Installation Care and Use Manual

Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
From under the sink, place the
semi-circular mounting plate onto
the threaded stud.
Place hex nut onto the threaded stud.
Ensure faucet head is at desired angle.
Insert screwdriver into hole on side of
hex tool (creating a “T”), and use tool
to tighten nut and secure faucet.
2
Semi-circular mounting plate should
encircle all descending tubes and
extend beyond sink hole when tight.
Ensure that the black O-ring is
properly seated in the base of the
dispenser head (the groove on the
underside of the dispenser).
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Feed tubes down through the hole
in the sink or countertop until the
base is at rest on the sink or
countertop surface.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Unpack dispenser components.
On a firm, flat surface, carefully
straighten the copper tubing.
To ease feeding of tubes through hole,
first insert blue tube with quick-connect
attachment and then insert the remaining tubes.
b
a
c
d
Make sure to use rubber O-ring
to ensure proper seal.
INSTALLING THE FAUCET - 1100/2200
The wall outlet for your dispenser must have power supplied to it continuously
and must be fused. It should not be controlled by the same wall switch
that operates your disposer, unless using an InSinkErator SinkTop Switch
TM
.
PREPARATION
START HERE
PROPER INSTALLATION SHOULD TAKE ABOUT 2-4 HOURS
Identify locations for the dispenser
faucet, tank and filter.
Check to make sure there is proper
clearance for dispenser handles to
be fully opened.
Check to make sure counter is 3"
thick or less.
Make sure there is a grounded
electrical outlet under the sink.
Turn off water supply.
If using the sink sprayer hose hole,
remove nut that connects sprayer
hose at bottom of faucet.
Using adjustable wrench, remove nut
connecting sprayer washer flange in
sprayer hole.
Plug hose opening with either a 1/8"
plug or a 1/4" cap (not supplied).
1
a
b
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
If you have to drill through sink or
countertop, you may need to rent or purchase
the appropriate tools.
Consult a professional before drilling into
a surface other than stainless steel.
c
What if you don’t have a sprayer hole or
don’t want to use it?
Many homeowners replace the soap
dispenser in their sink with an instant
hot water dispenser.
If drilling a hole into a stainless steel
sink or counter top, you can cut a
mounting hole for the dispenser with a
hole saw for stainless steel, or you can
use a hole punch.
Required Hole Size
F-HC1100 ................2
5
⁄8"
F-GN1100 ................3
1
⁄4"
F-HC2200 ................2
7
⁄8"
F-GN2200 ................3
1
⁄2"
F-HC2215 ................2
7
⁄8"
F-GN2215 ................3
1
⁄2"
F-HC3300 ................2
1
⁄2"
F-H3300 ...................2
1
⁄2"
Required minimum from
center of hole to wall
Maximum counter thickness is 3".
F-HC1100 ................1
3
⁄8" - 1
1
⁄2"
F-GN1100 ................1
1
⁄4" - 1
1
⁄2"
F-HC2200 ................1
3
⁄8" - 1
1
⁄2"
F-GN2200 ................1
1
⁄4" - 1
1
⁄2"
F-HC2215 ................1
3
⁄8" - 1
1
⁄2"
F-GN2215 ................1
1
⁄4" - 1
1
⁄2"
F-HC3300 ................1
3
⁄8" - 1
1
⁄2"
F-H3300 ...................1
3
⁄8" - 1
1
⁄2"
6 7
An assistant may be needed to
hold the dispenser head in place while
securing the dispenser.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube