DTR-8.8_En.book Page 1 Friday, February 15, 2008 1:17 PM AV Receiver DTR-8.
DTR-8.8_En.book Page 2 Friday, February 15, 2008 1:17 PM Thank you for purchasing an Integra AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
DTR-8.8_En.book Page 3 Friday, February 15, 2008 1:17 PM Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care—Occasionally you should dust the unit all over with a soft cloth.
DTR-8.8_En.book Page 4 Friday, February 15, 2008 1:17 PM Contents Features ............................................................ 6 Supplied Accessories ...................................... 7 Multiroom Capability ........................................ 8 Getting to Know the AV Receiver ................... 9 Front Panel .............................................................. 9 Display .................................................................. 11 Rear Panel ...........................
DTR-8.8_En.book Page 5 Friday, February 15, 2008 1:17 PM Contents—Continued Advanced Setup ........................................... 101 Speaker Setup ......................................................101 Source Setup ........................................................108 Miscellaneous Setup ............................................111 Hardware Setup ...................................................113 Lock Setup ..........................................................115 Net/USB ........
DTR-8.8_En.book Page 6 Friday, February 15, 2008 1:17 PM Features Amplifier • 7-channel amplifier • 140 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
DTR-8.8_En.book Page 7 Friday, February 15, 2008 1:17 PM Features—Continued Supplied Accessories Make sure you have the following accessories: *9 XM Ready® is a trademark of XM Satellite Radio Inc. ©2005 XM Satellite Radio Inc. All rights reserved. *10 ©2005 SIRIUS Satellite Radio Inc. “SIRIUS,” SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Available only in the contiguous United States (excluding Alaska and Hawaii) and Canada.
DTR-8.8_En.book Page 8 Friday, February 15, 2008 1:17 PM Multiroom Capability You can use three speaker systems with this AV receiver—a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it, and another stereo speaker system in a third room that we call Zone 3. And, you can select a different audio source for each room. Main Room: In your main listening room, you can enjoy up to 7.
DTR-8.8_En.book Page 9 Friday, February 15, 2008 1:17 PM Getting to Know the AV Receiver Front Panel North American model 1 2 456 Q RST U V 7 8 9J K L MN O W P XY Z Other models 3 J The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item. A Standby/On button (46) Sets the AV receiver to On or Standby.
DTR-8.8_En.book Page 10 Friday, February 15, 2008 1:17 PM Getting to Know the AV Receiver—Continued E Zone 3 indicator (128) Flashes when Zone 3 is being set. Lights up when Zone 3 is on. F Remote-control sensor (15) Receives control signals from the remote controller. G Stereo button (88) Selects the Stereo listening mode. H Listening Mode [ ]/[ ] buttons (88) Select the listening modes. I Display See “Display” on page 11. J Dimmer (RT/PTY/TP) button (66, 83) Adjusts the display brightness.
DTR-8.8_En.book Page 11 Friday, February 15, 2008 1:17 PM Getting to Know the AV Receiver—Continued Display 1 234 7 8 5 9 0 A 6 B For detailed information, see the pages in parentheses. 1 Speaker/channel indicators Indicate the speaker configuration and channels used by the current input source. – : A box is displayed for each speaker that’s set in the Speaker Configuration. No box appears for speakers that are set to No or None.
DTR-8.8_En.
DTR-8.8_En.book Page 13 Friday, February 15, 2008 1:17 PM Getting to Know the AV Receiver—Continued D COMPONENT VIDEO IN 1, 2, and 3 These RCA component video inputs are for connecting components with a component video output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Input Setup” on page 51.
DTR-8.8_En.book Page 14 Friday, February 15, 2008 1:17 PM Getting to Know the AV Receiver—Continued Z CBL/SAT IN A cable or satellite receiver can be connected here. There’s S-Video and composite video input jacks for connecting the video signal. a VCR/DVR IN/OUT A video component, such as a VCR or DVR, can be connected here for recording and playback. There’s S-Video and composite video input and output jacks for connecting the video signal. b DVD IN This input is for connecting a DVD player.
DTR-8.8_En.book Page 15 Friday, February 15, 2008 1:17 PM Remote Controller Installing the Batteries 1 To open the battery compartment, press the small hollow and slide open the cover. Using the Remote Controller When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below. Remote control sensor Standby indicator AV receiver 30˚ 2 3 Insert the three supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment.
DTR-8.8_En.book Page 16 Friday, February 15, 2008 1:17 PM Remote Controller—Continued About the Remote Controller Modes As well as the AV receiver, you can also use the remote controller to control your other AV components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the Remote Mode buttons. Receiver/Tape Mode Receiver/Tape mode is used to control the AV receiver.
DTR-8.8_En.book Page 17 Friday, February 15, 2008 1:17 PM Remote Controller—Continued For detailed information, see the pages in parentheses. T L Night button (86) Turns the Late Night function on or off. A Standby button (46) Sets the AV receiver to Standby. B On button (46) U Audio Sel button (85) Selects the audio input: analog, digital, HDMI, or multichannel. Turns on the AV receiver. C Input Selector buttons (62) Used to select the input source.
DTR-8.8_En.book Page 18 Friday, February 15, 2008 1:17 PM Remote Controller—Continued A Standby button DVD Mode Sets the DVD player to Standby. To set the remote controller to DVD mode, press the [DVD] Remote Mode button. B On button Turns on the DVD player. C Number buttons Used to enter title, chapter, and track numbers, and to enter times for locating specific points. D Top Menu button Selects a DVD’s top menu.
DTR-8.8_En.book Page 19 Friday, February 15, 2008 1:17 PM Remote Controller—Continued A Standby button CD/MD/CDR Modes Sets the component to Standby. To control an Integra/Onkyo CD player, MD recorder, or CD recorder, or a CD or MD player/recorder made by another manufacturer, press the [CD] Remote Mode button to select the CD/MD/CDR remote controller mode.
