Operator's Manual
Table Of Contents
- 1. Introduction
- 1.1. Introduction
- 1.2. Safety Information
- 1.3. Device Description
- 1.4. Intended Purpose
- 1.5. BIS™ Advance Monitor System Indications and Contraindications
- 1.6. Patient Target Groups
- 1.7. Intended Users
- 1.8. Essential Performance
- 1.9. Adverse Events (Residual Risks)
- 1.10. The BIS™ Advance Parameters
- 1.11. Symbols
- 2. The BIS™ Advance Monitor — Equipment and Supplies
- 2.1. The BIS™ Advance System
- 2.2. Parts of the System
- 3. Installation and Preparation for Use
- 3.1. Operating Environment
- 3.2. Power Requirements and Battery Use
- 3.3. Battery Operation
- 3.4. Mounting the Docking Station
- 3.5. Preparing the Docking Station
- 3.6. Preparing the Monitor
- 3.7. Home Screen
- 3.8. Four-Channel Monitoring
- 3.9. Home Screen Trend Graphs
- 3.10. Home Screen Numeric Section
- 3.11. Home Screen Menus
- 3.12. Home Screen Options
- 3.13. Secondary Trend Selection
- 3.14. Home Screen Audio Alarm Settings
- 3.15. Settings and Maintenance
- 3.16. Info Options
- 3.17. Quick Reference Checklist
- 4. Operating the BIS™ Advance Monitoring System
- 4.1. Preparing for Operation
- 4.2. Cases
- 4.3. Alarms and Messages
- 4.4. Chart Data
- 4.5. Menu Map
- 4.6. Institutional Settings
- 5. Data Storage, Transfer, and Export
- 5.1. Cybersecurity and Data Integrity
- 5.2. Monitor Data Memory
- 5.3. BISx Data Memory
- 5.4. Types of Exported Data
- 5.5. Live Case Export
- 5.6. Saved Cases Export
- 5.7. Recording a Snapshot Event
- 5.8. BIS™ Saved Data Files
- 5.9. Logs Export
- 5.10. Viewing and Printing Saved Data in PDF Format
- 6. Service and Maintenance
- 6.1. Introduction
- 6.2. Servicing the BIS™ Advance Monitor
- 6.3. Battery Handling
- 6.4. Cleaning the BIS™ Advance Monitor
- 6.5. Instrument Identification
- 7. Diagnostics and Troubleshooting
- 7.1. Diagnostics
- 7.2. Troubleshooting
- 7.3. Administrator Mode
- 7.4. Demo Mode
- 7.5. Glossary
- 7.6. Specifications
- 7.6.1. General Specifications
- 7.6.2. Operating Environments
- 7.6.3. Power Supply
- 7.6.4. Battery Specifications
- 7.6.5. Controls and Connectors
- 7.6.6. Alarms
- 7.6.7. Display
- 7.6.8. Sound Pressure Data
- 7.6.9. BIS Specifications
- 7.6.10. EEG Specifications
- 7.6.11. BISx Module Specifications
- 7.6.12. Software/GUI Specifications
- 7.7. Electromagnetic Compatibility Specifications
- 7.8. Product Compliance
- 7.9. BIS™ Advance Components, Accessories, and Documentation
- 7.10. Warranty
- 7.11. Software License Agreement
Institutional Settings
BIS™ Advance Monitor
181
settings, and they shall appear as default settings to the regular (non-
Administrator) user. If the user clicks Reset to Default in any Alarm
Settings screen, the settings will return to the Institutional Default settings,
not the Factory Default settings. The institutional default settings will
remain in force even after the monitor is shut down and then restarted.
If the monitor loses power for any reason, settings that have been set for the current
sensor (including alarm settings) will remain active when the monitor is turned on
again, as long as the same sensor is attached to the monitor. If a different sensor is
attached to the monitor, the monitor will use the default settings when it is turned
on again.
Note: Note that changes can be made to the System Default settings by the
user only when a BISx module and sensor are connected to the monitor.
Exceptions to these rules are as follows:
After monitor restart, the Chart Data time interval will revert to its last value before
the monitor restarted.
After monitor restart, Live Data Recording setting (On/Off) shall revert to its last
value before the monitor restarted. When sensor is disconnected while recording
and then reconnected, the recording is not resumed automatically.
If a user applies changes to a System Default (e.g. Filters are set to Off) during a case,
the new settings will remain for the current case. At the start of the following case,
the user will be notified that these settings do not match the Institutional Defaults.
The System Default settings are not accessible when no monitoring is taking place.
To adjust Institutional settings, enter Administrator mode, and then click Main
Menu>Settings and Maintenance>Settings. Select the desired setting and
make changes as required.
Table 19. Institutional Settings
Feature Options
Factory Default
Option
Language Bulgarian, Chinese,
Croatian, Danish, Dutch,
English, French, German,
Greek, Hungarian, Italian,
Japanese, Macedonian,
English