Use and Care Manual

FILTRATION INFORMATION
Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system.
To reduce the risk associated with property damage due to water leakage or flooding:
• Read and follow Use Instructions provided with the original system before installation
and use of this product.
To reduce the risk of water leakage or flooding, and to ensure optimal filter performance:
• Change the disposable filter cartridge every six months or sooner if you
observe a noticeable reduction in water flow rate.
• Failure to replace the disposable filter cartridge at recommended intervals may
lead to reduced filter performance and cracks in the filter housing, causing
water leakage or flooding.
• For systems using two handle HC model dispensers, operate only one handle
at a time.
• For questions or concerns, please contact Customer Service at
1-800-558-5700.
The InSinkErator Instant Hot Water Filtration System offers two levels of filtration,
depending on the filter used: F-1000S is intended for use in filtering particulates,
chlorine taste and odor from drinking water, and has not been evaluated for other
uses; F-2000S reduces particulates, chlorine taste and odor, plus cysts, lead, mercury,
asbestos, benzene, atrazine, 2,4-D, Lindane, Carbofuran and p-Dichlorobenzene. The
system is typically installed (near or beneath a sink) where filtered drinking water is
desired, and must be installed, operated and maintained as specified in the installation
and use instructions.
16
WHAT TO DO
Water and steam spits
forcefully from spout
without turning on the
dispenser.
Continuous boiling
sounds in the tank.
Water is not hot.
• Unit is boiling.
May be normal during initial setup.
• The unit is unplugged.
• The electric outlet is inoperative.
• Activate dispenser lever to release some water from
the tank.
• Adjust water temperature using dial or touch screen
on tank front.
Remember that at higher altitudes, water boils
at lower temperatures.
• Make sure the unit is connected to a properly grounded
electric outlet.
• Make sure the circuit breaker or fuses are
functioning properly.
• Check that the outlet is not switched off.
Water is too hot
or not hot enough.
• Thermostat is not adjusted to
your needs.
•
Adjust the thermostat slowly, then activate dispenser lever for 20
seconds to bring in fresh water to be heated at the new setting.
Allow 5-7 minutes for water to reach new temperature.
Water comes out the
vent instead of spout.
• Outlet tube is blocked. • Check that outlet tube is not kinked, twisted or pinched.
• Unscrew spout end piece and clean out any debris.
Water is dripping from
the spout/vent
intermittently.
• The expansion chamber isn’t draining
properly due to low water pressure.
• The spout is blocked.
• Unplug the unit. If the dripping doesn’t stop after a few
minutes, check the supply valve to ensure that is fully
open and there are no obstructions in the water line
reducing the pressure below 30 psi (i.e., a poorly mounted
saddle valve, a clogged water filter, or a partially opened
shut-off valve).
• Unscrew spout end piece and clean out any debris.
Water is dripping
from the spout/vent
constantly.
• Debris in the water line may be
in the dispenser valve seat causing a
slow water leak.
• Unscrew spout end piece and clean out any debris.
• Activate lever 7-10 times to flush dispenser & lines.
Divided stream.
• Debris in the end piece. • Unscrew spout end piece and clean out any debris.
PROBLEM POSSIBLE CAUSE
FILTRATION ISSUES
Water taste or odor. • Filter needs to be flushed out.
• Life of filter has expired.
• Activate the dispenser lever and run until the water is
cold. If there is no change, replace filter cartridge.
Please read Troubleshooting Guide and/or visit
www.insinkerator.com before calling customer service
Water discoloration/rusty
appearance.
• Corrosion of unit. • Unplug and drain unit as described in the Seasonal
Storage/Drainage Section on page 15 of this manual.
If the water discoloration remains after draining and
refilling unit, discontinue use and contact an autho-
rized InSinkErator service agent.
New filter leaks or
doesn’t fit.
No water flow or
low water flow.
• Head and bracket not fully rotated.
• Filter O-ring breach.
• Life of filter has expired.
• Remove, inspect, reinstall filter cartridge.
• Remove new filter, replace with old filter. Check operation.
If OK, reinstall new filter and recheck operation.
• Replace filter cartridge. See page 15.
TROUBLESHOOTING
17
NOTICE
F-1000 Cartridge (included with this system) Chemical & Mechanical Reduction Filter Specifications:
This cartridge pr
ovides mechanical and chemical reduction of chlorine taste & odor and particulate class III.
Filter Capacity:
500 gallons, depending on local water conditions. Note that while the testing was performed under
standa
rd laboratory conditions, actual performance may vary. Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection befo
re or after the system. For cold water use only.
Systems must be
installed and operated in accor
dance with the Manufacturer’s recommended procedures and guidelines. See warranty
ca
rd for warranty. For service and parts, contact your local dealer or InSinkErator
®
directly at 1-800-558-5700.
A
pplication guidelines/Water Supply Parameters for NSF Testing: Service flow of 0.75 gpm, community or
private well water suppl
y, water pressure of 20-120 psi (138-827 kPa), water temperature of 33˚F–100˚
Nominal
Particulate Class III,
≥5 µm to <15 µm
270,000 pts/mL
2.1 mg/L 2.0 mg/L ± 10%
At least 10,000
particles/mL
82 pts/mL 99.9% ≥85%
0.06 mg/L 97.0% ≥ 50% J-00082587
J-00119308
F Except as
noted, all testing performed at pH = 7.5
± 0.5, Flow: 0.75 gpm, Pressure: 60 psi, Temp: 20˚± 3˚C.
Contact an authorized InSinkErator service agent for r
epairs or replacement components. Replacement filters
F-1000 and F-2000 can be or
dered by calling 800-558-5700, visiting shop.insinkerator.com, or by contacting
an authorized InSinkErator r
eseller.
Refer to the Performance Data Sheet for InSinkErator Filter System Model F-2000S
Replacement Cartridge: F-2000
Pressure: 30-120 (207-827 kPa) psi
Temperature: 33
º
F - 100
º
F
Flow Rate: 0.75 gpm
Capacity: 500 gallons
Tested & Certified by NSF International against NSF/ANSI Standard 42 in the following
InSinkErator Systems Only: GN1100, HC1100, GN2200, HC2200, GN2215, HC2215,
H3300 or HC3300 for the reduction of claims specified on the Performance Data Sheet.
For systems using two handle HC model dispensers, operate only one handle at a time.