DTR-8.8_En.book Page 20 Friday, February 15, 2008 1:17 PM Remote Controller—Continued A Standby button Dock Mode Turns off the iPod. Dock mode is for controlling an Apple iPod in an Onkyo RI Dock. To control an RI Dock, press the [CD] REMOTE MODE button to select the Dock remote controller mode. In order to control an RI Dock, you must first enter the appropriate remote control code (see page 132). When Using an RI Dock: • Connect the RI Dock to the TAPE IN or GAME/TV IN L/R jacks.
DTR-8.8_En.book Page 21 Friday, February 15, 2008 1:17 PM Remote Controller—Continued A Number buttons Net/USB Mode Used to enter track numbers. Net/USB mode is for playing music files on a networked computer, media server, or USB mass storage device, or for listening to Internet radio. To set the remote controller to Net/USB mode, press the [Net/USB] Remote Mode button. B Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons Used to navigate menus and select items.
DTR-8.8_En.book Page 22 Friday, February 15, 2008 1:17 PM Connecting Your Speakers Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.
DTR-8.8_En.book Page 23 Friday, February 15, 2008 1:17 PM Connecting Your Speakers—Continued Connecting a Powered Subwoofer Connecting Your Speakers Speaker Configuration For the best surround-sound experience, you should connect seven speakers and a powered subwoofer. The following table shows which channels you should use based on the number of speakers you have.
DTR-8.8_En.book Page 24 Friday, February 15, 2008 1:17 PM Connecting Your Speakers—Continued Speaker Connection Precautions Read the following before connecting your speakers: • You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more but less than 6, be sure to set the speaker impedance to 4 ohms (see page 47).
DTR-8.8_En.book Page 25 Friday, February 15, 2008 1:17 PM Connecting Your Speakers—Continued Bi-amping Speaker Hookup Bi-amping the Front Speakers The FRONT L/R and SURR BACK L/R terminal posts can be used with front speakers and surround back speakers respectively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance. • When bi-amping is used, the AV receiver is able to drive up to 5.
DTR-8.8_En.book Page 26 Friday, February 15, 2008 1:17 PM Connecting Your Speakers—Continued Bridged Speaker Hookup Bridging the Front Speakers The FRONT L/R and SURR BACK L/R terminal posts can be used with front speakers and surround back speakers respectively, or bridged together to provide almost double the output power for the front speakers. • When bridging is used, the AV receiver is able to drive 2 speakers in the main room (2.1 speakers if you’re using a powered subwoofer).
DTR-8.8_En.book Page 27 Friday, February 15, 2008 1:17 PM Connecting Antennas This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. 2 Use thumbtacks or something similar to fix the FM antenna into position. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. ■ North American Model Thumbtacks, etc.
DTR-8.8_En.book Page 28 Friday, February 15, 2008 1:17 PM Connecting Antennas—Continued ■ Using a TV/FM Antenna Splitter It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.
DTR-8.8_En.book Page 29 Friday, February 15, 2008 1:17 PM Connecting Your Components AV Connection Color Coding About AV Connections RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.
DTR-8.8_En.book Page 30 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting Audio and Video Signals to the AV Receiver By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD player, etc.
DTR-8.8_En.book Page 31 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued ■ HDMI Monitor Setting Set to No With the HDMI Monitor setting set to No (see page 48), video input signals flow through the AV receiver as shown, with composite video and S-Video sources being upconverted for the component video output. Use this setting if you connect the AV receiver’s COMPONENT VIDEO MONITOR OUT 1 or COMPONENT VIDEO MONITOR OUT 2/ZONE 2 OUT to your TV.
DTR-8.8_En.book Page 32 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a TV or Projector Step 1: Video Connection Choose a video connection that matches your TV ( A , B , or C ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3.
DTR-8.8_En.book Page 33 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a DVD player Step 1: Video Connection Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection.
DTR-8.8_En.book Page 34 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Hooking Up the Multichannel Input If your DVD player supports multichannel audio formats such as DVD-Audio and SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s MULTI CH FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.
DTR-8.8_En.book Page 35 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a VCR or DVR for Playback With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches your VCR or DVR ( A , B , or C ), and then make the connection.
DTR-8.8_En.book Page 36 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a VCR or DVR for Recording Step 1: Video Connection Choose a video connection that matches your VCR or DVR ( A or B ), and then make the connection. The video source to be recorded must be connected to the AV receiver via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your VCR or DVR ( a or b ), and then make the connection.
DTR-8.8_En.book Page 37 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a Satellite, Cable, or Terrestrial Set-top box or Other Video Source With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches the video source ( A , B , or C ), and then make the connection.
DTR-8.8_En.book Page 38 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting Components with HDMI About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
DTR-8.8_En.book Page 39 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Making HDMI Connections Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV, projector, and so on. Step 2: Assign each HDMI IN to an input selector. See “HDMI Input Setup” on page 50. ■ Video Signals Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT MAIN or HDMI OUT SUB for display on your TV.
DTR-8.8_En.book Page 40 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a Game Console Step 1: Video Connection Choose a video connection that matches your game console ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection.
DTR-8.8_En.book Page 41 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a Camcorder or Other AV Component Step 1: Video Connection Choose a video connection that matches your camcorder ( A or B ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your camcorder ( a or b ), and then make the connection.
DTR-8.8_En.book Page 42 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a CD Player Step 1: Choose a connection that matches your CD player ( a , b , or c ), and then make the connection.
DTR-8.8_En.book Page 43 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches your recorder ( a , b , c , or d ), and then make the connection.
