USER GUIDE L-Shaped Computer Desk NS-ODL3 Before using your new product, please read these instructions to prevent any damage.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L-Shaped Computer Desk Safety information WARNING: Cancer and reproductive harm. www.p65warnings.ca.gov WARNING: Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. • This product is intended to hold maximum weight indicated: • Desktop: Up to 100 lbs. (45.4 kg) • Hutch: Up to 20 lbs. (9.1 kg) • Shelf: Up to 5 lbs. (2.3 kg) • Do not allow children to climb or jump on furniture due to possible accident, injury, or death.
Parts included Note: Parts are labeled on the side of each panel. 1 Top hutch panel 2 Back hutch panel 3 Bottom hutch panel 4 Hutch divider panels (3) 5 Left hutch panel 6 Right hutch panel 7 Main desktop 8 Side desktop 9 Main leg assembly 10 Side leg assembly 14 Side back support bar 4 11 Main back support bar 15 Side front support bar 12 Main front support bar 16 Center leg www.insigniaproducts.
L-Shaped Computer Desk Hardware included LABEL HARDWARE QTY. LABEL HARDWARE QTY. A Wooden dowels 26 H Anchors 2 B Cam-lock screws 19 I M5 × 15 mm bolts 8 Cam locks J 19 M6 × 15 mm bolts 10 C K 3 5 × 50 mm screws 6 D 3.8 × 45 mm screws E M6 × 30 mm bolts 13 L M6 × 50 mm bolts 7 F Washers 13 M Hex wrench 1 Screw covers G 16 Tools needed CAUTION: Do not use a drill to assemble your desk. The drill should only be used to secure your desk to the wall (step 18).
Understanding cam locks and cam-lock screws 6 1 Screw the cam-lock screws (B) into each piece with a Phillips screwdriver. Make sure that they are straight and flush with each panel. 2 Align the cam lock (C) arrow toward to the hole, then insert the cam-lock screw into the hole of the cam lock. 3 Use a Phillips screwdriver to turn the cam lock (C) clockwise until it is locked. The locked position is about a 1/2 turn (160°–185°). Do not overturn the cam lock. www.insigniaproducts.
L-Shaped Computer Desk Assembling your desk STEP 1: Insert wooden dowels into the hutch divider panels You need: 4 Hutch divider panels (3) 1 A Wooden dowels (12) Insert 12 wooden dowels (A) into the edges of the three hutch divider panels (4). Be careful not to insert the dowels into the cam-lock screw holes. Cam-lock screw hole. Do NOT insert dowels here. www.insigniaproducts.
STEP 2: Insert wooden dowels into the bottom hutch panel You need: 3 Bottom hutch panel 1 8 A Wooden dowels (4) Insert four wooden dowels (A) into the edges of the bottom hutch panel (3). www.insigniaproducts.
L-Shaped Computer Desk STEP 3: Connect the hutch divider panels to the bottom hutch panel You need: 4 Hutch divider panels (3) D 3.8 × 45 mm screws (3) G Screw covers (3) Phillips screwdriver 3 Bottom hutch panel 1 Align the wooden dowels on a hutch divider panel (4) with the holes in the bottom hutch panel (3). Make sure that the edges of the panels are flush with each other so the divider panel edge is not raised (as shown). 2 Secure the divider panel with a 3.
STEP 4: Insert wooden dowels into the back hutch panel You need: 2 Back hutch panel 1 10 A Wooden dowels (6) [Insert six wooden dowels (A) into the edges of the back hutch panel (2). www.insigniaproducts.
L-Shaped Computer Desk STEP 5: Connect the back hutch panel to the hutch assembly You need: 2 Back hutch panel Tip: Add a drop of glue (not included) onto the end of each dowel before inserting it into the hole. 1 Align the wooden dowels on the hutch assembly with the holes in the back hutch panel (2). www.insigniaproducts.
STEP 6: Insert wooden dowels and cam-lock screws into the left and right hutch panels You need: 5 Left hutch panel 6 Right hutch panel B Cam-lock screws (8) Phillips screwdriver 1 Insert two wooden dowels (A) into the edges of the left hutch panel (5) and right hutch panel (6). 2 Screw eight cam-lock screws (B) into the left and right hutch panels with a Phillips screwdriver. Make sure that the cam-lock screws are straight and flush with each panel. T 12 A Wooden dowels (2) www.insigniaproducts.
L-Shaped Computer Desk STEP 7: Connect the left and right hutch panels to the hutch assembly You need: Phillips screwdriver 5 Left hutch panel 6 Right hutch panel C Cam locks (8) G Screw covers (4) 1 To connect the left hutch panel (5) to the hutch assembly, align the wooden dowels and cam-lock screws with the holes in the panels. 2 Insert four cam locks (C) into the hutch assembly (as shown). Make sure that the cam lock arrows are pointing toward their corresponding cam-lock screw holes.
