Installation Sheet

ManualsBrandsInSinkErator ManualsKitchen FaucetsModern Hot and Cold Water Dispensers

:03

AVISO:

Daños materiales. No utilice un prolongador con el dispensador

de agua caliente instantáneo. (Es necesario que haya un tomacorriente

estándar con conexión a tierra dentro de los 760 mm (30") del

dispensador de agua caliente instantáneo debajo del fregadero).

NOTICE:

Property Damage. Do not use an extension lead with the

instant hot water dispenser. (A standard earthed outlet within 30"

(760 mm) of the instant hot water dispenser is required under the sink.)

AVIS :

dommages matériels. N’utilisez pas une rallonge avec le

distributeur d’eau chaude instantanée. (Une prise standard mise à la

terre se trouvant à une distance de 30 po (760 mm) du distributeur

d’eau chaude instantanée est requise sous l’évier.)

PRECAUCIÓN: Riesgo de escaldaduras (quemaduras). El dispensador de agua

caliente instantáneo ofrece agua casi hirviendo (de hasta 210 ºF/98 ºC) que puede

causar instantáneamente escaldaduras o quemaduras. Tenga especial cuidado cuando

use esta operación.

AVIS :

dommages matériels. La course des tubes doit épouser les contours

de l’armoire pour laisser de l’espace de rangement sans coude en équerre.

Les tubes doivent avoir des coupes propres, perpendiculaires, sans barbure

pour obtenir un ajustement parfait.

AVISO:

Daños materiales. No extienda las líneas más allá de los

400 mm (16") establecidos. Cerciórese de que los tubos y el conector en

“Y” estén bien ajustados.

AVIS :

dommages matériels. Ne prolongez pas les conduites au-delà

des 16 po (400 mm) fournis. Assurez-vous que le(s) tube(s) et le

connecteur Y soient bien assemblés.

NOTICE

: Property Damage. Do not extend the lines farther than the

16" (400 mm) provided. Ensure tube(s) and “Y” connector t securely.

NOTICE:

Property Damage. Tube runs need to form to the cabinet’s

contours to allow storage space with no sharp bends. Tubes need clean,

perpendicular, burr-free cuts to ensure a true t.

AVISO:

Daños materiales. Los tramos de tubo deben formar el contorno

del gabinete para dejar espacio de almacenaje sin curvas agudas. Los tubos

necesitan cortes limpios, perpendiculares y sin rebabas, para asegurar un

ajuste adecuado.

14A

CAUTION: Scalding Hazard. The instant hot water dispenser delivers near-

boiling (up to 210ºF/98ºC) water which can instantly cause scalds or burns. Use

care when operating this appliance.

Allow 12-15 minutes for water to reach target temperature. Gurgling or hissing is

normal during the initial heating cycle.

Deje transcurrir 12 a 15 minutos para que el agua alcance la temperatura deseada. Es normal

que se oigan ruidos sibilantes o de borboteo durante el ciclo de calentamiento inicial.

Allouez de 12 à 15 minutes pour que l’eau atteigne la température désirée. les

gargouillements ou les sifements sont normaux durant le cycle de chauffage initial.

MISE EN GARDE : danger de brûlure. Le distributeur d’eau chaude instantanée

fournit de l’eau presque bouillante (jusqu’à 210 °F/98 °C) qui peut causer des

échaudages ou des brûlures. Faites attention lorsque vous utilisez cet appareil.

Remarque : vériez toutes les connexions pour vous assurer qu’elles sont

bien serrées et qu’il n’y a pas de fuite. Laissez l’eau couler pendant quatre

minutes pour rincer les conduites et remplir le réservoir.

Nota: Verique que todas las conexiones estén ajustadas y que no haya

fugas. Deje correr el agua durante 4 minutos para limpiar las líneas y llenar

el depósito.

210

Note: Check all connections to ensure they are tight and that there are

no leaks. Allow water to run for 4 minutes to ush lines and ll tank.

