Installation Care and Use Manual

Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
a
Select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
The tank should be within 16" or less
of faucet water lines and within 30"
or less of a standard grounded outlet.
While holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Property Damage: Tank must be located
within 16" of faucet and within 30" or less
of a standard grounded outlet. DO NOT
extend plumbing or electrical lines.
3
Tank must be
mounted level
to ensure
proper operation.
Mount tank vertically in an area that allows clear-
ance on the underside of the tank for drainage, if
necessary.
DO NOT over tighten screws.
Pre-drill 1/8" pilot holes at marks.
Turn screws into pre-drilled holes,
leaving 1/4" exposed.
Hang the tank on the screws.
Tighten the screws with only
1/2 turn clockwise.
b
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
Leave 1/4" for
hanging tank.
Without depressing the gray button,
place the snap-connect fitting at
the end of the blue or copper 1/4"
tube onto the left fitting on the tank,
pushing until it clicks into place. (1)
Slip the flexible white 7/16" tube
over barbed steel fitting and slide
down approximately 1/2". (2)
Slip the clear 5/16" tube over the
smooth plastic fitting and slide down
approximately 1/2". (3)
Check for pinched or crimped tubes.
4
a
Property Damage: Pinched or blocked water lines
may cause damage to the dispenser tank. Check
to make sure tubes are connected properly and
are pushed down as far as possible.
Hose clamps are not needed for any
of the connections.
(1) (2) (3)
MOUNTING THE TANK
CONNECTING FAUCET TO TANK
Property Damage: Do not pinch or break tubing.
Do not distort the last 1 inch of tubing.
From under the sink, place the
semi-circular mounting plate onto
the threaded stud.
Place hex nut onto the threaded
stud. Ensure dispenser handle is on
preferred side and that faucet head
is at desired angle.
Insert screwdriver into hole on side
of hex tool (creating a “T”), and use
tool to tighten nut and secure faucet.
2
Semi-circular mounting plate should
encircle all descending tubes and
extend beyond sink hole when tight.
Insert rubber O-ring into groove on
brass seat.
Place brass seat, O-ring side down,
over hole in sink or countertop.
Holding brass seat in place, feed
tubes down through the hole in sink
or countertop until base touches
brass seat.
Rotate brass seat until the two
retaining studs fit into the holes on
the faucet base and base sits firmly
on brass seat.
Unpack dispenser components.
The recommended installation for
this faucet is dispenser handle on
the right.
The unique design allows the
handle to be fully functional when
placed to the right or left of faucet.
Determine preferred handle
placement before installing.
To ease feeding of tubes through hole, first
insert blue tube with quick-connect attachment
and then insert the remaining tubes.
b
a
c
d
Wetting O-ring with water prior to
inserting into brass seat helps hold
ring in place during installation.
INSTALLING THE FAUCET - 3300
8 9