DTR-6.5,5.5_En.book Page 1 Wednesday, July 28, 2004 9:07 AM AV Receiver DTR-6.5/5.
DTR-6.5,5.5_En.book Page 2 Wednesday, July 28, 2004 9:07 AM WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DTR-6.5,5.5_En.book Page 3 Wednesday, July 28, 2004 9:07 AM Precautions For U.S. Models Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
DTR-6.5,5.5_En.book Page 4 Wednesday, July 28, 2004 9:07 AM Supplied Accessories Precautions—Continued Make sure you have the following accessories: For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
DTR-6.5,5.5_En.book Page 5 Wednesday, July 28, 2004 9:07 AM Features DTR-6.5/5.5 DTR-6.5 Amplifier Amplifier • • • • • • • 100 watts per channel into 8 ohms, 20 Hz to 20 kHz, less than 0.
DTR-6.5,5.5_En.book Page 6 Wednesday, July 28, 2004 9:07 AM Table of Contents Basic Introduction Important Safety Instructions ..........................................................................................2 Precautions .......................................................................................................................3 Supplied Accessories.......................................................................................................4 Features .........................
DTR-6.5,5.5_En.book Page 7 Wednesday, July 28, 2004 9:07 AM Table of Contents—Continued Advanced Introduction ............................... 2 Connections ............................ 21 First Setup ............................... 39 Controlling Other Components Advanced Features Entering a Remote Control Codes................................. 80 Learning Commands from Another Remote Controller ..................................................................... 88 Using Macros.......................
DTR-6.5,5.5_En.book Page 8 Wednesday, July 28, 2004 9:07 AM Front & Rear Panels Front Panel DTR-6.5 1 2 3 4 5 6 789 J K L MN O P Q R S T Zone 2 Standby U V W X Y Z DTR-5.
DTR-6.5,5.5_En.book Page 9 Wednesday, July 28, 2004 9:07 AM Front & Rear Panels—Continued For detailed information, see the pages in parentheses. A Standby/On button (38) This button is used to set the AV receiver to On or Standby. For models with a POWER switch, this button has no effect unless the POWER switch is set to ON. B Standby indicator (38) This indicator lights up when the AV receiver is in Standby mode, and it flashes while a signal is being received from the remote controller.
DTR-6.5,5.5_En.book Page 10 Wednesday, July 28, 2004 9:07 AM Front & Rear Panels—Continued Display 1 23 4 6 5 7 AUTO: This indicator lights up when the Auto Tuning mode is selected, and disappears when the Manual Tuning mode is selected. For detailed information, see the pages in parentheses. 1 MUTING indicator (54) This indicator flashes while the AV receiver is muted. MEMORY: This indicator lights up when presetting radio stations.
DTR-6.5,5.5_En.book Page 11 Wednesday, July 28, 2004 9:07 AM Front & Rear Panels—Continued DTR-5.
DTR-6.5,5.5_En.book Page 12 Wednesday, July 28, 2004 9:07 AM Front & Rear Panels—Continued J OPTICAL DIGITAL (27, 28, 30, 32, 34, 35) V DVD IN (28, 29) The DTR-5.5 doesn’t have an IN 4 jack. Here you can connect a DVD player. Input jacks include S-Video, composite video, and analog audio. You can connect a DVD player’s 2-channel analog audio output or 5.1-channel analog audio output.
DTR-6.5,5.5_En.book Page 13 Wednesday, July 28, 2004 9:07 AM Remote Controller Installing the Batteries 1 To open the battery compartment, press the small hollow and slide off the cover. Using the Remote Controller To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below. Remote control sensor AV receiver 2 3 Put the cover onto the remote controller and slide it shut. Notes: • The batteries should last for about six months, although this will vary with usage.
DTR-6.5,5.5_En.book Page 14 Wednesday, July 28, 2004 9:07 AM Remote Controller—Continued In addition to controlling the AV receiver, the remote controller has several operating modes for controlling your other AV components, including Integra components connected via . Modes are selected by using the remote controller’s Remote Mode buttons. For detailed information, see the pages in parentheses. Some of the functions described in this manual may not work as expected with other components.
DTR-6.5,5.5_En.book Page 15 Wednesday, July 28, 2004 9:07 AM Remote Controller—Continued Pure A button This button is used to select the Pure Audio listening mode. Direct button This button is used to select the Direct listening mode.
DTR-6.5,5.5_En.book Page 16 Wednesday, July 28, 2004 9:07 AM Remote Controller—Continued DVD Mode 1A B On Standby TV I V1 23 DVD mode is used to control an Integra DVD player connected to the AV receiver via . To set the remote controller to DVD mode, press the [DVD] Remote Mode button. A Standby button This button is used to set the DVD player to Standby.
DTR-6.5,5.5_En.book Page 17 Wednesday, July 28, 2004 9:07 AM Remote Controller—Continued N A-B button This button is used to set the A–B repeat playback function. O Open/Close [ ] button This button is used to open and close the disc tray. P Video Off button This button is used to turn off the internal video circuitry, eliminating any possibility of interference. Q Clear button This button is used to cancel functions and to clear entered numbers.
DTR-6.5,5.5_En.book Page 18 Wednesday, July 28, 2004 9:07 AM Remote Controller—Continued MD/CDR Mode On 1 Standby TV I V1 2 MD/CDR mode is used to control an Integra MiniDisc recorder or CD recorder connected to the AV receiver via . To select MD/CDR mode, press the [MD/CDR] Remote Mode button. By default, this button is set to control a MiniDisc recorder. To control a CD recorder, it must be set to CDR (see page 80).
DTR-6.5,5.5_En.book Page 19 Wednesday, July 28, 2004 9:07 AM Remote Controller—Continued M FR & FF [ ]/[ ] buttons The FR [ ] button is used to start fast reverse. The FF [ ] button is used to start fast forward. N Stop [ ] button This button is used to stop playback. O Random button This button is used with the random playback function. P Memory button This button is used with the memory playback function, which allows you to create a custom playlist of tracks.
DTR-6.5,5.5_En.book Page 20 Wednesday, July 28, 2004 9:07 AM About Home Theater Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog and digital TV you can enjoy Dolby Pro Logic IIx or Onkyo’s own DSP surround listening modes. With the DTR-6.
DTR-6.5,5.5_En.book Page 21 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver AV Connection Color Coding About AV Connections RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.
DTR-6.5,5.5_En.book Page 22 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting a Powered Subwoofer Connecting Your Speakers Speaker Configuration For the best surround-sound experience, you should connect seven speakers and a powered subwoofer. The following table indicates the channels you should use depending on the number of speakers that you have.
DTR-6.5,5.5_En.book Page 23 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Speaker Connection Precautions Read the following before connecting your speakers: • American model only: Only connect speakers with an impedance of 6 ohms or higher. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated.
DTR-6.5,5.5_En.book Page 24 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting Antenna This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.
DTR-6.5,5.5_En.book Page 25 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting an Outdoor FM Antenna Connecting an Outdoor AM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
DTR-6.5,5.5_En.book Page 26 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting Both Audio & Video By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD player, etc.
DTR-6.5,5.5_En.book Page 27 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting Your TV or Projector Monitor Out Audio Connections ■ Using Composite Video Use a composite video cable to connect the AV receiver’s V MONITOR OUT jack to a composite video input on your TV, as shown. These connections will allow you to listen to audio from your TV via the AV receiver. If your TV doesn’t have an audio output, connect the AV receiver to your VCR and use its tuner (see page 30).
DTR-6.5,5.5_En.book Page 28 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Audio Connections Connecting a DVD Player Video Connections You only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the AV receiver’s V DVD IN jack to the composite video output on your DVD player, as shown.
