User's Manual

Parts List
1) Reader 4.75-12.25 VDC qty 1
2) Terminal Connector 8 pins qty 1
3) Mounting cover qty 1
4) Mounting cap qty 1
5) Installation sheet qty 1
6) Mounting kit / back plate (optional) qty 1
7) Cable, 8 x 0.35 conductor as required
Installation instruction
1) Determine an appropriate position for the
Reader and drill two holes for mounting the
reader to the surface (see diagram). Do not
mount the readers less than 20 cm from each
other. Make sure that enough room to connect
the cable is allowed. Protect the cable against
sharp edges and any damage from chaffing.
2) Remove the Terminal Connector 8 pins from the
back of the Reader. Use a small flat head
screwdriver to loosen off all of the terminals.
The end of the cable should be prepared by
cutting it back to expose the wires and each end
should be twisted to eliminate any loose or
frayed wires.
3) The wires should then be connected to the
Reader inline with the Connector Assignments.
4) After wiring the reader and the Host system the
Reader is ready to be tested. Apply power and
present a Card to the Reader. The green LED
should flash and the buzzer should beep
indicating a read. If the Host system is
connected to the red and green LED inputs
these should follow the functionality of the Host
system.
5) The Reader should now be secured to the
surface using the appropriate screws. Mount the
black cover (sticker) and mount the cap over the
mounting hole.
Mullion Mounting
Connector Assignments
Wiegand / Clock and Data
SmartID/EM4102
SmartID/Hitag1&2
SmartID/DESFire
SmartID/ISO14443-3
SmartID/ISO14443-3/pin
SmartID/ISO14443/SNR
SmartID/ISO15693/SNR
1 ! Green LED input 5 ! Buzzer input
2 ! Red LED input 6 NC
3 " Data / D1 7 ! Ground
4 " Clock / D0 8 ! Power
RS232
SmartID/Hitag1&2/RW
SmartID/DESFire/RO
SmartID/ISO14443-3/Sect/RS
SmartID/ISO14443/SNR/RS
SmartID/ISO15693/SNR/RS
1 ! Green LED input 5 ! Do not connect
2 ! Red LED input 6 ! RS232 RXD
3 " Do not connect 7 ! Ground
4 " RS232 TXD 8 ! Power
RS422
SmartID/ISO14443-3/Sect
SmartID/ISO14443/SNR/RS
SmartID/ISO15693/SNR/RS
1 ! Green LED input 5 ! RS422 RXA
2 ! Red LED input 6 ! RS422 RXB
3 " RS422 TXA 7 ! Ground
4 " RS422 TXB 8 ! Power
Other FCC ID's are:
• Hitag1&2: Smart ID/Hitag1&2
PX007Z/HX " P4EHPROX-02
• ISO14443: Smart ID/ ISO14443/SNR
PX007Z/XXSNR " P4EI-MSNRPOX-02
• ISO 14443-3: Smart ID/ISO14443-3/Sect
PX007Z/MF " P4EMPROX-03
Consult your National Authority if any
authorization is needed for this product.
This device complies with Part 15 of the FCC
Rules. Operation is subject to
the following two
conditions:
1) that this device does not cause harmful
interference, and
2) that this device must accept any interference
received, including interference that may cause
undesired operation.
Integrated Engineering
Amsterdam
The Netherlands
Phone: [phone]
Fax: [phone]
Email: [e-mail]
WWW: http://www.ieprox.com