IB957 Intel ® ArrandaleTM /PCH 5.25” Motherboard USER’S MANUAL Version 1.
Acknowledgments AMI is a registered trademark of American Megatrends Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Intel® Arrandale DC Mobile Processor are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Fintek is a registered trademark of Fintek Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction ....................................................... 1 Product Description ............................................................. 1 Checklist .............................................................................. 2 IB957 Specifications ........................................................... 3 Board Dimensions ............................................................... 4 Installations .......................................................
IMPORTANT NOTE: When the system boots without the CRT being connected, there will be no image on screen when you insert the CRT/VGA cable. To show the image on screen, the hotkey must be pressed (CTRL-ALT-F1).
INTRODUCTION Introduction Product Description The IB957 5.25” Disk-Size SBC is a high performance Intel® Core™ i7-610E (2.53GHz/4MB) Processor-based IB957 5.25” Disk-Size SBC with the mobile Intel® QM57 Express Chipset. It is designed for a range of automation, industrial, and medical applications. The Intel® Core™ i7 Mobile processor has an optimized integrated graphics solution. IB957 features a low-power design that is validated with Intel® Core™ i7/i3 Mobile processors on 32nm process.
INTRODUCTION Checklist Your IB957 package should include the items listed below.
INTRODUCTION IB957 Specifications CPU Supported CPU Voltage System Speed CPU FSB Cache Green /APM CPU Tpye Chipset BIOS Memory VGA LVDS LCD Panel LAN USB Serial ATA Ports IAMT6.0 Audio LPC I/O Digital IO Keyboard/Mouse Expansion Slots Edge Connector Onboard Header/ Connector Watchdog Timer System Voltage Others Board Size Intel® Arrandale+ECC processor - i7-610E (2.53GHz/4M Cache/ 2 cores/4 Threads/35W) - i3-330E (2.13GHz/3M Cache/ 2 cores/4 Threads/35W) 0.700V ~ 1.5V (IMVP-6.5) Up to 3.
INTRODUCTION [ Board Dimensions 4 IB957 User’s Manual
INTRODUCTION IB957 User’s Manual 5
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB957 in order to set up a workable system. The topics covered are: Installing the Memory ............................................................................ 7 Setting the Jumpers ................................................................................ 8 Connectors on IB957 ...........................................................................
INSTALLATIONS Installing the Memory The IB957 board supports two DDR3 memory socket for a maximum total memory of 8GB in DDR3 w/ECC DIMM memory type. Installing and Removing Memory Modules To install the DDR3 modules, locate the memory slot on the board and perform the following steps: 1. Hold the DDR3 module so that the key of the DDR3 module aligned with that on the memory slot. 2.
INSTALLATIONS Setting the Jumpers Jumpers are used on IB957 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB957 and their respective functions. Jumper Locations on IB957 ................................................................... 9 JP2: LCD Panel Power Selection.........................................................
INSTALLATIONS Jumper Locations on IB957 Jumpers on IB957 ............................................................................. Page JP2: LCD Panel Power Selection ........................................................ 10 JP3, JP4, JP5: RS232/422/485 (COM2) Selection .............................. 10 JBAT1: Clear CMOS Setting ..............................................................
INSTALLATIONS JP2: LCD Panel Power Selection JP2 LCD Panel Power 3.3V 5V JP3, JP4, JP5: RS232/422/485 (COM2) Selection COM1 is fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485. The following table describes the jumper settings for COM2 selection.
INSTALLATIONS COM2 is jumper selectable for RS-232, RS-422 and RS-485.
INSTALLATIONS Connectors on IB957 Connector Locations on IB957 ............................................................ 13 CN1: DC Adapter Connector ............................................................... 14 CN2: DVI-D and VGA Connector ...................................................... 14 HDMI1: HDMI Connector .................................................................. 15 CN3: USB11/12 Ports..........................................................................
INSTALLATIONS Connector Locations on IB957 IB957 User’s Manual 13
INSTALLATIONS CN1: DC Adapter Connector CN1 provides DC12V that provide system power +5,+3.3,+12V,5VSB CN2: DVI-D and VGA Connector [ 14 Signal Name Pin # Pin # Signal Name DATA 2DATA 2+ Shield 2/4 DATA 4DATA 4+ DDC CLOCK DDC DATA N.C DATA 1DATA 1+ SHIELD 1/3 DATA 3DATA 3+ DDC POWER A GROUND 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 C6 HOT PLUG DATA 0DATA 0+ SHIELD 0/5 DATA 5DATA 5+ SHIELD CLK CLOCK CLOCK + N.C. N.C. N.C. N.C. N.C. N.C.