DTR-6.5,5.5_En.book Page 29 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued ■ Using a Multichannel Connection If your DVD player supports multichannel audio formats such as DVD-Audio, and it has a 5.1-channel analog audio output, you can enjoy DVD-Audio playback. Use a multichannel analog audio cable to connect the AV receiver’s DVD IN FRONT L/R, CENTER, SURR L/R, and SUBWOOFER jacks to the 5.1-channel analog audio output on your DVD player, as shown.
DTR-6.5,5.5_En.book Page 30 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting a VCR for Playback Connecting a D-VHS VCR for Playback This section shows how to connect a VCR for playback so that you can watch videos via the AV receiver. Video Connections • Use an S-Video cable to connect the AV receiver’s S VIDEO 1 IN jack to a S-Video output on your VCR, as shown.
DTR-6.5,5.5_En.book Page 31 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting a VCR for Recording This section explains how to connect a VCR for recording from a TV or another VCR. VCR (recording) R L R L AUDIO OUTPUT AUDIO INPUT Video Connections • Use an S-Video cable to connect the AV receiver’s S VIDEO 1 OUT jack to an S-Video input on the recording VCR.
DTR-6.5,5.5_En.book Page 32 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting Other Video Sources— Satellite, Cable, Set-top box, LD Player, etc. Video Connections ■ Using Component Video If you connect to a component video input, you must assign it (see page 43). Use a component video cable to connect the AV receiver’s COMPONENT VIDEO IN 2 or IN 3 jack to a component video output on your video source, as shown. You only need to use one of the following connection methods.
DTR-6.5,5.5_En.book Page 33 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued ■ Using Analog Connections If your video source doesn’t have a digital audio output, or you want to record from it, you’ll need to make the following analog audio connection. Use an analog audio cable to connect the AV receiver’s VIDEO 3 IN L/R jacks to the analog audio output on your video source, as shown.
DTR-6.5,5.5_En.book Page 34 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting a CD Player Connecting a Cassette Recorder ■ Using Optical or Coaxial Connections If you connect to a digital audio input, you’ll need to assign it (see page 42). • Use an optical digital audio cable to connect one of the AV receiver’s OPTICAL DIGITAL IN jacks to the optical output on your CD player, as shown.
DTR-6.5,5.5_En.book Page 35 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued ■ Using Optical or Coaxial Connections (playback only) If you connect to a digital audio input, you’ll need to assign it (see page 42). • Use an optical digital audio cable to connect one of the AV receiver’s OPTICAL DIGITAL IN jacks to the optical output on your recorder, as shown.
DTR-6.5,5.5_En.book Page 36 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting a Turntable For the DTR-6.5 The AV receiver’s PHONO IN is designed for use with a moving magnet (MM) type cartridge. Use an analog audio cable to connect the AV receiver’s PHONO IN L/R jacks to the audio output on your turntable, as shown.
DTR-6.5,5.5_En.book Page 37 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting a Power Amplifier (DTR-6.5 only) Connecting If you want to connect a more powerful power amplifier and use the AV receiver as a preamp, you can connect one to the PRE OUT jacks. In this case, you should connect all speakers and the subwoofer to that power amplifier. However, if you have a powered subwoofer, connect it to this AV receiver’s PRE OUT SUBWOOFER jack.
DTR-6.5,5.5_En.book Page 38 Wednesday, July 28, 2004 9:07 AM Connecting the AV receiver—Continued Connecting the Power Cords of Other Components The AV receiver has AC outlets on its rear panel that can be used to connect the power cords of AV other components that you intend to use with the AV receiver. These components can then be left turned on so that they turn on and off as and when the AV receiver is turned on and set to Standby.
DTR-6.5,5.5_En.book Page 39 Wednesday, July 28, 2004 9:07 AM First Time Setup This chapter explains the settings that you need to make before using the AV receiver. Automatic Speaker Setup With the supplied speaker setup microphone, the Automatic Speaker Setup function can measure the test tone output by each speaker and automatically determine the number of speakers connected, their sizes, the distance from each speaker to the listening position, and so on.
DTR-6.5,5.5_En.book Page 40 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued 3 Press [Enter]. Enter Press the [Return] button to return to the previous menu. Auto Speaker Setup -----------------------Do not Unplug Setup Mic Wait a moment, Please. 0-1.Warning -----------------------Not Connect -:-:-:--:--:--:--:-- The automatic speaker setup starts. The test tone, which is somewhat loud, is output by each speaker in turn, measured by the microphone, and the speaker settings set accordingly.
DTR-6.5,5.5_En.book Page 41 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued About the Onscreen Setup Menus The AV receiver is configured using onscreen setup menus, which are displayed on the TV that’s connected to either of the MONITOR OUT jacks. Because they appear on your TV, they’re large and clear, making setup a breeze. Settings are divided into two groups: Basic Setup and Advanced Setup.
DTR-6.5,5.5_En.book Page 42 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Initial Setup 3 Digital Input Enter If you connect a component to a digital input jack, you must assign that jack to an input selector. For example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selector. By default, the OPTICAL IN1 jack is assigned to the DVD input selector, although this can be changed.
DTR-6.5,5.5_En.book Page 43 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Component Video Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector. For example, if you connect your DVD player to COMPONENT IN 3, you should assign it to the DVD input selector. If you want to output composite and S-Video sources from the COMPONENT VIDEO OUT, select Video, as explained below.
DTR-6.5,5.5_En.book Page 44 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Minimum Speaker Impedance (not American models) 2 Enter This setting is not set automatically by the Automatic Speaker Setup function (see page 39). If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, set the Minimum Speaker Impedance to “4 ohms.” Note: Before you change this setting, turn down the volume.
DTR-6.5,5.5_En.book Page 45 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued TV Format Setup (not American models) Here you can specify the TV format used in your area. 1 Receiver Press the [Receiver] button followed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “1. Initial Setup,” and then press [Enter]. The Initial Setup menu appears. 3 Use the Up and Down [ ]/[ ] buttons to select “3. Hardware Setup,” and then press [Enter].
DTR-6.5,5.5_En.book Page 46 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Speaker Setup 2 Some of the settings in this section are set automatically by the Automatic Speaker Setup function (see page 39). Here you can check the settings made by the Automatic Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using the Automatic Speaker Setup function. Enter Use the Up and Down [ ]/[ ] buttons to select “2.
DTR-6.5,5.5_En.book Page 47 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued 6 Enter 7 Enter 8 Enter Use the Up and Down [ ]/[ ] buttons to select “c. Center,” and then use the Left and Right [ ]/ [ ] buttons to select: Small: Select if the center speaker is small. Large: Select if the center speaker is large. None: Select if no center speaker is connected. Note: • If the Front setting in step 5 is set to Small, the Large option cannot be selected.
DTR-6.5,5.5_En.book Page 48 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Double Bass This setting is not set automatically by the Automatic Speaker Setup function (see page 39). With the Double Bass function, you can boost bass output by feeding bass sounds from the front left and right channels to the subwoofer. This function can be set only if the Subwoofer setting in step 4 is set to Yes, and the Front setting in step 5 is set to Large.
DTR-6.5,5.5_En.book Page 49 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued The Speaker Distance menu appears. Menu -----------------------Basic Setup 2.Speaker Setup 1.Initial Setup -----------------------2.Speaker Setup 1.Speaker Config 2-2.Speaker Distance -----------------------2.Speaker Distance Advanced Setup a.Unit Calibration :meters 3.Level 3.Surround Setup 4.Equalizer Settings b.LeftAdjust : 3.6m 4.Audio c.Center 3.6m 5.Listening Mode :Preset d.Right : 3.6m 6.Preference e.
