Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide Intel® NUC Kit NUC5i3RYH Intel® NUC Kit NUC5i5RYH User Guide 1
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment. Disconnect the computer from its power source and from any telecommunications link or network before performing any of the procedures described in this guide.
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide This guide tells you how to: • • • • • • Install and remove memory Install an M.2 SSD Install a 2.5” drive Install a VESA mount bracket Install an operating system Install the latest drivers Open the Intel NUC Chassis To open the Intel NUC chassis, follow these steps: 1. Unscrew the four corner screws on the bottom cover of the chassis and lift the cover.
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Align the small notch at the bottom edge of the SO-DIMM with the key in the socket. 4. Insert the bottom edge of the SO-DIMM into the socket. 5. When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the retaining clips snap into place. Make sure the clips are firmly in place.
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide 3. Insert the bottom edge of the M.2 card into the connector (B). 4. Secure the card to the standoff with the small silver screw (C). If you are installing a 60mm or 42mm M.2 SSD: 1. Remove the small silver screw from the metal standoff on the motherboard (A). 2. Move the standoff (B) from the 80mm position to either the 60mm or 42mm position (C). 3. Align the small notch at the bottom edge of the M.2 card with the key in the connector. 4.
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide 2. Slide the 2.5” drive into the drive bay, ensuring the SATA connectors are fully seated into the connectors of the SATA daughter card (A). 3. Secure the drive into the drive bay with the two small silver screws that were included in the box (B). 4. Set the drive bay bracket down inside the chassis (C), taking care not to pinch the SATA cables along the edge (D).
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide Close the Chassis After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by hand with a screwdriver to avoid over-tightening and possibly damaging the screws. Attach and Use the VESA Bracket (Optional) Follow these instructions to attach and use the VESA mount bracket: 1. Using the four small black screws that were included in the box, attach the VESA bracket to the back of the monitor or TV.
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide 2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC. 3. Slide the Intel NUC onto the VESA mount bracket. Install an Operating System Refer to Supported Operating Systems for a list of Intel-validated Windows* operating systems, as well as versions of Linux that have been reported as compatible by Intel NUC owners. Refer to Operating System Installation for system requirements and installation steps.
Intel NUC Kit NUC5i3RYH & NUC5i5RYH User Guide Install Intel NUC Drivers To download the latest Microsoft* Windows* drivers and BIOS updates, go to Download Center: Links: Intel® NUC Kit NUC5i3RYH Intel® NUC Kit NUC5i5RYH Drivers are available for the following features: Audio Bluetooth Chipset Consumer Infrared Graphics Intel® ME Intel® Rapid Storage Technology Intel® Ready Mode Technology LAN (wired and wireless) NFC USB 3.