DTR-8.8_En.book Page 44 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting an RI Dock ■ If Your iPod Supports Video: Connect your RI Dock’s audio output jacks to the AV receiver’s GAME/TV IN L/R jacks, and connect its video output jack to the AV receiver’s GAME/TV IN V jack. (Onkyo DS-A2 hookup shown below.) ■ If Your iPod Doesn’t Support Video: Connect your RI Dock’s audio output jacks to the AV receiver’s GAME/TV IN L/R jacks. (Onkyo DS-A2 hookup shown below.
DTR-8.8_En.book Page 45 Friday, February 15, 2008 1:17 PM Connecting Your Components—Continued Connecting Integra/Onkyo Components Step 1: Make sure that each Integra/Onkyo component is connected to the AV receiver with an analog audio cable (RCA). Step 2: Make the necessary connections (see illustration below). Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 52).
DTR-8.8_En.book Page 46 Friday, February 15, 2008 1:17 PM Turning On the AV Receiver • North American model • Other models Standby/On Standby indicator Standby Standby/On Standby indicator On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - TV On Input Tape CD Tuner 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 47 Friday, February 15, 2008 1:17 PM First Time Setup This section explains the settings that you need to make before using the AV receiver for the very first time. Speaker Settings Game/TV 3 AUX 1 AUX 2 TV CH If you change these settings, you-must run the automatic speaker setup again (see page 55). 4 5 6 Tape Tuner CD 7 8 9 Phono Net/USB D.TUN +10 0 Clear 11 --/--- 10 Input Selector Enter TV VOL 2-1.
DTR-8.8_En.book Page 48 Friday, February 15, 2008 1:17 PM First Time Setup—Continued HDMI Monitor Setup 2 Enter On Standby DVD VCR/DVR Use the Up and Down [ ]/[ ] buttons to select “1. Input/Output Assign,” and then press [Enter]. The Input/Output Assign menu appears. TV Input CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 49 Friday, February 15, 2008 1:17 PM First Time Setup—Continued 5 Enter Enter 6 Enter Enter Use the Up and Down [ ]/[ ] buttons to select “Resolution,” and use the Left and Right [ ]/[ ] buttons to select: Through: Select this to pass video through the AV receiver at the same resolution and with no conversion (default). Auto: Select this to have the AV receiver automatically convert video at resolutions not supported by your TV.
DTR-8.8_En.book Page 50 Friday, February 15, 2008 1:17 PM First Time Setup—Continued 3 HDMI Input Setup 1 2 DVD VCR Zone3 3 Remote Mode Enter Zone2 CD CDR/MD/Dock TV Cable Net/USB SAT 2, 3 Top Men Men u CH Enter Prev CH Gu id Se 1-2.
DTR-8.8_En.book Page 51 Friday, February 15, 2008 1:17 PM First Time Setup—Continued Component Video Input Setup 11 --/--- 10 Input Selector 2 12 Enter Macro 1 2 DVD VCR TV Cable Zone3 3 Remote Mode Use the Up and Down [ ]/[ ] buttons to select “1. Input/Output Assign,” and then press [Enter]. The Input/Output Assign menu appears.
DTR-8.8_En.book Page 52 Friday, February 15, 2008 1:17 PM First Time Setup—Continued Changing the Input Display Digital Input Setup If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT jacks, or connect an RI Dock to the GAME/TV jacks, for to work properly, you must change this setting. +10 Clear 12 Macro 1 2 DVD VCR Zone3 3 Remote Mode Zone2 CD CDR/MD/Dock TV This setting can only be changed on the AV receiver.
DTR-8.8_En.book Page 53 Friday, February 15, 2008 1:17 PM First Time Setup—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “4. Digital Input,” and then press [Enter]. The Digital Input menu appears. Analog Input Setup On Standby DVD VCR/DVR TV 1-4.
DTR-8.8_En.book Page 54 Friday, February 15, 2008 1:17 PM First Time Setup—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “5. Analog Input,” and then press [Enter]. The Analog Input menu appears. 1-5.Analog Input Multich DVD Enter 4 Enter 5 Se Use the Left and Right [ ]/[ ] buttons to select an input selector. You can assign the multichannel input to the following input selectors: DVD, VCR/DVR, CBL/SAT, GAME/TV, AUX 1, AUX 2, TAPE, CD, or PHONO. Press the [Setup] button.
DTR-8.8_En.book Page 55 Friday, February 15, 2008 1:17 PM First Time Setup—Continued Using Audyssey MultEQ XT Automatic Speaker Setup (Audyssey MultEQ XT) With the supplied speaker setup microphone, Audyssey MultEQ XT can measure the number of speakers connected, their sizes, crossover frequencies, and distances from the listening position and calculate the optimal speaker settings for you automatically. Before using this function, connect and position all of your speakers.
DTR-8.8_En.book Page 56 Friday, February 15, 2008 1:17 PM First Time Setup—Continued The onscreen menus shown in this manual may be slightly different from what you see on your TV. 4 The speaker detect results appear. Enter 1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected. Auto Speaker Setup Next Retry Cancel :Yes 2 Place the setup microphone at the 1st measurement position, and connect it to the Setup Mic jack.
DTR-8.8_En.book Page 57 Friday, February 15, 2008 1:17 PM First Time Setup—Continued 7 After the 3rd or 7th measurement, the following screen appears. Enter Review SP Distance: Review the speaker distance settings (see “Reviewing the Results” on page 59). Review SP Level: Review the speaker level settings (see “Reviewing the Results” on page 59). Cancel: Cancel the automatic speaker setup.
DTR-8.8_En.book Page 58 Friday, February 15, 2008 1:17 PM First Time Setup—Continued ❑ Speaker Detect Error Auto Speaker Setup Retry Cancel Auto Speaker Setup Retry Cancel :Yes :No :Yes :--- :Error :--- Speaker Detect Error This message appears if a speaker is not detected. “Yes” means that a speaker was detected. “No” means that no speaker was detected. Check your speaker connections and retry, or cancel the automatic speaker setup.