DTR-6.5,5.5_En.book Page 50 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Speaker Level Calibration 3 This setting is set automatically by the Automatic Speaker Setup function (see page 39). Enter Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.
DTR-6.5,5.5_En.book Page 51 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Equalizer Setting 4 This setting is set automatically by the Automatic Speaker Setup function (see page 39). Enter Here you can adjust the EQ of individual speakers. The volume of individual speakers can be set on page 50.
DTR-6.5,5.5_En.book Page 52 Wednesday, July 28, 2004 9:07 AM First Time Setup—Continued Changing the TAPE/MD/CDR Display If you connect an -compatible Integra MiniDisc recorder or CD recorder to the TAPE IN/OUT jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. Zone 2 Standby 1, 2 (DTR-6.5 shown here) 52 1 Press the [TAPE] input selector button so that “TAPE” appears on the display.
DTR-6.5,5.5_En.book Page 53 Wednesday, July 28, 2004 9:07 AM Basic Operation Selecting the Input Source This section explains how to select the input source (i.e., the AV component that you want to listen to or watch).
DTR-6.5,5.5_En.book Page 54 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued CD Tape Tuner 7 8 9 Using the Sleep Timer TV VOL Phono +10 0 With the sleep timer, you can set the AV receiver to automatically turn off after a specified period.
DTR-6.5,5.5_En.book Page 55 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued Displaying Source Information You can display various information about the current input source as follows.
DTR-6.5,5.5_En.book Page 56 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued ■ Manual Tuning Mode Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. 1 Press the [Tuning Mode] button so that the AUTO indicator disappears from the display. 2 Press and hold the Tuning Up or Down [ ]/[ ] button. The frequency stops changing when you release the button.
DTR-6.5,5.5_En.book Page 57 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued Presetting Radio Stations 2, 4 Deleting Presets 3 2 Zone 2 Zone 2 Standby Standby You can store up to 40 of your favorite radio stations as presets. 1 Tune into the station that you want to store as a preset. 2 Press the [Memory] button. The MEMORY indicator appears and the preset number flashes.
DTR-6.5,5.5_En.book Page 58 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued Selecting Listening Modes See “About the Listening Modes” on page 60 for detailed information about the listening modes. Selecting with the Remote Controller RC-585M Display Muting Rec • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial or optical).
DTR-6.5,5.5_En.book Page 59 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued The following table lists all the listening modes and shows which modes can be selected for each input signal format. Input signal format Listening mode Analog, PCM*1 Dolby D */2 Source CD, TV, LD, VHS, MD, turntable, radio, cassette, DTV, etc. 2/0 DTS/DTS 96/24*2 1/0,1+1 Other */2 DVD, DTV, etc. 2/0 1/0, 1+1 Other DTS- Multich ES DVD, LD, CD, etc.
DTR-6.5,5.5_En.book Page 60 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued About the Listening Modes Dolby Pro Logic II Music With its built-in surround-sound decoders and DSP programs, the AV receiver can transform your home listening room into a movie theater or concert hall. If you connect two surround back speakers (i.e., left and right), both will be used for 6.1-channel surround playback. Use this mode to add 5.1 surround to stereo sources such as music CDs and DVDs.
DTR-6.5,5.5_En.book Page 61 Wednesday, July 28, 2004 9:07 AM Basic Operation—Continued Onkyo Original DSP Modes DTS-ES Matrix This is DTS with an added surround back channel for 6.1 surround sound. Use it to provide 6.1 channel surround playback with program material recorded in DTS 5.1 format. Since DTS 5.1 program material contains surround back channel information, all channels can be reconstructed for 6.1-channel playback. Use this mode with CDs, DVDs, or LDs that bear the DTS-ES or DTS logo.
DTR-6.5,5.5_En.book Page 62 Wednesday, July 28, 2004 9:07 AM Advanced Operation 4 5 6 CD Tape Tuner 7 8 9 0 Clear TV VOL Phono +10 Using the Re-EQ Function (DTR-6.5 only) - With the Re-EQ function, you can correct a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing.