210˚F / 98˚C

—

13A

13B

ENGLISH

5-YEAR IN-HOME FULL SERVICE LIMITED WARRANTY

INSTANT HOT WATER DISPENSER TROUBLESHOOTING

CLEANING THE INSTANT HOT WATER DISPENSER

CAUTION: PERSONAL INJURY

NOTICE

• Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.

• A drainage pan, plumbed to an appropriate drain or outtted with a leak detector, should be used in those applications

where any leakage could cause property damage.

• Use only mild cleaners to clean the instant hot water dispenser and plastic components.

• To clean out end piece, unscrew spout end piece and clean out any debris. For FHC1020 and FH1020, insert end piece

removal tool to unthread end piece from spout. Reference components diagram part "L."

• Cleaners with acids, abrasives, alkaline or organic solvents will result in deterioration of the plastic components and void

the warranty.

• Regularly check for signs of corrosion by examining the appearance of the dispensed water.

• If the water discoloration remains after draining and relling the unit, discontinue use and contact

an authorized InSinkErator service agent.

CARE AND USE

CAUTION: Electric Shock Hazard. To prevent electrical shock, disconnect power before servicing unit. Use only a

properly earthed and polarized electric outlet.

This limited warranty is provided by InSinkErator, a business unit of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or

“we” or “our” or “us”) to the original consumer owner of the InSinkErator product with which this limited warranty is provided

(the “InSinkErator Product”), and any subsequent owner of the residence in which the InSinkErator Product was originally

installed (“Customer” or “you” or “your”).

InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject

to the exclusions described below, for the “Warranty Period”, commencing on the later of: (a) the date your InSinkErator Product

is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial

number. You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation

supporting either (a) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute

discretion, based upon your InSinkErator Product serial number.

Permitted Uses

You may use your InSinkErator Product hot/cold water tank and filter system in combination with any genuine InSinkErator

Product instant hot water dispensers and component parts and/or Authorized OEM Products. “Authorized OEM Products” mean

those hot, cold or hot/cold water dispensers and component parts that have been manufactured by an authorized InSinkErator

original equipment manufacturer (“Authorized OEM”) and which have documentation expressly stating that such Authorized OEM

Products are compatible with the InSinkErator Product(s). Authorized OEMs may change from time to time. A list of Authorized

OEMs is available to you upon request or at: www.insinkerator.com/oem. Use of your InSinkErator Product in combination with any

products other than Authorized OEM Products will void this warranty.

What is Covered

This limited warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products

used by a consumer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE INSINKERATOR

PRODUCT, PROVIDED THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY IS PRACTICABLE, WE

MAY PROVIDE YOU A REFUND OF YOUR PURCHASE PRICE OR A CREDIT TOWARDS ANOTHER INSINKERATOR PRODUCT.

What is not Covered

This limited warranty does not extend to and expressly excludes:

• Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the Manufacturer’s

control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s),

failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or

local electrical and plumbing codes.

• Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust, scratches, dents

or comparable and reasonably expected losses or damages.

• Losses or damages caused by any product or component part used with the InSinkErator Products, including both Authorized

OEM Products and other products and components.

In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or

industrial application.

No Other Express Warranty Applies

This limited warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty,

written or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any

other warranty on behalf of Manufacturer. The terms of this limited warranty shall not be modified by the Manufacturer, the

original owner, or their respective successors or assigns.

What we will do to Correct Problems

If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions concerning

your InSinkErator Product or how to determine when service is needed, please call the toll free InSinkErator AnswerLine® at

1 (800) 558-5700, or visit our website at www.insinkerator.com. You may also notify us at: InSinkErator Service Center,

1250 International Drive, Mount Pleasant, WI 53177 USA.

The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator

Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your

installation receipt, or (b) the date shown on your purchase receipt.

Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator

Product is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service

Center. Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only

an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty

claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator

service representative.

If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either

repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair

or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined

by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be

provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired,

the warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original

Warranty Period.

This instant hot water dispenser is covered by Manufacturer’s limited warranty. This limited warranty is void if you attempt to

repair the InSinkErator Product. For service information, please visit www.insinkerator.com or call, toll free, 1-800-558-5700.