INSTALLATIONS HDMI1: HDMI Connector Signal Name Pin # Pin # Signal Name DATA 2DATA 2+ Shield 2/4 DATA 4DATA 4+ DDC CLOCK DDC DATA N.
INSTALLATIONS COM3_COM4: COM3, COM4 Serial Port Signal Name DSR RTS CTS RI NA DSR RTS CTS RI NA Pin # 2 4 6 8 10 12 14 16 18 20 Pin # 1 3 5 7 9 11 13 15 17 19 Signal Name DCD RXD TXD DTR Ground DCD RXD TXD DTR Ground SYS_FAN1: System Fan Power Connector This is a 3-pin header for system fans. The fan must be a 12V (500mA). Pin # 1 2 3 Signal Name Ground +12V Rotation detection CPU_FAN1: CPU Fan Power Connector This is a 3-pin header for the CPU fan. The fan must be a 12V fan.
INSTALLATIONS J1 (F_PANEL): System Function Connector J1 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. J2 is a 20-pin header that provides interfaces for the following functions. Hard Disk Drive LED Reset Switch Not Defined ATX Power On Switch Not Defined Power LED Speaker Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended.
INSTALLATIONS ATX Power ON Switch: Pins 7 and 17 This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off. Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header.
INSTALLATIONS J3: LCD Backlight Connector Pin # Signal Name 1 +12V 2 Backlight Enable 3 Brightness Control 4 Ground J4, J5: +12V and +5V Output Power Connectors J6: Printer Port Connectors J7: SPI Flash Connector (factory use only) J8: CD-In Pin Header Pin # Signal Name 1 CD Audio R 2 Ground 3 Ground 4 CD Audio L J9: PS/2 Keyboard/Mouse Connector Signal Name Ground Vcc MSDATA MSCLK Pin 1 3 5 7 Pin 2 4 6 8 Signal Name Ground Vcc KBDATA KBCLK NC 9 10 NC IB957 User’s Manual 19
INSTALLATIONS J10: Digital I/O Signal Name GND OUT3 OUT2 IN3 IN2 Pin 1 3 5 7 9 J11: Front Audio Connector Signal Name Pin # MIC2_L 1 MIC2_R 3 Line2_L 5 Sense 7 Line2_R 9 Pin 2 4 6 8 10 Signal Name VCC OUT1 OUT0 IN1 IN0 Pin # 2 4 6 8 10 Signal Name Ground Presence# MIC2_ID NC Line2_ID J12: PCI-E(x1) Slot J13: SPDIF Out Connector JMINI: Mini PCIE Connector SATA1, SATA2, SATA3, SATA4: SATA Connectors 20 IB957 User’s Manual
INSTALLATIONS F_USB1: USB1/USB5 Connector Signal Name Vcc D0D0+ Ground Pin 1 3 5 7 Pin 2 4 6 8 Signal Name Vcc D1D1+ Ground NC 9 10 Ground Signal Name Vcc D0D0+ Ground Pin 1 3 5 7 Pin 2 4 6 8 Signal Name Vcc D1D1+ Ground NC 9 10 Ground F_USB2: USB0/USB3 Connector COM1,COM2: COM1,COM2 Serial Port COM2 Signal Name DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground Pin # 1 2 3 4 5 Pin # 6 7 8 9 10 IB957 User’s Manual Signal Name DSR, Data
INSTALLATIONS LVDS1, LVDS2: LVDS Connectors (1st channel, 2nd channel) The LVDS connectors on board consist of the first channel (LVDS1) and second channel (LVDS2). Signal Name TX0Ground TX15V/3.3V TX3TX2Ground TXC5V/3.
BIOS SETUP BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction ........................................................................................ 24 BIOS Setup .................................................................................................... 24 Main BIOS Setup .........................................................................................
BIOS SETUP BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. BIOS Setup The BIOS provides a Setup utility program for specifying the system configurations and settings.
BIOS SETUP Main BIOS Setup This setup allows you to record some basic hardware configurations in your computer system and set the system clock.
BIOS SETUP Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP PCI Subsystem Settings This section allows you to configure the PCI, PCI-X and PCI Express settings. Aptio Setup Utility Main Advanced Chipset Boot Security PCI Bus Driver Version PCI ROM Priority V 2.02.
BIOS SETUP PCI Express Link Settings Set Maximum Read Request Size of PCI Express Device or allow System BIOS to select the value.