DTR-6.5,5.5_En.book Page 63 Wednesday, July 28, 2004 9:07 AM Advanced Operation—Continued Using the DVD Analog Multichannel Input On Standby V1 V2 TV I Multi CH 1 2 3 + V4 Multi CH DVD T V CH 4 5 6 - CD Tape Tuner 7 8 9 0 Clear TV VOL Phono +10 The DVD analog multichannel input is for connecting components with a 5.1-channel analog audio output, such as a DVD player or MPEG decoder. See “Using a Multichannel Connection” on page 29 for connection information.
DTR-6.5,5.5_En.book Page 64 Wednesday, July 28, 2004 9:07 AM Advanced Operation—Continued Recording This section explains how to record the current input source, how to record one input source while enjoying another, and how to dub audio onto your video recordings. Unless you have the full consent of the copyright holder, copyright laws prohibit using your recordings for anything other than personal enjoyment! Notes: • The surround sound and DSP listening modes cannot be recorded.
DTR-6.5,5.5_En.book Page 65 Wednesday, July 28, 2004 9:07 AM Advanced Operation—Continued AV Recording Recording Separate AV Sources You can record AV input sources to an AV recording component (VCR, etc) connected to the VIDEO 1 OUT or VIDEO 2 OUT. See pages 27–38 for information on connecting components. Here you can record audio and video from completely separate sources, allowing you to overdub audio onto your video recordings.
DTR-6.5,5.5_En.book Page 66 Wednesday, July 28, 2004 9:07 AM Advanced Setup Decoder Setup Here are surround-related settings for PCM, Dolby Digital, multichannel, and other input signal formats. 1 Receiver 2 Enter Enter 3 Enter Press the [Receiver] button followed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ ]/[ ] buttons to select “3. Decoder Setup,” and then press [Enter]. The Surround Setup menu appears. Menu -----------------------Basic Setup Setup 3.Decorder 1.
DTR-6.5,5.5_En.book Page 67 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued ■ c. SurrBack Mode This setting determines which surround mode is used for Dolby Digital input signals that don’t contain a Dolby Digital EX flag, or when the b. Dolby EX setting is set to Manual. This setting is unavailable if no surround back speakers are connected. You can select PLIIx Movie (default), PLIIx Music, or Dolby D, or Dolby D EX. • If only one surround back speaker is connected, PLIIx Movie is unavailable.
DTR-6.5,5.5_En.book Page 68 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued Audio Adjust Functions Here you can set listening mode-related settings and functions. 1 Receiver 2 Enter Press the [Receiver] button followed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ ]/[ ] buttons to select “4. Audio Adjust,” and then press [Enter]. The Audio Adjust menu appears.
DTR-6.5,5.5_En.book Page 69 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued 4-1. Mono ■ a. Output Channel This setting determines which speakers are used to output mono audio when the Mono listening mode is used. L/R: Mono audio is output from the front left and right speakers (default). Center: Mono audio is output from the center speaker. ■ b. Academy (DTR-6.
DTR-6.5,5.5_En.book Page 70 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued 4-9. Theater-Dimensional These settings apply to the Theater-Dimensional listening mode. ■ a. Listening Angle With this setting, you can specify the angle of the front left and right speakers relative to the listening position. Processing for the Theater-Dimensional listening mode is based on this setting.
DTR-6.5,5.5_En.book Page 71 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued 4 Enter 5 Use the Up and Down [ ]/[ ] buttons to select the signal format that you want to set, and then use the Left and Right [ ]/ [ ] buttons to select a listening mode. Only listening modes that can be used with each input signal format can be selected. For “Surround” or “THX,” the listening mode specified on pages 66, 67 will be used. The Last Valid option means that the listening mode selected last will be used.
