AR-B1760 Socket 479 Pentium® M Intel® 855GME 5.25” SBC USER’S MANUAL Version 1.
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction .......................................................1 Product Description............................................................. 1 Checklist.............................................................................. 2 AR-B1760 Specifications.................................................... 3 Board Dimensions ............................................................... 4 Installations .......................................................
This page is intentionally left blank.
INSTALLATIONS Introduction Product Description The AR-B1760 Pentium® M 5.25” embedded board incorporates the Intel® advanced 855GME Chipset that supports processors from 600MHz to 2.0MHz in both 478 or 479-ball Micro-FCBGA package with a front size bus of 400MHz. Graphics display functionality is provided by the integrated-chipset VGA controller that supports CRT display and LVDS interface with 24-bit panel specifications.
INSTALLATIONS Checklist Your AR-B1760 package should include the items listed below.
INSTALLATIONS AR-B1760 Specifications Form Factor CPU Type CPU Voltage System Speed CPU Frequency Green /APM Chipset BIOS Cache VGA DVI Port (option) LAN Audio Memory type LPC I/O Secondary I/O RTC/CMOS Battery KB Controller IDE Compact Flash Serial ATA (option) Digital I/O USB Watchdog Timer Power Connector System Voltages Expansion Slots 5.25-inch Disk-Size Intel Pentium® M Processor, Ultra Low Voltage, at HFM core frequency of 600 MHz ~ 2.0GHz, 478 or 479-ball Micro-FCBGA Package 0.700V~1.
INSTALLATIONS Board Dimensions 4 AR-B1760 User’s Manual
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the AR-B1760 in order to set up a workable system. The topics covered are: Installing the CPU ............................................................... 6 Installing the Memory ......................................................... 7 Setting the Jumpers ............................................................. 8 Connectors on AR-B1760 .................................................
INSTALLATIONS Installing the CPU The AR-B1760 embedded board supports a Socket 479 processor socket for Intel® Pentium® M or Celeron® M processors. The processor socket comes with a screw to secure the processor. As shown in the left picture below, loosen the screw first before inserting the processor. Place the processor into the socket by making sure the notch on the corner of the CPU corresponds with the notch on the inside of the socket. Once the processor has slide into the socket, fasten the screw.
INSTALLATIONS Installing the Memory The AR-B1760 embedded board supports two DDR memory sockets for a maximum total memory of 2GB in DDR memory type. The memory module capacities supported are 64MB, 128MB, 256MB, 512MB and 1GB. The following table lists the supported DDR DIMM configurations. Intel 855GME supports configurations defined in the JEDEC DDR DIMM specification only (A,B,C). Non-JEDEC standard DIMMs such as double-sided x16 DDR SDRAM DIMMs are not supported. Supported DDRM DIMM Configurations.
INSTALLATIONS Setting the Jumpers Jumpers are used on AR-B1760 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on AR-B1760 and their respective functions. Jumper Locations on AR-B1760 .................................................... 9 Configuring the CPU Frequency .................................................. 10 JP1: LVDS Panel Power Select ....
INSTALLATIONS Jumper Locations on AR-B1760 Jumpers on AR-B1760 ..............................................................Page Configuring the CPU Frequency .................................................. 10 JP1: LVDS Panel Power Select.................................................... 10 JP2: Gigabit LAN Enable/Disable................................................ 10 JP3: Compact Flash Slave/Master ................................................ 10 JP4: Clear CMOS Contents ....................
INSTALLATIONS Configuring the CPU Frequency The AR-B1760 embedded board does not provide DIP switches to configure the processor speed (CPU frequency). JP1: LVDS Panel Power Select JP1 LVDS Panel Power 3.3V (default) 5V Note: The LVDS panel resolution can be configured in the BIOS Setup.
INSTALLATIONS JP4: Clear CMOS Contents Use JP4 to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the board before clearing CMOS. JP4 Setting Function Pin 1-2 Short/Closed Normal Pin 2-3 Short/Closed Clear CMOS JP5, JP6, JP7: RS232/422/485 (COM2) Selection COM1, COM3, and COM4 are fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485. The following table describes the jumper settings for COM2 selection.
INSTALLATIONS JP9: COM2 RS232 +5V / +12V Power Setting Pin # Signal Name Signal Name Pin # 1 RI +12V 2 3 RI (default) RI (default) 4 5 RI +5V 6 JP9 COM2 Settings: Pin 1-2 short = +12V, Pin 5-6 short = +5V, Pin 3-4 short = standard COM port JP10: COM3 RS232 +5V / +12V Power Setting Pin # Signal Name Signal Name Pin # 1 RI +12V 2 3 RI (default) RI (default) 4 5 RI +5V 6 JP10 COM3 Settings: Pin 1-2 short = +12V, Pin 5-6 short = +5V, Pin 3-4 short = standard COM port JP11: COM
INSTALLATIONS JP16: Processor Operating Frequency JP16 CPU FSB 133MHz Open 100MHz Close AR-B1760 User’s Manual 13
INSTALLATIONS Connectors on AR-B1760 The connectors on AR-B1760 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on AR-B1760 and their respective functions. Connector Locations on AR-B1760 ............................................. 15 FAN1, FAN2: System Fan Power Connector............................... 16 FAN3: CPU Fan Power Connector...............................................
INSTALLATIONS Connector Locations on AR-B1760 Connectors on AR-B1760.....................................................................Page Connector Locations on AR-B1760.......................................................................... 15 FAN1, FAN2: System Fan Power Connector........................................................... 16 FAN3: CPU Fan Power Connector........................................................................... 16 IDE1, IDE2: EIDE Connectors ......................
INSTALLATIONS FAN1, FAN2: System Fan Power Connector FAN1, FAN2 is a 3-pin header for system fans. The fan must be a 12V (500mA) fan. Pin # 1 2 3 Signal Name Ground +12V Rotation detection FAN3: CPU Fan Power Connector FAN3 is a 3-pin header for the CPU fan. The fan must be a 12V fan.
INSTALLATIONS IDE2: Secondary IDE Connector Signal Name Pin # Pin # Signal Name Reset IDE Host data 7 Host data 6 Host data 5 Host data 4 Host data 3 Host data 2 Host data 1 Host data 0 Ground DRQ0 Host IOW Host IOR IOCHRDY DACK0 IRQ14 Address 1 Address 0 Chip select 0 Activity Vcc Ground 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Ground Host data 8 Host data 9 Host data 10 Host data 11 Host data 12 Host data 13 Host data 14
INSTALLATIONS J2: External Audio Connector Signal Name LINEOUT_R Ground LINEIN_R Ground Mic-In Ground Pin # 1 3 5 7 9 11 Pin # 2 4 6 8 10 12 Signal Name LINEOUT_L Ground LINEIN L Ground VREFOUT Protect pin CN3: Digital 4-in 4-out I/O Connector Signal Name Ground Out3 Out2 Int3 Int2 Pin 1 3 5 7 9 Pin 2 4 6 8 10 Signal Name Vcc Out1 Out0 Int1 Int0 J3: Wake On LAN Connector J3 is a 3-pin header for the Wake On LAN function on the CPU card.
INSTALLATIONS J4: Gigabit LAN Connector (used with ID240/option) Signal Name MDI0+ 2.5V MDI1+ MDI2+ 2.5V MDI3+ ACT_LED Link1000_LED Pin 1 2 3 4 5 6 7 8 Pin 9 10 11 12 13 14 15 16 Signal Name MDI0GND MDI1MDI22.5V MDI3LINK_UP Link100_LED J5: System Function Connector J5 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. J5 is a 16-pin header that provides interfaces for the following functions.
INSTALLATIONS ATX Power ON Switch: Pins 5 and 13 This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off.
INSTALLATIONS J6: TMDS Connector (option) Signal Name TX1P TX1N GND GND TXCP TXCN GND VCC+5V HPDET NC Pin # 1 2 3 4 5 6 7 8 9 10 Pin # 11 12 13 14 15 16 17 18 19 20 Signal Name TX2P TX2N GND GND TXOP TXON NC NC DDCDATA DDCCLK J7: 10/100Mbit Ethernet Connector Signal Name 5VSB RX+ LILED ACTLED TX+ Pin 1 2 3 4 5 Pin 6 7 8 9 10 Signal Name SPEED LED RXPULL LOW PULL LOW TX- Pin 1 2 3 4 5 6 7 8 Pin 9 10 11 12 13 14 15 16 Signal Name +5V GND NC DDCDAT HSYNC VSYNC DDCCLK Protect pin J8: VGA CRT Connect
INSTALLATIONS J10: Floppy Drive Connector J10 is a slim 26-pin connector and will support up to 2.88MB FDD.
