Intel® NUC 11 Pro Kit NUC11TNHi3 Intel® NUC 11 Pro Kit NUC11TNHi5 Intel® NUC 11 Pro Kit NUC11TNHv5 Intel® NUC 11 Pro Kit NUC11TNHi7 Intel® NUC 11 Pro Kit NUC11TNHv7 Intel® NUC 11 Pro Kit NUC11TNHi30L Intel® NUC 11 Pro Kit NUC11TNHi50L Intel® NUC 11 Pro Kit NUC11TNHv50L Intel® NUC 11 Pro Kit NUC11TNHi70L Intel® NUC 11 Pro Kit NUC11TNHv70L User Guide January 2021 1 NUC11TNH User Guide – January 2021
You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject matter disclosed herein. No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document. All information provided here is subject to change without notice.
Contents 1.0 Introduction ............................................................................................................................. 5 1.1 1.2 1.3 Before You Begin ........................................................................................................................................... 5 Installation Precautions .............................................................................................................................
Revision History Date January 2021 Revision 1.0 Description Initial release.
1.0 Introduction This User Guide provides step-by-step installation instructions for these products: • • • • • • • • • • 1.
strap and attaching it to a metal part of the computer chassis. 1.2 Installation Precautions When you install and test the Intel NUC, observe all warnings and cautions in the installation instructions.
2.0 Open the Chassis Unscrew the four corner screws on the bottom of the chassis and lift the cover.
3.0 Install and Remove System Memory Intel NUC 11 Pro Kit NUC11TNH have two 260-pin DDR4 SO-DIMM memory slots Memory requirements: • • • 1.2V low voltage memory 2133/2400/3200 MHz SO-DIMMs Non-ECC Find compatible system memory modules at the Intel® Product Compatibility Tool: • • • • • • • • • • 3.
4. Insert the bottom edge of the SO-DIMM into the socket. 5. When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 3.2 Remove SO-DIMMs To remove a SO-DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" in Section 1.1. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. 3. Remove the AC power cord from the computer. 4. Remove the computer’s cover. 5.
4.0 Install an M.2 SSD Intel® NUC 11 Pro Kit NUC11TN support 80mm and 42mm SSDs. Find compatible M.
2. Move the standoff (B) from the 80mm position to the 42mm position (C). 3. Align the small notch at the bottom edge of the M.2 card with the key in the connector. 4. Insert the bottom edge of the M.2 card into the connector (D). 5. Secure the card to the standoff with the small silver screw (E).
5.0 Install a 2.5-inch SSD or Hard Drive Intel® NUC 11 Pro Kit NUC11TN support an additional 2.5” Solid State Drive (SSD) or Hard Disk Drive (HDD). Find compatible M.
2. Secure the drive into the drive bay with the two small silver screws that were included in the box (B). Set the drive bay bracket down inside the chassis (C).
6.0 Close the Chassis After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by hand with a screwdriver to avoid over-tightening and possibly damaging the screws.
7.0 Use the VESA Bracket (Optional) Follow these instructions to attach and use the VESA mount bracket: 1. Using the four small black screws that were included in the box, attach the VESA bracket to the back of the monitor or TV. 2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.
3. Slide the Intel NUC onto the VESA mount bracket.
8.0 Connect Power Each Intel NUC model includes either a region-specific AC power cord or no AC power cord (only the power adapter). Product codes Power cord type BNUC11TNHI70000 No power cord included. An AC power cord needs to be purchased separately. Power cords are available at many Internet sites for use in multiple countries. The connector on the power adapter is a C5 type connector. BNUC11TNHI70001 US power cord included. BNUC11TNHI70002 EU power cord included.
9.0 Install an Operating System See Supported Operating Systems for a list of Intel-validated Windows* operating systems. The Intel Product Compatibility Tool lists versions of Linux* that have been reported as compatible by Intel NUC owners. If you need assistance with Linux on your Intel NUC, check the distribution’s website and forums for peer assistance. Refer to Operating System Installation for system requirements and installation steps.
10.