DTR-6.5,5.5_En.book Page 72 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued 6-1. IntelliVolume 6-3. OSD Setup With this preference, you can set the input level for each input source. This is useful if some of your AV components are louder or quieter than others. While this preference is shown onscreen, you can select each input source and set the levels while listening to and comparing them.
DTR-6.5,5.5_En.book Page 73 Wednesday, July 28, 2004 9:07 AM Advanced Setup—Continued 6-5. Digital Format ■ b. Digital Format This setting does not apply to input selectors not assigned to a digital input jack. With this setting, you can set a digital input to DTS, PCM, or Auto. This can be set for each input selector individually.
DTR-6.5,5.5_En.book Page 74 Wednesday, July 28, 2004 9:07 AM Zone 2 Using Only Speakers in Zone 2 Connecting Zone 2 With the Zone 2 function, you can enjoy one input source in the main room and a different source in another room. There are two connection methods: using a receiver/integrated amp in Zone 2 or using only a pair of speakers in Zone 2. With this connection method, you can use 5.1 surround sound in the main room and play a different AV source in Zone 2.
DTR-6.5,5.5_En.book Page 75 Wednesday, July 28, 2004 9:07 AM Zone 2—Continued Setting the Powered Zone 2 4 To use Zone 2, you must make this setting. It enables the speakers connected to the ZONE 2 SPEAKERS terminals so that they produce sound when Zone 2 is used. 7 8 9 0 Clear Enter TV VOL Phono +10 Menu -----------------------Basic Setup 1.Initial Setup 1.Initial Setup -----------------------2.Speaker 1.DigitalSetup Input 1-3.Hardware Setup -----------------------2.
DTR-6.5,5.5_En.book Page 76 Wednesday, July 28, 2004 9:07 AM Zone 2—Continued Setting the Zone 2 Out 3 The ZONE 2 OUT L/R jacks can also be used as pre outs.
DTR-6.5,5.5_En.book Page 77 Wednesday, July 28, 2004 9:07 AM Zone 2—Continued Using Zone 2 To set Zone 2 to the same source as the main room, press the [ZONE 2] button, and then use the Controller [ ]/[ ] buttons to select “Zone 2 Sel: Source.” Here you can turn on Zone 2, select an input source, and adjust the volume.
DTR-6.5,5.5_En.book Page 78 Wednesday, July 28, 2004 9:07 AM Zone 2—Continued Using the 12V Trigger Using the Remote Control in Zone 2 When the AV receiver’s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V TRIGGER IN jack on a connected component, the AV receiver can be configured so that the component is turned on automatically when Zone 2 is used. See page 73 for details. Adjusting the Bass & Treble for Zone2 You can adjust the bass and treble for Zone2.
DTR-6.5,5.5_En.book Page 79 Wednesday, July 28, 2004 9:07 AM Zone 2—Continued Using a Multiroom Kit with a Cabinet In the following diagram, an IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver in the cabinet via the connecting block. • On the Remote Setup menu, set the IR IN Position setting to “Main” (see page 72).
DTR-6.5,5.5_En.book Page 80 Wednesday, July 28, 2004 9:07 AM Controlling Other Components You can use the AV Receiver’s remote controller (RC588M/RC-590M/RC-591M) to control your other components, including those made by other manufacturers. This chapter explains how to: • Enter the remote control code for a component that you want to control (e.g., DVD, TV, VCR). • Learn commands directly from another component’s remote controller (see page 88).
DTR-6.5,5.5_En.book Page 81 Wednesday, July 28, 2004 9:07 AM Controlling Other Components—Continued Resetting the Remote Controller Here you can reset the remote controller to its default settings. On Standby V1 V2 V3 1 2 3 + V4 Multi CH DVD T V CH - TV Standby I Input 4 5 6 CD Tape Tuner 7 8 9 0 Clear TV 1 Receiver TV VOL Phono +10 Standby --/--- While holding down the [Receiver] button, press the [Standby] button. Release both buttons and wait five seconds.
DTR-6.5,5.5_En.book Page 82 Wednesday, July 28, 2004 9:07 AM Controlling Other Components—Continued Remote Control Codes When two or more codes are given, try each one in turn, and choose the one that works best. Depending on the manufacturer and component, the remote controller may not work as expected.
DTR-6.5,5.5_En.
DTR-6.5,5.5_En.
DTR-6.5,5.5_En.
DTR-6.5,5.5_En.book Page 86 Wednesday, July 28, 2004 9:07 AM Controlling Other Components—Continued To control another component, point the remote controller at it and use the buttons as explained below (you must select the appropriate remote control mode first).
DTR-6.5,5.5_En.
DTR-6.5,5.5_En.book Page 88 Wednesday, July 28, 2004 9:07 AM Controlling Other Components—Continued Learning Commands from Another Remote Controller 3 The AV receiver’s remote controller can learn the commands of other remote controllers simply by pointing them at each other. For example, by transmitting the Play command from your CD player’s remote controller, the remote controller can learn it and then transmit the same command when its Play [ ] button is pressed in CD mode.
DTR-6.5,5.5_En.book Page 89 Wednesday, July 28, 2004 9:07 AM Controlling Other Components—Continued Using Macros With the Macro function, you can program the remote controller’s Macro buttons to perform a sequence of actions with just one button press. For example, normally you need to perform the following actions to play a CD: 1. Press the Remote Mode [Receiver] button to select Receiver mode. 2. Press the [On] button to turn on the AV receiver. 3.
DTR-6.5,5.5_En.book Page 90 Wednesday, July 28, 2004 9:07 AM Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. Power Can’t turn on the AV receiver? • Make sure that the power cord is properly plugged into the wall outlet. • Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.
DTR-6.5,5.5_En.book Page 91 Wednesday, July 28, 2004 9:07 AM Troubleshooting—Continued The subwoofer produces no sound? • When you play source material that contains no information in the LFE channel, the subwoofer produces no sound. • Make sure the speakers are configured correctly (page 46). There’s no sound with a certain signal format? • Check the digital audio output setting on the connected device. On some games consoles, such as those that support DVD, the default setting is off.
DTR-6.5,5.5_En.book Page 92 Wednesday, July 28, 2004 9:07 AM Troubleshooting—Continued Tuner Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t appear? • Relocate your antenna. • Move the AV receiver away from your TV or computer. • Listen to the station in mono (page 56). • When listening to an AM station, operating the remote controller may cause noise. • Passing cars and airplanes can cause interference. • Concrete walls weaken radio signals.
DTR-6.5,5.5_En.book Page 93 Wednesday, July 28, 2004 9:07 AM Troubleshooting—Continued Others The sound changes when I connect my headphones? • When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Direct, or Pure Audio. When you disconnect the headphones, the previous listening mode will be resumed.
7_Appendix_En Page 94 Wednesday, July 28, 2004 11:40 AM Specifications (DTR-6.
7_Appendix_En Page 95 Wednesday, July 28, 2004 11:40 AM Specifications (DTR-5.5) Amplifier Section General Power Output (2 channels driven): Power Supply Dynamic Power THD (Total Harmonic Distortion) Damping Factor Input Sensitivity and Impedance Output Level and Impeadance Frequency Response Tone Control SN Ratio Speaker Impedance 85 W + 85 W (8Ω,20Hz–20kHz, FTC) 120 W +120 W (6Ω,1kHz,DIN) 150 W + 150 W (6Ω,1kHz,JEITA) 220 W + 220 W (3Ω,Front) 165 W + 165 W (4Ω,Front) 100 W + 100 W (8Ω,Front) 0.
DTR-6.5,5.5_En.book Page 96 Wednesday, July 28, 2004 9:07 AM Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 En I0407-1 SN 29343827 (C) Copyright 2004 ONKYO CORPORATION Japan. All rights reserved.