DTR-8.8_En.book Page 59 Friday, February 15, 2008 1:17 PM First Time Setup—Continued Changing the Speaker Settings Manually Reviewing the Results Enter Use the Up and Down [ ]/[ ] buttons to select the settings that you want to review, and then press [Enter]. Auto Speaker Setup Enter AUDYSSEY Save Review SP Config Review SP Distance Review SP Level Cancel The options are: Review SP Config Review the speaker configuration settings.
DTR-8.8_En.book Page 60 Friday, February 15, 2008 1:17 PM First Time Setup—Continued TV Format Setup (not North American models) 3 Enter Use the Up and Down [ ]/[ ] buttons to select “2. OSD Setup,” and then press [Enter]. The OSD Setup menu appears. 6-2.OSD Setup On Standby DVD VCR/DVR TV Input CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 61 Friday, February 15, 2008 1:17 PM First Time Setup—Continued AM Frequency Step Setup (on some models) 3 Enter Use the Up and Down [ ]/[ ] buttons to select “3. Tuner,” and then press [Enter]. The Tuner menu appears. 7-3.Tuner On Standby DVD VCR/DVR AM Freq Step TV 9kHz Input CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Enter CD Tuner 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 62 Friday, February 15, 2008 1:17 PM Playing Your AV Components Basic AV Receiver Operation On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - TV Input 3 1 Tape CD Tuner 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 63 Friday, February 15, 2008 1:17 PM Listening to the Radio ■ Manual Tuning Mode Listening to AM/FM Stations Tuning Mode Tuning 1 Press the [Tuning Mode] button so that the AUTO indicator disappears from the display. 2 Press and hold the Tuning Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the button repeatedly to change the frequency one step at a time.
DTR-8.8_En.book Page 64 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued ■ Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. On Standby DVD VCR/DVR Displaying AM/FM Radio Information Display TV Input Number buttons CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape CD Tuner 7 8 9 Phono Net/USB D.TUN +10 0 Clear 11 --/--- 10 Input Selector TV VOL D.
DTR-8.8_En.book Page 65 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Using RDS (not North American model) RDS only works in areas where RDS broadcasts are available. When tuned to an RDS station, the RDS indicator appears.
DTR-8.8_En.book Page 66 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Displaying Radio Text (RT) 4 To start the search, press [Enter]. The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search. 5 When a station you want to listen to is found, press [Enter]. If no stations are found, the message “Not Found” appears.
DTR-8.8_En.book Page 67 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Listening to HD Radio™ Stations (North American model only) HD Radio technology brings digital radio to conventional analog AM and FM radio stations, with improved sound quality, better reception, and new data services. HD Radio technology provides CD-quality sound for FM stations and FM-quality sound for AM stations.
DTR-8.8_En.book Page 68 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Selecting Multicast Channels Displaying HD Radio Information FM HD Radio stations can transmit multiple programs on the same frequency by using what are called multicast channels. If the current HD Radio station is broadcasting multicast channels, the SPS (secondary program services) indicator lights up. Press the [Display] button repeatedly to cycle through the available information.
DTR-8.8_En.book Page 69 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Listening to XM Satellite Radio® (North American Model Only) Important XM Radio Information XM Satellite Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk and entertainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
DTR-8.8_En.book Page 70 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “3. Tuner,” and then press [Enter]. The Tuner screen appears. Standby DVD VCR/DVR TV Input Number buttons 7-3.Tuner Satellite Radio On 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape None Tuner Enter CBL/SAT CD Tuner 7 8 9 Phono Net/USB D.TUN +10 0 Clear 11 --/--- 10 Input Selector TV VOL D.
DTR-8.8_En.book Page 71 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 2 To sign up, go to: http://activate.xmradio.com Or call: 1-800-967-2346 For XM Canada, go to: http://xmradio.ca Or call: 1-877-438-9677 ■ Category Search Mode 1 Press the [Receiver] Remote Mode button, and then press the [Enter] button repeatedly to select Category Search mode. Receiver Enter Notes: • RADIO ID cannot be selected in Category Search mode. You must select Channel Search mode (see right column).
DTR-8.8_En.book Page 72 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Tuning Memory Enter / Return Displaying XM Radio Information AV receiver Press the [Display] button repeatedly to cycle through the available information.
DTR-8.8_En.book Page 73 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “4. Satellite Radio,” and then press [Enter]. The Satellite Radio screen appears. The name of the currently selected input selector is displayed in a box. Enter 4 Position the XM Mini-Tuner Antenna so that as many bars as possible (up to 3) appear on the XM Satellite signal strength meter.
DTR-8.8_En.book Page 74 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Listening to SIRIUS Satellite Radio® (North American Models Only) Important SIRIUS Satellite Radio Information SIRIUS is available in the US for subscribers with addresses in the continental US and is available in Canada for subscribers with a Canadian address. To Get SIRIUS Satellite Radio a subscription and compatible tuner and antenna are required and sold separately. Visit sirius.
DTR-8.8_En.book Page 75 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Tuning Enter / 3 Enter Use the Up and Down [ ]/[ ] buttons to select “3. Tuner,” and then press [Enter]. The Tuner screen appears. 7-3.Tuner Satellite Radio None Enter Tuner Setup 4 On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 76 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Signing Up for SIRIUS Satellite Radio Before you can use SIRIUS Satellite Radio, you must first sign up for an account. You’ll need a major credit card and your SIRIUS Satellite Radio ID, which you can get from the AV receiver, as explained below, or from the SiriusConnect Home tuner package.