INSTALLATIONS J14: Panel Inverter Power Connector Pin # 1 2 3 Signal Name +12V ENABKL Ground J15, J16: USB Connectors The following table shows the pin outs of the USB pin headers connectors. Overall, the two pin headers support four USB ports (USB 2.0 compliant).
INSTALLATIONS J18: Serial Ports Pin # Signal Name (RS-232) 1 2 3 4 5 6 7 8 9 10 DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready Ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator No Connect. COM2 is jumper selectable for RS-232, RS-422 and RS-485.
INSTALLATIONS J21: ATX Power Supply Connector 11 1 20 10 Signal Name 3.3V -12V Ground PS-ON Ground Ground Ground -5V +5V +5V Pin # 11 12 13 14 15 16 17 18 19 20 Pin # 1 2 3 4 5 6 7 8 9 10 Signal Name 3.3V 3.3V Ground +5V Ground +5V Ground Power good 5VSB +12V J23: PS/2 Keyboard/Mouse Connector J23, a 10-pin header connector, has functions for both keyboard and mouse. The following table shows the pin assignments of this connector. Signal Name Pin # Pin # Signal Name Protect pin 10 5 N.C.
INSTALLATIONS Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sort of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
INSTALLATIONS Enable_And_Set_Watchdog Endp ;[]=============================================== ; Name : Disable_Watchdog ; IN : None ; OUT : None ;[]=============================================== Disable_Watchdog Proc Near call Unlock_Chip mov cl, 07h mov al, 08h call Write_Reg ;switch to LD8 xor al, al mov cl, 0F6h call Write_Reg ;clear watchdog timer xor al, al mov cl, 30h call Write_Reg ;watchdog disabled call Lock_Chip ret Disable_Watchdog Endp ;[]=============================================== ;
INSTALLATIONS ; OUT : None ;[]================================================ Write_Reg Proc Near push ax mov dx, 4Eh mov al,cl out dx,al pop ax inc dx out dx,al ret Write_Reg Endp ;[]================================================ ; Name : Read_Reg ; IN : CL - register index ; OUT : AL - Value to read ;[]=================================================== Read_Reg Proc Near Mov al, cl mov dx, 4Eh out dx, al inc dx in al, dx ret Read_Reg Endp ;[]================================================ 28 AR-B1
INSTALLATIONS Digital I/O Sample Code Filename: W627hf.h //===================================================================== // // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
INSTALLATIONS Filename: W627hf.cpp //===================================================================== // // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //===================================================================== #include "W627HF.H" #include
INSTALLATIONS File of the Main.cpp //===================================================================== // // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //===================================================================== #include #include #include #include #include "W627HF.
INSTALLATIONS This page is intentionally left blank.
BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction ........................................................................ 34 BIOS Setup................................................................................... 34 Standard CMOS Setup ................................................................. 36 Advanced BIOS Features ..................................
BIOS SETUP BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium 4 processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ESC : Quit F10 : Save & Exit Setup Ç È Æ Å : Select Item Time, Date, Hard Disk Type… The section below the setup items of the Main Menu display
BIOS SETUP Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
BIOS SETUP Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the / or +/- keys to set the current time. IDE Primary HDDs / IDE Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. Each channel can support up to two hard disks; the first is the “Master” and the second is the “Slave”.
BIOS SETUP Video This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt On This field determines whether or not the system will halt if an error is detected during power up. No errors The system boot will not be halted for any error that may be detected.
BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items. First/Second/Third Boot Device These fields determine the drive that the system searches first for an operating system. The options available include Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, ZIP100, USB-FDD, USB-CDROM, USB-HDD and Disable.
BIOS SETUP Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. Security Option This field allows you to limit access to the System and Setup. The default value is Setup. When you select System, the system prompts for the User Password every time you boot up.
BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset.
BIOS SETUP DRAM RAS# Precharge This option sets the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes. The default setting for the Active to Precharge Delay is 3. DRAM Data Integrity Mode Select ECC if your memory module supports it. The memory controller will detect and correct single-bit soft memory errors. The memory controller will also be able to detect double-bit errors though it will not be able to correct them.