BIOS SETUP ACPI Settings Aptio Setup Utility Main Advanced Chipset Boot Security Enable ACPI Auto Configuration Disabled ACPI Sleep State S3 (Suspend to R…) Save & Exit Event Logs → ← Select Screen ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Enabled ACPI Auto Configuration Enables or Disables BIOS ACPI Auto Configuration.
BIOS SETUP Wake up event settings Aptio Setup Utility Main Advanced Chipset Boot Wake system with Fixed Time Wake up hour Wake up minute Wake up second Disabled 0 0 0 Wake on Ring Wake on PCI PME Wake on PCIE Wake Event Disabled Disabled Disabled Security Save & Exit Event Logs → ← Select Screen ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Wake system with Fixed Time Enables or Disables System wake on alarm event.
BIOS SETUP CPU Configuration This section shows the CPU configuration parameters.
BIOS SETUP Adjacent Cache Line Prefetch To turn on/off prefetching of adjacent cache lines. Intel Virtualization Technology When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Power Technology Enable the power management features. SATA Configuration SATA Devices Configuration.
BIOS SETUP Intel IGD SWSCI OpRegion Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen Intel IGD SWSCI OpRegion Configuration DVMT/FIXED Memory IGD – Boot Type Active LVDS LVDS Channel Type LVDS Panel Color Depth LVDS LCD Panel Type 256MB VBIOS Default No LVDS Auto 18bit 1024x768 LVDS ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit DVMT/FIXED Memory Select DVMT/FIXED Mode Mem
BIOS SETUP Intel TDT(AT-p) Configurations Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen Intel Theft Deterrence Technology Configuration TDT TDT Recovery Disabled 3 ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit TDT Enable/Disable TDT in BIOS for testing only. TDT Recovery Set the number of times Recovery attempted will be allowed.
BIOS SETUP USB Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen USB Configuration USB Devices: 2 Hubs Legacy USB Support EHCI Hand-off Device Reset Timeout Enabled Enabled 20 sec ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Legacy USB Support Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected.
BIOS SETUP Super IO Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen Super IO Configuration Super IO Chip -> Serial Port 0 Configuration -> Serial Port 1 Configuration -> Serial Port 2 Configuration -> Serial Port 3 Configuration Parallel Port Configuration Power Failure ACPI Shutdown Temperature Fintek F81865 Always off Disable ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4
BIOS SETUP H/W Monitor Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen PC Health Status CPU Temperature System Temperature CPU FAN Speed VCC3V Vcore 5V 12V 1.5V VSB3V VBAT CPU Fan Smart Fan Control +51 C +35 C 7109 RPM +3.408 V +0.928 V +5.087 V +11.880V +1.552 V +3.392 +3.
BIOS SETUP Thermal Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen Thermal Configuration Intelligent Power Sharing ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Intelligent Power Sharing • Intelligent power sharing – The default setting is Enabled. • Mch Turbo – The default setting is Enabled. • IPS Policy – The default setting is Driver.
BIOS SETUP AMT Configuration Aptio Setup Utility Main Advanced Chipset AMT Unconfigure AMT/ME Boot Security Save & Exit Event Logs → ← Select Screen Enabled Disabled ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit AMT Options are Enabled and Disabled. Unconfigure AMT/ME Perform AMT/ME unconfigure without password operation.
BIOS SETUP Chipset Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Aptio Setup Utility Main Advanced Enable CSID ► North Bridge ► South Bridge ► ME Subsystem Chipset Boot Security Save & Exit Event Logs → ← Select Screen Disabled ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Enable CSID By default, this item is disabled.
BIOS SETUP North Bridge This section allows you to configure the North Bridge Chipset.
BIOS SETUP PCI Express Port Options are Disabled, Enabled and Auto. IGD Memory IGD Share Memory Size. Options are Disable, 32M, 64M and 128M. PAVP Mode Select PAVP Mode used by Internal Graphics Device. Options are Disabled and Enabled. PEG Force Gen1 PCI Express Port Force Gen1.
BIOS SETUP SB Chipset Configuration This section allows you to configure the South Bridge Chipset.
BIOS SETUP PCI Express Ports Configuration Enable or Disable the PCI Express Ports in the Chipset.
BIOS SETUP Intel ME Subsystem This section allows you to configure the PCI settings. Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Event Logs → ← Select Screen Intel ME Subsystem Configuration ME Version 6.0.3.
