ASSEMBLY GUIDE Dual Screen Desktop Mount NS-PMMD22 Before using your new product, please read these instructions to prevent any damage.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NS-PMMD22 Introduction Congratulations on your purchase of a high-quality Insignia product. Your NS-PMMD22 represents the state of the art in monitor mount design and is designed for reliable and trouble-free performance. IMPORTANT SAFETY INSTRUCTIONS 1 Make sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, please contact a professional installer for assistance.
Package contents Parts Make sure that you have all the parts necessary to assemble your new monitor mount: Cable support brackets (pre-installed) # PART QTY. # PART 1 Tube cover 2 4 Support base 1 2 Monitor support arm 1 5 Base clamp 1 3 Monitor support tube 1 6 Anti-slip rubber pads 2 Hardware Make sure that you have all the hardware necessary to assemble your new monitor mount: A M4 x 12 mm (8) B M5 x 12 mm (8) C M6 x 20 mm (3) D M6 x 10 mm (2) E 6.
NS-PMMD22 Installation instructions STEP 1: Preparing your monitors 1 Make sure that your monitors have screw holes on the backs for VESA mounting. You can use monitors with VESA mounting patterns of 75 × 75 mm (3 × 3") or 100 × 100 mm (3.9 × 3.9"). 75 × 75 mm (3 × 3") or 100 × 100 mm (3.9 × 3.9") 75 × 75 mm (3 × 3") or 100 × 100 mm (3.9 × 3.9") 2 Remove the bases or stands from your monitors.
2 Determine which mounting holes to use, based on the thickness of your desk. Insert two M6 x 10 mm screws (D) through the base clamp (5), then tighten the screws using the 4 × 4 Allen wrench (F). Place the anti-slip rubber pads (6) on the tops of the clamp screws. 3 Slide the support base/base clamp assembly over the edge of the desk where you want your monitor mount installed, then tighten both base clamp screws by turning them counterclockwise.
NS-PMMD22 STEP 3: Attaching the monitor support arm Note: The monitor support arm is one piece, so both monitors will be at the same height. As you decide where to position the monitor support arm, remember the tops of the monitors should be level with your eyes. 1 Slide the monitor support arm (2) over the top of the support tube (3). Make sure that the cable support brackets are installed and evenly spaced along the monitor support arm.
STEP 4: Attaching the monitors Note: Monitors can be oriented either horizontally or vertically. Depending on the VESA screw holes on the back of your monitors, you need to use the M4 × 12 mm mounting screws (A) or the M5 × 12 mm mounting screws (B). 1 Determine which mounting screws you need (A or B) by hand-threading a screw into a VESA screw hole. Do not force the screw to fit.
NS-PMMD22 STEP 5: Adjusting the monitors and managing the cables To avoid eye strain: • Position your monitors about an arm’s length from your eyes. • Position your monitors so there is no glare on the screens from windows or light sources. • Tilt the screens up slightly. • If you cannot read the on-screen text when your monitor is positioned correctly, you should increase the text size instead of moving your monitors closer or moving closer to your monitors.
ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
For product inquiries, please contact us with the information below: 1-877-467-4289 www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2022 Best Buy. All rights reserved.