BIOS SETUP AGP Aperture Size The field sets aperture size of the graphics. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation. The default setting is 64M. On-Chip VGA The default setting is Enabled. On-Chip Frame Buffer Size The default setting is 32MB. The options available include 1MB, 4MB, 8MB and 16MB. Boot Display The default setting is CRT+LVDS.
BIOS SETUP Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main items for user to select. Once an item selected, a submenu appears. Details follow.
BIOS SETUP SecondIO Device Onboard Serial Port 3 Serial Port 3 Use IRQ Onboard Serial Port 4 Serial Port 4 Use IRQ 3E8 IRQ10 2E8 IRQ11 ITEM HELP Menu Level > OnChip Primary/Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. IDE Primary/Secondary Master/Slave PIO These fields allow your system hard disk controller to work faster.
BIOS SETUP USB Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. USB 2.0 Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. In order to use USB 2.0, necessary OS drivers must be installed first. Please update your system to Windows 2000 SP4 or Windows XP SP1. USB Keyboard Support The options for this field are Enabled and Disabled. By default, this field is set to Disabled.
BIOS SETUP UART Mode Select This field determines the UART 2 mode in your computer. The default value is Normal. Other options include IrDA and ASKIR. Parallel Port Mode This field allows you to determine parallel port mode function. SPP Standard Printer Port EPP Enhanced Parallel Port ECP Extended Capabilities Port PWRON After PWR-Fail This field sets the system power status whether on or off when power returns from a power failure situation.
BIOS SETUP Power Management Setup The Power Management Setup allows you to save energy of your system effectively.
BIOS SETUP Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows BIOS to control the video display. Blank Screen Writes blanks to the video buffer. Video Off In Suspend When enabled, the video is off in suspend mode. The default setting is Yes. Suspend Type The default setting for the Suspend Type field is Stop Grant.
BIOS SETUP Power On by Ring This field enables or disables the power on of the system through the modem connected to the serial port or LAN. Resume by Alarm This field enables or disables the resumption of the system operation. When enabled, the user is allowed to set the Date and Time. Reload Global Timer Events The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events that can prevent the system from entering a power saving mode or can awaken the system from such a mode.
BIOS SETUP PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. Phoenix - AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature System Temp. CPU Temp CPU FAN Speed (FAN3) System FAN Speed (FAN1) System FAN Speed (FAN2) Vcore(V) VGMCH(V) +3.3V +5V +12V VBAT 5VSB(V) Shutdown Temperature CPU Fan Failure Warning Sys. Fan Failure Warning Aux.
BIOS SETUP Frequency/Voltage Control This section shows the user how to configure the processor frequency. Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI Clk Disabled Spread Spectrum Modulated Disabled ITEM HELP Menu Level > Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock. Spread Spectrum Modulated This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only.
BIOS SETUP Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. Load Optimized Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. Set Supervisor Password These two options set the system password.
BIOS SETUP This page is intentionally left blank.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98SE, Windows ME, Windows 2000 and Windows XP. The software and drivers are included with the motherboard. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel Chipset Software Intallation Utility .......................... 58 VGA Drivers Installation ...............................
DRIVERS INSTALLATION Intel Chipset Software Intallation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 98SE/ME/2000/XP. 1. Insert the CD that comes with the board. Click Intel Chipsets and then Intel(R) 855GME Chipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility. 3.
DRIVERS INSTALLATION 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVERS INSTALLATION VGA Drivers Installation To install the VGA drivers, follow the steps below to proceed with the installation. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) 855GME Chipset Drivers. 2. Click Intel(R) 855GME Chipset Family Graphics Driver. 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to to agree with the license agreement and continue the installation. 5.
DRIVERS INSTALLATION AC97 Codec Audio Driver Installation Follow the steps below to install the Realtek AC97 Codec Audio Drivers. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) 855GME Chipset Drivers. 2. Click Realtek AC'97 Codec Audio Driver. 3. Click Finish to restart the computer and for changes to take effect. .
DRIVERS INSTALLATION Intel PRO LAN Drivers Installation Follow the steps below to complete the installation of the Intel PRO LAN drivers. 1. Insert the CD that comes with the motherboard. Click LAN Card and then Intel(R) PRO LAN Drivers. 2. Click Install Base Software to continue. 3. When prompted, please to restart the computer for new settings to take effect.
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.