Installation Sheet

ManualsBrandsInSinkErator ManualsGarbage DisposersFWD-1 Garbage Disposal, 1/3 HP

Slotted Screwdriver, Adjustable Pliers, Plumber’s Putty, Electrical

Tape

Phillips Screwdriver, Drain Auger, 3/8" Electrical Clamp Connec-

tor, Wire Nuts (2), Second 1 1/2" Drain Trap, Hammer, Hacksaw,

Water Hose Clamp, Pipe Wrench, Copper Ground Wire, Dish-

washer Drain Connection Kit, Air Gap, Electrical On/Off Switch,

Drain Tube Extension, 1/4” Allen Wrench

Mounting Assembly

A: Stopper

B: Sink Flange

C: Fiber Gasket

D: Backup Ring

E: Mounting Ring

F: Screws (3)

G: Snap Ring

Disposer

I: Lower Mounting Ring

J: Dishwasher Inlet

K: Discharge Outlet

Installation, Care & Use Manual

SAFETY SYMBOLS

Read through the entire Installation, Care &

Use manual before installing the disposer.

Determine which of the tools, materials, and

accessories you will need before you begin.

Make sure you have all necessary disposer

parts before installing the disposer (see part

TOOLS AND MATERIALS YOU WILL NEED:

TOOLS, MATERIALS, AND ACCESSORIES

YOU MAY NEED:

FOOD WASTE

DISPOSER

(1/3 HP Model FWD-1 & 1/2 HP Model FWD-2)

Warning indicates

a potentially hazardous situation

which, if not avoided, could result in

death or serious injury.

Caution indicates a

potentially hazardous situation which,

if not avoided, may result in minor or

moderate injury.

Discharge

L: Bolts (2)

M:Discharge Tube (1-1/2" Diam.)

N: Flange

O: Gasket

Part No. 76051 - Rev. A

Summary of content (6 pages)

PAGE 1
Part No. 76051 - Rev. A FOOD WASTE DISPOSER (1/3 HP Model FWD-1 & 1/2 HP Model FWD-2) Installation, Care & Use Manual TOOLS AND MATERIALS YOU WILL NEED: Read through the entire Installation, Care & Use manual before installing the disposer. Determine which of the tools, materials, and accessories you will need before you begin.
PAGE 2
INSTALLATION INSTRUCTIONS 1 CHECK INSTALLATION DIMENSIONS A: Disposer Height B: Distance from bottom of sink bowl to centerline of discharge outlet. (Add 1/2" when stainless steel sink is used.) C: Distance from centerline of the discharge outlet to end of discharge tube. D: Disposer Width E: Distance from disposer vertical centerline to centerline of P-trap connection. F: Centerline of disposer discharge to centerline at waste pipe entering wall.
PAGE 3
6 REMOVE EXISTING DISPOSER 1. Turn off electrical power at fuse box or circuit breaker. Electric Shock s Turn off electrical power at fuse s Disposer must be grounded. box or circuit breaker before Improper connection can removing electrical cover plate. result in electric shock. Personal Injury s Do not position your head or body under disposer; unit could fall during removal or installation. 2. Disconnect drain trap from disposer waste discharge tube with adjustable pliers (see Fig. 6-1).
PAGE 4
9 CONNECT DISPOSER TO ELECTRICAL SUPPLY Electric s Improper connection of the equipmentgrounding conductor can result in a risk of cian or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the cian. s This disposer must be properly grounded. s Do not attach ground wire to gas supply pipe. Shock s Disconnect power before installing or servicing disposer.
PAGE 5
10 CONNECT DISPOSER TO MOUNTING ASSEMBLY Clear any objects from inside the disposer grind chamber before mounting the disposer. Personal Injury: Do not position your head or body under disposer; unit could fall during installation. 1. Position disposer with three mounting tabs (A) aligned in position to slide over mounting tracks (B) (see Figure 10-1). 2.
PAGE 6
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS (SAVE THESE INSTRUCTIONS) When using electric appliances, basic precautions are always to be followed, including: s This product is designed to dispose of normal household s Read all instructions before using the appliance.