon receipt from Intel. Additionally, no external component can be added which changes the radio frequency (RF) characteristics of the transmitted signals. This includes all components both passive and active such as RF filters, RF amplifiers, RF switches, etc.
® R 3. Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 width should not exceed 36 mils. Either symmetric or asymmetric stripline may be used. For design formulae visit: Table B http://www.polar.co.uk/ Coaxial Cable: Since coaxial cable is non-radiating, any length may be used. The impedance must be 50 +/- 2 ohms. In general, the lengths of all transmission lines should be kept at a minimum where possible. Microstrip is the most lossy, followed by stripline and then coax.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R In essence, this modular approval is granted provided that OEM’s take responsibility for insuring that any other transmitters operating with Ambler comply with any RF exposure requirements associated with their use.
® R Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 Note: Industry Canada generally follows the guidelines of the FCC for its emissions level requirements. Previous FCC data taken for the final configuration may be utilized to satisfy this requirement. However, emissions level requirements should be confirmed by referring to a current version of RSS-210. If no data of this type is available then testing to a current version of RSS 210 will be required.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R European Union Conditions Regulatory requirements for marketing in the EU are covered in the R&TTE Directive of April 8, 2000. This directive simplifies marketing by allowing self certification for “harmonized” bands by conducting testing at their own manufacturing facility or test house. In the case of Bluetooth, standards have recently become harmonized (although frequencies are not).
® R Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 has been taken this is an option. If no data is available then testing to ETSI 300-328 will be required. In addition we will strongly recommend testing to ETSI 300-826 (immunity testing) although this will not be Intel's responsibility for compliance of the end user configuration.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R US and International Type Approval (Standard Regulatory Equipment Certification) Some cases may arise where the OEM wishes to obtain standard equipment regulatory certification. Examples are implementations with a unique antenna or antenna connection scheme or countries where modular approval has not been approved. Details of standard type equipment certification are out of the scope of this user guide.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R Overview of Bluetooth Qualification Responsible Entity The manufacturer of a Bluetooth “end-product” is ultimately responsible for qualification of the product. An OEM who uses the Intel Personal Wireless Module(Ambler) component in their endproduct must follow the steps defined in the Qualification Program Reference Document (PRD) to fulfill the qualification requirements.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R Table FGEOP Table GObject Push Table HFile Transfer Table ISynchronization 1. 2. 3. 4. Prepare a test report to include the interoperability test data. Intel will provide sample test report for reference. Fill out Bluetooth PIC/ICXs Summary template. This template will be provided by Intel and will be filled out in advance for the functionality supported by the Intel Personal Wireless Module(Ambler) Component.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.
® R Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 Appendix B: Sample Connector and Cable to the Antenna Figure 1.
® Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 R Appendix C: FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION Certification Intel Corporation 2200 Mission College Blvd.
® R Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 the Grantee does not provide an antenna with this module, it may not be sold to the end- user, but may be sold to a second manufacturer/installer. Instructions must be provided by the Grantee to the second manufacturer/installer that describe how this module must be installed into a final product in such a manner that only the authorized antenna(s) is (are) used, and it complies with the requirements of Section 15.203 (i.
® R Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 Appendix D: Grant will be added in the next document revision.
® R Intel Ambler Module With Bluetooth* Wireless Technology Design Guide, Rev. 4.1 Appendix E: Declaration of Conformity (CE Approval) Grant will be added in the next document revision. tests either need to be done at a similar approved facility or verified using test data from an approved facility.