BIOS SETUP Boot Settings This section allows you to configure the boot settings according to your preference. Aptio Setup Utility Main Advanced Chipset Boot Boot Configuration Quiet Boot Fast Boot Setup Prompt Timeout Bootup NumLock State CSM16 Module Version GateA20 Active Option ROM Messages Interrupt 19 Canture Boot Option Priorities Boot Option #1 Security Save & Exit Disabled Disabled 1 On 07.
BIOS SETUP Boot Option Priorities Sets the system boot order. Hard Drive BBS Priorities Set the order of the legacy devices in this group. Security Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP Save & Exit Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Save Changes and Exit Disacard Changes and Exit Save Changes and Reset Discard Changes and Reset → ← Select Screen ↑↓ Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override SATA: ATAPI iHDS116 4 SATA: Hitachi HDS721616P
BIOS SETUP Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. Boot Override Pressing ENTER causes the system to enter the OS. Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. Reset System with ME disable Mode ME will run into the temporary disable mode.
BIOS SETUP Event Logs This section allows you to configure the Smbios Event Log. according to your preference.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under Windows operating systems. The software and drivers are included with the motherboard. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel Chipset Software Installation Utility ........................................... 52 VGA Drivers Installation ..............................................
DRIVER INSTALLATION Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility. 3.
DRIVERS INSTALLATION 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On the Readme File Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect.
DRIVER INSTALLATION VGA Drivers Installation NOTE: Before installing the Intel(R) QM57 Chipset Family Graphics Driver, the Microsoft .NET Framework 3.5 SPI should be first installed. To install the VGA drivers, follow the steps below. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Intel(R) QM57 Chipset Family Graphics Driver. 3. When the Welcome screen appears, click Next to continue.
DRIVERS INSTALLATION 4. Click Yes to to agree with the license agreement and continue the installation. 5. On the Readme File Information screen, click Next to continue the installation of the Intel® Graphics Media Accelerator Driver. 6. On Setup Progress screen, click Next to continue. 7. Setup complete. Click Finish to restart the computer and for changes to take effect.
DRIVER INSTALLATION Realtek HD Audio Driver Installation Follow the steps below to install the Realtek HD Audio Drivers. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Realtek High Definition Audio Driver. 3. On the Welcome to the InstallShield Wizard screen, click Next. 3. InstallShield Wizard is complete. Click Finish to restart the computer.
DRIVERS INSTALLATION LAN Drivers Installation Follow the steps below to install the Intel LAN drivers. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) QM57 Chipset Drivers. 2. Click Intel(R) PRO LAN Network Driver. 3. When the Welcome screen appears, click Next. On the next screen, click Yes to to agree with the license agreement.
DRIVER INSTALLATION 4. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue. 5. The wizard is ready to begin installation. Click Install to begin the installation.
DRIVERS INSTALLATION 6. When InstallShield Wizard is complete, click Finish.
DRIVER INSTALLATION Intel® Management Engine Interface NOTE: Before installing the Intel(R) AMT 6.0 Drivers, the Microsoft .NET Framework 3.5 SPI should be first installed. Follow the steps below to install the Intel Management Engine. 1. Insert the drivers disc that comes with the motherboard. Click Intel and then Intel(R) AMT 6.0 Drivers.
DRIVERS INSTALLATION 2. When the Welcome screen to the InstallShield Wizard for Intel® Management Engine Components, click Next. On the next screen, click Yes to to agree with the license agreement. 2. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed.
DRIVER INSTALLATION 62 IB957 User’s Manual
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.
APPENDIX C. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
APPENDIX return 0; } //--------------------------------------------------------------------------void EnableWDT(int interval) { unsigned char bBuf; bBuf = Get_F81865_Reg(0x2B); bBuf &= (~0x20); Set_F81865_Reg(0x2B, bBuf); //Enable WDTO Set_F81865_LD(0x07); Set_F81865_Reg(0x30, 0x01); //switch to logic device 7 //enable timer bBuf = Get_F81865_Reg(0xF5); bBuf &= (~0x0F); bBuf |= 0x52; Set_F81865_Reg(0xF5, bBuf); //count mode is second Set_F81865_Reg(0xF6, interval); //set timer bBuf = Get_F81865_Reg(
APPENDIX //--------------------------------------------------------------------------// // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //--------------------------------------------------------------------------#include "F81865.H" #include
APPENDIX unsigned char Get_F81865_Reg(unsigned char REG) { unsigned char Result; Unlock_F81865(); outportb(F81865_INDEX_PORT, REG); Result = inportb(F81865_DATA_PORT); Lock_F81865(); return Result; } //--------------------------------------------------------------------------- //--------------------------------------------------------------------------// // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED
