Use and Care Manual

Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
a
n Select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
The tank should be within 16" or less
of dispenser and within 30" or less of
a standard grounded outlet.
n While holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Property Damage: Tank must be located
within 16" of dispenser and within 30" or less
of a standard grounded outlet. DO NOT
extend plumbing or electrical lines.
3
Tank must be
mounted level
to ensure
proper operation.
Mount tank vertically in an area that allows clear-
ance on the underside of the tank for drainage, if
necessary.
DO NOT over tighten screws.
n Pre-drill 1/8" pilot holes at marks.
n Turn screws into pre-drilled holes,
leaving 1/4" exposed.
n Hang the tank on the screws.
n Tighten the screws with only
1/2 turn clockwise.
b
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
Leave 1/4" for
hanging tank.
n Without depressing the gray button,
place the snap-connect fitting at
the end of the blue tube onto the
left fitting on the tank, pushing until it
clicks into place. (1)
n Slip the flexible white 7/16" tube
over barbed steel fitting and slide
down approximately 1/2". (2)
n Slip the clear 5/16" tube over the
smooth plastic fitting and slide down
approximately 1/2". (3)
n Check for pinched or crimped tubes.
4
a
Property Damage: Pinched or blocked water lines
may cause damage to the dispenser tank. Check
to make sure tubes are connected properly and are
pushed down as far as possible.
Hose clamps are not needed for any
of the connections.
MOUNTING THE TANK
CONNECTING DISPENSER TO TANK
Property Damage: Do not pinch or break tubing. Do
not distort the last 1 inch of tubing.
n From under the sink, place
the mounting plate onto
the threaded stud.
n Place hex nut onto the threaded
stud. Ensure handle is on preferred
side and that dispenser head is at
desired angle.
n Insert screwdriver into hole on side of
hex tool (creating a “T”), and use tool
to tighten nut and secure dispenser.
2
Mounting plate should encircle all
descending tubes and extend beyond
sink hole when tight.
n Insert rubber O-ring into groove on
brass seat.
n Place brass seat, O-ring side down,
over hole in sink or countertop.
n Holding brass seat in place, feed
tubes down through the hole in sink
or countertop until base touches
brass seat.
n Rotate brass seat until the two
retaining studs fit into the holes
on the dispenser base and base sits
firmly on brass seat.
n Unpack components.
n The recommended installation
for this dispenser is the handle on
the right.
The unique design allows the
handle to be fully functional when
placed to the right or left of faucet.
Determine preferred handle
placement before installing.
To ease feeding of tubes through hole, first
insert blue tube with quick-connect attachment
and then insert the remaining tubes.
b
a
c
d
Wetting O-ring with water prior to
inserting into brass seat helps hold
ring in place during installation.
INSTALLING THE DISPENSER - 3300
8 9
(1) (2) (3)
Do not plug in the hot water tank Until Step 6C.
NOTICE
NOTICE
NOTICE
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube