Instructions / Assembly

Manufactured by Benjamin Moore & Co. 101 Paragon Drive, Montvale, NJ 07645 Tel: [phone] Fax: [phone] www.Insl-x.com M72 RP-27XX EN 051815
RUBBER BASED POOL
PAINT SATIN FINISH
RP-27XX
Features
General Description
• Durable Low Sheen
Finish
• VOC Compliant in all
areas
• Resists Fading, Abrasion,
and Alkalis
A rubber based coating for new or old concrete pools. This product
complies with current volatile emission (VOC) standards outlined by
the Ozone Transport Commission. It provides a durable low sheen
finish for use in residential and commercial pools. Suitable for use in
fresh or salt water and acceptable for use in chlorinated pools. Resists
fading, abrasion and alkalis. See Insl-x
®
Rubber Based Swimming
Pool Paint Application Instructions for complete instructions
regarding application. For repaints, Rubber Based Pool Paint
should only be applied over a Chlorinated Rubber or another
Synthetic Rubber Based Pool Paint.
Recommended For
Limitations
Use for pools or fountains. Rubber Based Pool Paint is designed
for use on concrete, Marcite, and Gunnite surfaces. The integrity
of the Marcite or Gunnite must be sound and solid. Do not
use in hot tubs and spas due to high water temperatures. We
do not recommend painting stainless steel, aluminum,
galvanized, fiberglass, steel or vinyl lined pools with this
product. DO NOT APPLY OVER A PREVIOUS EPOXY OR
ACRYLIC POOL PAINT!
• Best time to paint is when temperatures are between 65°F and
85°F.
• Do not paint if rain or excessive moisture is expected within
4 - 6 hours.
• Do not paint in direct rays of the sun.
• Do not apply this coating over any epoxy based or water based
pool paints.
Product Information
Colors — Standard: Light Reflectance Values
RP2710 – White 85% plus
RP2719 – Aquamarine X
RP2720 – Black X
RP2723 – Ocean Blue 81%
RP2724 – Royal Blue 57%
Can be tinted with up to 2 oz. per gallon of Industrial (844 type) colorant.
Technical Data◊
White
Vehicle Type
Synthetic Rubber
Pigment Type
Titanium Dioxide
Volume Solids
59 ± 1.0%
Coverage per Gallon at
Recommended Film Thickness
400 – 500 Sq. Ft.
Recommended Film
Thickness
– Wet
3.2 - 4.0 mils
– Dry
1.9 - 2.4 mils
Depending on surface texture and porosity. Be sure to
estimate the right amount of paint for the job. This will
ensure color uniformity and minimize the disposal of excess
paint.
Dry Time @ 77°F
(25°C) @ 50% RH
– Tack Free
30 Minutes
– To Recoat 12 –24 H
ours
– Full Cure
7 days outdoors
10 - 14 days indoors
High humidity and cool temperatures will result in longer dry,
recoat and service times.
Dries By
Evaporation
Viscosity
85 – 95
KU
Flash Point
80°F or greater
(TT-P-141, Method 4293)
Gloss / S
heen Satin [5 -
10@60°]
Surface Temperature at
Application
– Min. 40
°F
– Max. 90
°F
Thin With
Do Not Thin
Clean Up
Xylene
Weight Per Gallon
12.9
lbs.
Storage Temperature
– Min. 45
°F
– Max. 95
°F
Volatile Organic Compounds (VOC)
338 Grams/Liter 2.82 Lbs./Gallon
— Tint Bases:
N/A
— Special Colors:
Contact your dealer.
Certification:
The products supported by this data sheet contain a maximum of 340
grams per liter VOC/VOS (2.83 lbs/gal.) excluding water and exempt
solvents.
This product is compliant under the Ozone Transport Commission
regulations as a Swimming Pool Paint.
Pool paint applications are not addressed by LEED (Leadership in Energy
and Environmental Design).
Technical Assistance:
Available through your local authorized independent Insl-x dealer. For the
location of the dealer nearest you, call 1-800-225-5554 or visit
www.insl-
x.com .
◊ Reported values are for White. Contact dealer for values of
other bases or colors.