DTR-8.8_En.book Page 77 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 2 DVD VCR/DVR CBL/SAT 1 2 3 Game/TV AUX 1 AUX 2 4 5 6 Tape Tuner CD 7 8 9 Net/USB D.TUN 0 Clear 11 12 Within 8 seconds, use the number buttons to enter the channel number. For example, to select channel #20, press 0, 2, 0, or 2, 0, [Enter].
DTR-8.8_En.book Page 78 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 4 Press the [D.TUN] button, and then use the number buttons to enter the 4-digit PIN number. D.TUN 8 Press the [Setup] button. Setup closes. Se tu p Clear Or DVD VCR/DVR CBL/SAT 1 2 3 Game/TV AUX 1 AUX 2 4 5 6 Tape Tuner CD 7 8 9 Net/USB D.TUN 0 Clear 11 12 Use the Left and Right [ ]/[ ] buttons to select a number on the screen, and then press [Enter].
DTR-8.8_En.book Page 79 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 2 Use the Up and Down [ ]/[ ] buttons to select “4. Source Setup,” and then press [Enter]. The Source Setup menu appears. Enter 5 Use the Up and Down [ ]/[ ] buttons to select “Edit Code,” and then press [Enter]. The New Code screen appears. Enter 4-5.SIRIUS Parental Lock 4.Source Setup DVD 1.IntelliVolume 2.A/V Sync 3.Name Edit 4.Satellite Radio 5.
DTR-8.8_En.book Page 80 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Tuning Enter / Positioning the SiriusConnect Home Antenna You can check the strength of the SIRIUS Satellite Radio signal and adjust the position of the SiriusConnect Home antenna accordingly. On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 81 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued 4 Position the SiriusConnect Home antenna so that as many bars as possible (up to 3) appear on the SIRIUS Satellite signal strength meter. 4-4.SAT Radio SIRIUS Antenna Aiming Satellite SIRIUS ID Terrestrial 000000000000 If you cannot receive a satellite signal, position the SiriusConnect Home antenna so that as many bars as possible (up to 3) appear on the SIRIUS Terrestrial signal strength meter.
DTR-8.8_En.book Page 82 Friday, February 15, 2008 1:17 PM Listening to the Radio—Continued Presetting AM, FM, XM, and SIRIUS Stations Selecting Presets Preset On Standby DVD VCR/DVR TV Input 2, 4 3 CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape CD Tuner 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 83 Friday, February 15, 2008 1:17 PM Common Functions This section explains functions that can be used with any input source. Game/TV AUX 1 AUX 2 TV CH - 4 5 6 Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 84 Friday, February 15, 2008 1:17 PM Common Functions—Continued Using the Sleep Timer Displaying Source Information With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. Sleep Press the remote controller’s [Sleep] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown.
DTR-8.8_En.
DTR-8.8_En.book Page 86 Friday, February 15, 2008 1:17 PM Common Functions—Continued Using the Late Night Function On Standby With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone. TV Input DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH - 4 5 6 Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 87 Friday, February 15, 2008 1:17 PM Common Functions—Continued Tone Control Settings You can adjust the tone (bass and treble) of the front, center, surround, and surround back speakers individually. For the subwoofer, you can adjust the bass. ■ Bass You can boost or cut low-frequency sounds from –10 dB to +10 dB in 1 dB steps. ■ Treble You can boost or cut high-frequency sounds from –10 dB to +10 dB in 1 dB steps.
DTR-8.8_En.book Page 88 Friday, February 15, 2008 1:17 PM Using the Listening Modes Selecting the Listening Modes Selecting with the Remote Controller Top For a description of each listening mode, see “About the Listening Modes” on page 93. CH • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).
DTR-8.8_En.book Page 89 Friday, February 15, 2008 1:17 PM Using the Listening Modes—Continued Listening Modes Available for Each Source Format Analog and PCM Sources PCM Source format 32–96 kHz Media Button [Direct] Listening Mode CD, TV, radio ✔ ✔ Direct [Stereo] Stereo Multi channel 176.4/ 192kHz*1 analog ✔ ✔ Multichannel PCM except */2 DVD ✔ 176.
DTR-8.8_En.book Page 90 Friday, February 15, 2008 1:17 PM Using the Listening Modes—Continued DSD, Dolby Digital, and Dolby Digital Plus Sources DSD*1 Multichannel Source format 3/2 Media Button Listening Mode [Direct] Direct [Stereo] Stereo 2ch Dolby D Multichannel except */2 */2 SACD ✔*2 ✔ Dolby Digital Plus Multichannel 2ch 1/0, 1+1 except */2 DVD, DTV, etc.
DTR-8.8_En.book Page 91 Friday, February 15, 2008 1:17 PM Using the Listening Modes—Continued TrueHD and DTS Sources TrueHD*1 Multichannel except */2 */2 Source format Media Button Listening Mode [Direct] Direct [Stereo] Stereo DTS, DTS96/24 2ch 1/0, 1+1 except */2 ✔ ✔ ✔ ✔ 2ch */2 Blu-ray, HD DVD ✔ ✔ 1/0 DTS-ES Discrete/ Matrix ✔ ✔ ✔ ✔ Multichannel DVD, CD, etc.
DTR-8.8_En.
DTR-8.8_En.book Page 93 Friday, February 15, 2008 1:17 PM Using the Listening Modes—Continued About the Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Dolby Digital Plus Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest multichannel audio format from Dolby. It supports up to 7.
DTR-8.8_En.book Page 94 Friday, February 15, 2008 1:17 PM Using the Listening Modes—Continued DTS-HD Master Audio Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc formats, this new DTS format offers up to 7.1 discrete channels of uncompressed digital audio with 96 kHz/24-bit sampling rate and signal resolution. The AV receiver supports 7.1-channel sources up to 96 kHz and 5.1-channel sources up to 192 kHz. Neural THX 5.1/7.