Limitation of Liability

TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE REPRESENTATIVES

BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS,

WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE INSINKERATOR PRODUCT OR THE

MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER SHALL NOT BE LIABLE FOR

DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF

ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL

MANUFACTURER’S LIABILITY TO YOU EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.

The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use

or revenue, cost of capital or loss or damage to property or equipment.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply

to you. This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state.

8 9

Not included

No incluidos

Non compris

PROBLEM POSSIBLE CAUSE WHAT TO DO

Water and steam spits

forcefully from spout

without turning on

the instant hot water

dispenser.

• Unit is boiling.

May be normal during initial

set-up.

• Activate instant hot water dispenser to release some water from

the tank.

• Adjust water temperature using dial on tank front.

• Remember that at higher altitudes, water boils at

lower temperatures.

Water is not hot. • The unit is unplugged.

• The electric outlet is

inoperative.

• Make sure the unit is connected to a correctly

earthed electric outlet.

• Make sure the circuit breaker or fuses are

functioning correctly.

• Check that the outlet is not switched off.

Water is too hot or

not hot enough.

• Thermostat is not

adjusted to your needs.

• Adjust the thermostat slowly, then activate instant hot water

dispenser for 20 seconds to bring in fresh water to be heated

at the new setting. Allow 5-7 minutes for water to reach new

temperature.

Water comes out of

the vent instead of

spout.

• Outlet tube is blocked. • Check that outlet tube is not kinked, twisted or pinched.

• Unscrew spout end piece and clean out any debris. For FHC1020 and

FH1020, insert end piece removal tool to unthread end piece from spout.

Reference components diagram part "L."

Water is dripping

from the spout/vent

intermittently.

• The expansion chamber is

not draining properly due

to low water pressure.

• The spout is blocked.

• Unplug the unit. If the dripping does not stop after a few minutes,

check the supply valve to ensure that is fully open and there are

no obstructions in the water line reducing the pressure below

30 psi.

• Unscrew spout end piece and clean out any debris. For FHC1020 and

FH1020, insert end piece removal tool to unthread end piece from spout.

Reference components diagram part "L."

Water is dripping

from the spout/vent

constantly.

• Debris in the water line

may be in the instant hot

water dispenser valve

seat, causing a slow

water leak.

• Unscrew spout end piece and clean out any debris. For FHC1020 and

FH1020, insert end piece removal tool to unthread end piece from spout.

Reference components diagram part "L."

• Activate instant hot water dispenser 7-10 times to ush dispenser

and lines.

Water discoloration/

rusty appearance.

• Corrosion of unit. • Unplug and drain unit as described in the Seasonal Storage/

Drainage Section of the Installation, Care & Use manual packaged

with your hot water tank. If the water discoloration remains after

draining and relling the unit, discontinue use and contact an

authorized InSinkErator service agent.

Divided stream. • Debris in the end piece.

• Plastic piece

may be installed

upside down.

• Unscrew spout end piece and clean out any debris. For FHC1020 and

FH1020, insert end piece removal tool to unthread end piece from spout.

Reference components diagram part "L."

• Small end of plastic piece faces down.

Note: If needed, extra tubing and Y Connect provided with tank.

Nota: En caso de ser necesario, se incluye con el tanque una tubería

y un conector en Y adicionales.

Remarque : Si nécessaire, un tube supplémentaire et un connecteur en

Y sont fournis avec le réservoir.

HOT ONLY

HOT/COLD

SOLO CALIENTE

CALIENTE/FRÍO

CHAUD SEUL

CHAUD ET FROID

WITH FILTER SYSTEM

WITHOUT FILTER SYSTEM

CON SISTEMA DE FILTRO

SIN SISTEMA DE FILTRO

SANS SYSTÈME DE FILTRAGE

From water supply

Desde el suministro de agua

De l’alimentation en eau

To faucet

Hasta el grifo

Vers le robinet

Activate hot handle

Abra la llave de agua caliente

Actionnez le levier d’eau

chaude.

14B

Turn power on

Encienda la energía

Mettez l’alimentation

électrique sous tension.