FOODSERVICE DISPOSER Installation Manual WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or seious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices related to physical injury Please be certain that the person who installs or uses this appliance carefully reads and understands the Safety Instructions contained in this manual. www.insinkerator.
Table of Contents Introduction Introduction ..................................................................................... 4 Clean the Drain Line ........................................................................ 4 Typical Installation ........................................................................... 4 Required Tools/Materials ................................................................. 4 Instructions Pertaining to Risk of Fire, Electrical Shock, or Injury to Persons.............
Read all warnings before proceeding. Introduction INTRODUCTION TYPICAL INSTALLATION The InSinkErator Foodservice food waste disposer is UL® and cUL® Listed when installed in conjunction with InSinkErator mounting adaptors and controls (see Figure 1 for typical installation).
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS NOTICE PROPERTY DAMAGE PERSONAL INJURY/PROPERTY DAMAGE If the electrical installer is not experienced in electrical installation, we recommend seeking competent professional assistance. Disposer or accessory damage due to improper installation is not covered under warranty. All installations must comply with local electrical codes.
Installing the Disposer NOTICE WARNING PROPERTY DAMAGE To avoid excess vibration, InSinkErator recommends a minimum countertop thickness of 16 gage stainless steel. PERSONAL INJURY • For safe operation, install the disposer in compliance with the minimum distance illustrated in Figure 2. • Disposer must be properly installed to prevent serious injury from moving shredder part. DISPOSER MOUNTING 6-1/2" (165.10 mm) 6-5/8" (168.28 mm) 6-5/8" (168.28 mm) 2-3/4" (69.85 mm) 3-3/8" (85.73 mm) 7-3/4" (196.
Standard InSinkErator Mountings #5 MOUNTING ASSEMBLY Follow these instructions to install a #5 sink flange to a standard 3-1/2 to 4 inch sink opening. (1) Stopper 1. Unscrew the three backup screws (6) until they are flush with the upper mounting flange (5) surface. Pry the retainer ring (7) free from the strainer flange (2) with a screwdriver and separate all mounting assembly parts (2-7). (2) Strainer Flange 2.
Standard InSinkErator Mountings #6, #7, & SINK BOWL MOUNTING ASSEMBLIES 1. Place the mounting flange (1) over the existing collar adaptor connection lip or sink bowl flange (this may require some force). 4. From the bottom, insert two screws through opposite sides of the flat gasket (3) and mounting flange, into the threaded fasteners in the existing flange. The flat gasket is used only in the #6 mounting assembly. The screws should protrude about 1/4 inch below the mounting gasket. 2.
Plumbing Connections Install the flow control valve, water solenoid valve, and the syphon breaker according to the direction of the flow arrows marked on each valve body (see Figure 9). NOTICE PROPERTY DAMAGE These plumbing instructions were written for an experienced competent installer. If the installer is not experienced in plumbing installation, InSinkErator recommends that competent professional assistance is sought.
Standard Motor Connection Wiring Diagrams NOTE: The diagrams below show standard motor connection wiring for a manual switch operation. For alternate controls, please refer to the control panel installation manual. 4 5 6 2 MOTOR LEAD WIRE# 1 2 3 L2 10 5 11 6 7 1 7 L1 L2 L1 L1 7 2 L2 8 3 6 Figure 11. Incoming 208-230V Single Phase Line Power 12 4 MOTOR LEAD WIRE# 1 5 4 MOTOR LEAD WIRE# Figure 10.
Electrical Connections ELECTRICAL CONNECTIONS WARNING To connect the disposer to the electricity: ELECTRICAL SHOCK • Turn off the electrical supply to the disposer before servicing. Test the circuit with a voltmeter or circuit tester to ensure the power is off. 1. Remove the screw in the center of the disposer terminal box. • Installation must conform to all local electrical codes. 3. Connect an electrical conduit connector to the hole in the bottom of the exposed wiring compartment. 2.
Operating Instructions OPERATING THE DISPOSER 1. Make sure there are no foreign objects in the disposer grind chamber. Do not pre-load the disposer with food waste prior to starting. 2. Push the start button on the control switch. The disposer will run and water will flow into the disposer. 3. Feed food waste into the disposer in a steady, continuous flow. 4. When all food waste is flushed away, push the stop button on the control switch.
Troubleshooting WARNING ELECTRICAL SHOCK Disconnect power before servicing. Troubleshooting for problems other than what is listed below should be performed by a qualified service person. Troubleshooting performed by untrained personnel could result in electrical shock or damage to the disposer. Disconnect power before servicing. PROBLEM POSSIBLE CAUSE SOLUTION Disposer will not start and water does not flow. • No incoming water. • Turn on electrical supply. Disposer will not start but water flows.
Notes 14
Food Waste Disposers Limited Warranty InSinkErator®, a division of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or “we” or “our” or “us”) warrants to the original purchaser only (“Customer” or “you” or “your”), subject to the exclusions below, that your InSinkErator® (the “InSinkErator Product”) will be free from defects in material and workmanship for one year from the original date of purchase (the “Warranty Period”).