DTR-8.8_En.book Page 95 Friday, February 15, 2008 1:17 PM Recording This section explains how to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded. • Various restrictions apply to digital recording. Refer to the manuals supplied with your digital recording equipment for more details.
DTR-8.8_En.book Page 96 Friday, February 15, 2008 1:17 PM Onscreen Setup Menus The onscreen setup menus appear on the connected TV and provide a convenient way to change the AV receiver’s various settings. Settings are organized into eight categories on the main menu, most containing a submenu. Menu 1.Input/Output Assign 2.Speaker Setup 3.Audio Adjust 4.Source Setup 5.ListeningMode Preset 6.Miscellaneous 7.Hardware Setup 8.
DTR-8.8_En.book Page 97 Friday, February 15, 2008 1:17 PM Adjusting the Listening Modes Audio Adjust With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. 1 Receiver Se Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen. Direct Setting Delay Enable ■ DSD This setting determines whether or not DSD (SACD) audio signals are passed through the DSP for A/V Sync, delay, etc.
DTR-8.8_En.book Page 98 Friday, February 15, 2008 1:17 PM Adjusting the Listening Modes—Continued ■ Dimension With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. It can be adjusted from –3 to +3. The default value is 0. Lower settings move the sound field forward. Higher settings move it backward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance.
DTR-8.8_En.book Page 99 Friday, February 15, 2008 1:17 PM Adjusting the Listening Modes—Continued Listening Mode Presets 2 On the Listening Mode Preset menu, you can specify a default listening mode for each of the audio formats supported by each input selector. The AV receiver will then select the listening mode automatically depending on the format of the input signal.
DTR-8.8_En.book Page 100 Friday, February 15, 2008 1:17 PM Adjusting the Listening Modes—Continued D.F. 2ch: Specifies the default listening mode for 2-channel (2/0) stereo sources in a digital format, such as Dolby Digital or DTS. D.F. Mono: Specifies the default listening mode for mono sources in a digital format, such as Dolby Digital or DTS. Multich PCM: Specifies the default listening mode for multichannel PCM sources, such as DVD-Audio (input via HDMI). 192/176.
DTR-8.8_En.book Page 101 Friday, February 15, 2008 1:17 PM Advanced Setup Speaker Setup 1 This section explains items on the Speaker Config menu. Receiver Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 55). Se / Input Selector Macro 1 2 DVD VCR TV Cable Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen.
DTR-8.8_En.book Page 102 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued 5 Enter Use the Up and Down [ ]/[ ] buttons to select “Front,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency. Note: • Fixed at Full Band if Subwoofer (step 4) is set to No. 8 Enter Enter 6 Enter Enter 7 Enter Enter 102 Enter Use the Up and Down [ ]/[ ] buttons to select “Center,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency.
DTR-8.8_En.book Page 103 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Low-Pass Filter for the LFE Channel Double Bass This setting is not set automatically by the Automatic Speaker Setup function (see page 55). This setting is not set automatically by the Automatic Speaker Setup function (see page 55). With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum.
DTR-8.8_En.book Page 104 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Speaker Distance 4 These settings are set automatically by the Automatic Speaker Setup function (see page 55). Enter With the Speaker Distance settings, you can specify the distance from each speaker to the listening position. 1 Receiver Se Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen.
DTR-8.8_En.book Page 105 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Speaker Level Calibration 4 These settings are set automatically by the Automatic Speaker Setup function (see page 55). With the Level Calibration settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listening position. Note: • The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82).
DTR-8.8_En.book Page 106 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Equalizer Settings 4 These settings are set automatically by the Automatic Speaker Setup function (see page 55). Enter With the Equalizer settings, you can adjust the tone of speakers individually with a 15-band equalizer. The volume of each speaker can be set on page 105. 1 Receiver Se Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen.
DTR-8.8_En.book Page 107 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued 7 Enter Use the Up [ ] button to select “Channel” again, and use the Left and Right [ ]/[ ] buttons to select another speaker. Repeat steps 6 and 7 for each speaker. 2 Enter Use the Up and Down [ ]/[ ] buttons to select “2. Speaker Setup,” and then press [Enter]. The Speaker Setup menu appears. 2.Speaker Setup Enter Enter 3 8 Press the [Setup] button. Setup closes. Se Enter 1.Speaker Settings 2.Speaker Config 3.
DTR-8.8_En.book Page 108 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued 5 Use the Up and Down [ ]/[ ] buttons to select “THX Subwoofer,” and use the Left and Right [ ]/[ ] buttons to select: No: Select this if you do not have a THX-certified subwoofer. Yes: Select this if you have a THXcertified subwoofer. Enter 2 Se Press the [Setup] button. The main menu appears onscreen.
DTR-8.8_En.book Page 109 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued 6 Se When you’ve finished, press the [Setup] button. Setup closes. tu p Name Edit You can enter a custom name for each individual input selector and radio preset for easy identification. When selected, the custom name will appear on the display. 1 Select the input selector to which you want to give a custom name. To name a radio preset, use the [Tuner] button to select AM or FM, and then select the preset.
DTR-8.8_En.book Page 110 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued 5 Enter Use the Up and Down [ ]/[ ] buttons to select “Display,” and use the Left and Right [ ]/[ ] buttons to select: Default: The default name is displayed. Custom: The custom name is displayed. Enter When Default is selected, the station’s frequency appears on the display when a radio preset is selected. 6 Enter Press the Down [ ] button to select “Name,” and then press [Enter] to open the character input screen.
DTR-8.8_En.book Page 111 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Miscellaneous Setup 4 This section explains items on the Miscellaneous menu. Enter +10 0 Clear 11 --/--- 10 Input Selector 12 Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it. The items are explained below.
DTR-8.8_En.book Page 112 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued ■ Power On Volume This setting determines what the volume will be each time the AV receiver is turned on. When the Volume Display preference is set to Absolute, the range is Last, Min, 1 to Max. When it’s set to Relative, the range is Last, –∞ dB, –81 dB to +18 dB. To use the same volume level as when the AV receiver was last turned off, select Last.
DTR-8.8_En.book Page 113 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Hardware Setup 4 Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it. The items are explained below. This section explains items on the Hardware menu. Enter Remote indicator On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH - TV Input Number buttons 4 5 6 Tape Tuner CD 7 8 9 Phono Net/USB D.
DTR-8.8_En.book Page 114 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued Tuner ■ AM Freq Step (on some models) See “AM Frequency Step Setup (on some models)” on page 61. ■ Satellite Radio (on North American model) If you connect an XM Satellite Radio antenna or SIRIUS Satellite Radio antenna to the AV receiver (both sold separately), set this setting to XM or SIRIUS respectively. If you connect both types of antenna, select XM/SIRIUS. Otherwise, select None.
DTR-8.8_En.book Page 115 Friday, February 15, 2008 1:17 PM Advanced Setup—Continued • HDMI power control only works with HDMI-compatible components that support it and may not work properly with some components due to their settings or compatibility. • When set to Enable, the AV receiver consumes more power. • When set to Enable, the AV receiver enters Ready mode when set to Standby, and the Ready indicator lights up instead of the Standby indicator (not North American model).
DTR-8.8_En.book Page 116 Friday, February 15, 2008 1:17 PM Net/USB About Net/USB The AV receiver is network-ready, which means you can hook it up to your home network with a standard Ethernet cable and enjoy the music files stored on your computer or media server. If your network is connected to the Internet, you can also enjoy Internet radio. Net/USB can also be used to play music files stored on USB mass storage devices (e.g.
DTR-8.8_En.book Page 117 Friday, February 15, 2008 1:17 PM Net/USB—Continued Minimum system requirements for Windows Media® Player 11 (for Windows® XP) Operating system Windows® XP Home Edition (SP2), Windows® XP Professional (SP2), Windows® XP Tablet PC Edition (SP2), Update Rollup 2 for Windows® XP Media Center Edition 2005 (KB900325), October 2006 Update Rollup for Windows® XP Media Center Edition (KB925766) Processor: 233 MHz Intel® Pentium ®II, Advanced Micro Devices (AMD), etc.
DTR-8.8_En.book Page 118 Friday, February 15, 2008 1:17 PM Net/USB—Continued Playing Music Files on a Server This section explains how to play music files on a computer or media server through the AV receiver. See page 116 for details on supported music servers and music file formats. 1 Start your computer or media server. 2 Press the [Receiver] Remote Mode button, followed by the [Net/USB] Input Selector button to select the Server screen.
DTR-8.8_En.book Page 119 Friday, February 15, 2008 1:17 PM Net/USB—Continued Windows Media® Player 11 Setup This section explains how to configure Windows Media® Player 11 so that the AV receiver can play the music files stored on your computer. 1 Start Windows Media® Player 11. 2 On the Library menu, select Media Sharing. The Media Sharing dialog box appears. 3 Select the Share my media check box, and then click OK. A list of supported devices appears.
DTR-8.8_En.book Page 120 Friday, February 15, 2008 1:17 PM Net/USB—Continued 3 Net/USB 4 Enter Press the [Net/USB] Remote Mode button to select the Net/USB remote controller mode. Use the Up and Down [ ]/[ ] buttons to select a USB mass storage device, and then press [Enter]. A list of the device’s contents appears. USB Storage Enter 1/15 Folder1 Folder2 01_Song_Track1.WMA 02_Song_Track2.WMA 03_Song_Track3.WMA 04_Song_Track4.WMA 05_Song_Track5.WMA 06_Song_Track6.WMA 07_Song_Track7.
DTR-8.8_En.book Page 121 Friday, February 15, 2008 1:17 PM Net/USB—Continued • Song ID information, such as album name, artist, etc., cannot be displayed on the AV receiver. • The total playing time cannot be displayed on the AV receiver. • Playback from a memory card that’s inserted in a USB card reader may not work properly. • Depending on the USB mass storage device, issues such as not being able to read the device’s contents properly, and not being able to supply power properly may occur.
DTR-8.8_En.book Page 122 Friday, February 15, 2008 1:17 PM Net/USB—Continued 5 Press [Enter]. The station’s programs are displayed. Enter 6 Enter Use the Up and Down [ ]/[ ] buttons to select a program, and then press [Enter]. Playback starts and the following screen appears. PLAY Enter This section explains how to configure the AV receiver’s network settings manually.
DTR-8.8_En.book Page 123 Friday, February 15, 2008 1:17 PM Net/USB—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “6. Network,” and then press [Enter]. The Network screen appears. 7-6.Network MAC Adress Control Port Enter 4 Enter 5 Enter ■ Port This is the network port used for control over the network. DHCP 00:00:00-00:00:00 Disable --- Use the Up and Down [ ]/[ ] buttons to select the settings, and use the Left and Right [ ]/[ ] buttons to set them.
DTR-8.8_En.book Page 124 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3 In addition to your main listening room, you can also enjoy playback in two other rooms, or as we call them, Zone 2 and Zone 3. And, you can select a different source for each room. Connecting Your Zone 2 Speakers to an Amp in Zone 2 Connecting Zone 2 There are two ways you can connect Zone 2 speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an amp in Zone 2.
DTR-8.8_En.book Page 125 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Zone 2 Video Outputs Connecting Zone 3 The AV receiver features a composite video output and component video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone. Hookup • Use a composite video cable to connect the AV receiver’s ZONE 2 OUT V jack to a composite video input on your Zone 2 TV.
DTR-8.8_En.book Page 126 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Powered Zone 2 Setting 3 If you’ve connected your Zone 2 speakers to the AV receiver, as explained in “Connecting Your Zone 2 Speakers Directly to the AV receiver” on page 124, you must set the Powered Zone 2 setting to Act (Activated). Enter Use the Up and Down [ ]/[ ] buttons to select “2. Zone 2/ Zone 3,” and then press [Enter]. The Zone 2/Zone 3 screen appears. 7-2.
DTR-8.8_En.book Page 127 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Zone 2/Zone 3 Out Settings 5 If you’ve connected your Zone 2 or Zone 3 speakers to an amp with no volume control, set the Zone 2 Out or Zone 3 Out setting, respectively, to Variable so that you can set the zone’s volume, balance, and tone on the AV receiver. 1 Receiver Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen. Press the [Setup] button. Setup closes.
DTR-8.8_En.book Page 128 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Selecting an Input Source for Zones 1 On the remote controller, press the [Zone 2] or [Zone 3] Remote Mode button. The [Zone2] or [Zone3] Remote Mode button lights up. Remote controller Zone3 • On the North American model, you can select a different radio source for each room. For example, XM for your main room, SIRIUS for Zone 2, and AM/FM for Zone 3.
DTR-8.8_En.book Page 129 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Adjusting the Volume of Zones Remote controller Zone3 Zone2 Level- Level+ On the remote controller, press the [Zone 2] or [Zone 3] Remote Mode button, and then use the [Level–] and [Level+] buttons. On the AV receiver, press the [Zone 2] or [Zone 3] button, and then use the Level Up and Down [ ]/[ ] buttons.
DTR-8.8_En.book Page 130 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Using the 12V Triggers 3 The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for the main room, Zone 2, Zone 3, or any combination of rooms.
DTR-8.8_En.book Page 131 Friday, February 15, 2008 1:17 PM Zone 2 and Zone 3—Continued Using the Remote Controller in Zone 2/3 and Multiroom Control Kits To control the AV receiver with the remote controller while you’re in Zone 2 or Zone 3, you’ll need a commercially available multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech.
DTR-8.8_En.book Page 132 Friday, February 15, 2008 1:17 PM Controlling Other Components You can control your other components, including those made by other manufacturers, with the remote controller. This section explains how to: • Enter the remote control code for a component that you want to control: DVD, TV, VCR, etc. • Learn commands directly from another component’s remote controller (see page 135). • Program the Macro buttons to perform a sequence of up to eight remote control actions (see page 136).
DTR-8.8_En.book Page 133 Friday, February 15, 2008 1:17 PM Controlling Other Components—Continued Remote Control Codes for Integra/Onkyo Components Connected via Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 2 Make sure the Integra/Onkyo component is connected with an cable and an analog audio cable (RCA). See page 45 for details.
DTR-8.8_En.book Page 134 Friday, February 15, 2008 1:17 PM Controlling Other Components—Continued To control another component, point the remote controller at it and use the buttons explained below. (You must select the appropriate remote controller mode with the Remote Mode buttons first.) With some components, certain buttons may not work as expected, and some may not work at all.
DTR-8.8_En.book Page 135 Friday, February 15, 2008 1:17 PM Controlling Other Components—Continued 3 E EV ST E TEON T L SE H C PE TA C IS D VID EO -1 D C O N R O T TO H SE C P ER E LE R N PR SE E TU T UN PU T IN P U PE O R TA G VD D -2 EO VID IM D P VD EE D PO D D nd R/D 4 TV DC e/ I T 3 SA V L/ T CB 6 X2 t Inpu 8 V C - H T V UN D.
DTR-8.8_En.book Page 136 Friday, February 15, 2008 1:17 PM Controlling Other Components—Continued Using Macros You can program the remote controller’s Macro buttons to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the following actions: 1. Press the [Receiver] Remote Mode button to select the Receiver remote controller mode. 2. Press the [On] button to turn on the AV receiver. 3. Press the [CD] Input Selector button to select the CD input source. 4.
DTR-8.8_En.book Page 137 Friday, February 15, 2008 1:17 PM Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased this unit.
DTR-8.8_En.book Page 138 Friday, February 15, 2008 1:17 PM Troubleshooting—Continued The subwoofer produces no sound • If the source material contains no audio in the LFE channel, the subwoofer produces no sound. • Check the Speaker Configuration (page 101). The Zone 2/3 speakers produce no sound • The Zone 2/3 speakers only output sources that are connected to an analog input. Check to see if the source component is connected to an analog input.
DTR-8.8_En.book Page 139 Friday, February 15, 2008 1:17 PM Troubleshooting—Continued Tuner Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t light up • Relocate your antenna. • Move the AV receiver away from your TV or computer. • Listen to the station in mono (page 63). • When listening to an AM station, operating the remote controller may cause noise. • Passing cars and airplanes can cause interference. • Concrete walls weaken radio signals.
DTR-8.8_En.book Page 140 Friday, February 15, 2008 1:17 PM Troubleshooting—Continued USB Mass Storage Device Playback Can’t access the music files on a USB device • Make sure the USB device is plugged in properly. • The AV receiver supports USB devices that support the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.
DTR-8.8_En.book Page 141 Friday, February 15, 2008 1:17 PM Specifications Amplifier Section General Rated Output Power North American: 140 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20Hz to 20kHz, with a maximum total harmonic distortion of 0.05% (FTC) 170 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1kHz, with a maximum total harmonic distortion of 0.
DTR-8.8_En.
DTR-8.8_En.
DTR-8.8_En.book Page 144 Friday, February 15, 2008 1:17 PM Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 En I0801-2 SN 29344544A (C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