STEP 8: Insert cam-lock screws into the top hutch panel You need: 1 Top hutch panel 1 B Cam-lock screws (11) Screw 11 cam-lock screws (B) into the top hutch panel (1) with a Phillips screwdriver. Make sure that the cam-lock screws are straight and flush. T 14 Phillips screwdriver www.insigniaproducts.
L-Shaped Computer Desk STEP 9: Connect the top hutch panel to the hutch assembly You need: Phillips screwdriver 1 Top hutch panel C Cam locks (11) G Screw covers (7) 1 To connect the top hutch panel (1) to the hutch assembly, align the wooden dowels and cam-lock screws with the holes in the panels. 2 Insert 11 cam locks (C) into the hutch assembly (as shown). Make sure that the cam lock arrows are pointing toward their corresponding cam-lock screw holes.
STEP 10: Connect the hutch assembly to the main desktop You need: A Wooden dowels (2) 7 Main desktop 16 K 5 × 50 mm screws (4) Phillips screwdriver 1 Insert two wooden dowels (A) into the bottom edges of the left hutch panel (5) and right hutch panel (6). 2 Align the wooden dowels and screw holes in the hutch assembly with the holes in the main desktop (7). 3 Secure the main desktop with four 5 × 50 mm screws (K) and a Phillips screwdriver. www.insigniaproducts.
L-Shaped Computer Desk STEP 11: Attach support bars to the side leg assembly You need: 10 Side leg assembly 13 Bottom support bar (1) L M6 × 50 mm bolts (2) 15 Side front support bar 14 Side back support bar J M6 × 15 mm bolts (2) M Hex wrench Note: To make assembly easier, do not lock the bolts tightly until you have assembled all other parts. 1 Align the side front support bar (15) with the top/front hole in the side leg assembly (10), then secure with a M6 × 50 mm bolt (L) and a hex wrench (M).
STEP 12: Attach the center leg to the side leg assembly supports You need: 16 Center leg L M6 × 50 mm bolt (1) J M6 × 15 mm bolts (2) 1 Align the bracket on the center leg (16) with the bottom support bar (13), then secure with two M6 × 15 mm bolts (J) and a hex wrench (M). Make sure that the second bracket on the center leg faces the front of your desk (as shown). 2 Align the holes in the center leg (16) and side back support bar (14), then secure with a M6 × 50 mm bolt (L) and hex wrench (M).
L-Shaped Computer Desk STEP 13: Attach support bars to the main leg assembly You need: 9 Main leg assembly 13 Bottom support bar (1) 11 Main back support bar L M6 × 50 mm bolts (2) 12 Main front support bar J M6 × 15 mm bolts (2) M Hex wrench Note: To make assembly easier, do not lock the bolts tightly until you have assembled all other parts. 1 Align the main front support bar (12) with the top/front hole in the main leg assembly (9), then secure with a M6 × 50 mm bolt (L) and a hex wrench (M).
STEP 14: Connect the main leg assembly and side leg assembly You need: L M6 × 50 mm bolt J M6 × 15 mm bolts (4) M Hex wrench Note: To make assembly easier, do not lock the bolts tightly until you have assembled all other parts. 1 Align the bottom support bar (13) connected to the main leg assembly with the bracket on the center leg (16), then secure with two M6 × 15 mm bolts (J) and a hex wrench (M).
L-Shaped Computer Desk STEP 15: Secure the main leg assembly and side leg assembly You need: L M6 × 50 mm bolt M Hex wrench Note: To make assembly easier, do not lock the bolts tightly until you have assembled all other parts. 1 Align the end of the side front support bar (15) with the hole on the main back support bar (11), then secure with a M6 × 50 mm bolt (L) and a hex wrench (M). 2 Have someone help you lift the leg assembly into an upright position. BOTTOM/BACK TOP/FRONT www.insigniaproducts.
STEP 16: Attach the desktops to the leg assembly You need: 8 Side desktop E M6 × 30 mm bolts (13) F Washers (13) M Hex wrench Note: To make assembly easier, do not lock the bolts tightly until you have assembled all other parts. 1 22 Have someone help you lift the main desktop (7) on top of the main leg assembly. Make sure that the holes underneath the main desktop align with the holes in the leg assembly.
L-Shaped Computer Desk STEP 17: Attach the cross bars to your desk You need: 17 Cross bars (2) 1 I M5 × 15 mm bolts (8) M Hex wrench Secure each set of cross bars (17) to the back of the leg assemblies with M5 × 15 mm bolts (I) and the hex wrench (M). www.insigniaproducts.
STEP 18: Secure your desk to the wall You need: H Anchors (2) K 5 × 50 mm screws (2) G Screw covers (2) Phillips #2 screwdriver Hammer Drill with M8 bit (For wall mounting only) Pencil WARNING: • DO NOT SKIP THIS STEP. Securing your desk protects children and pets from accidental tip-overs and injury. • The included screws (K) and anchors (H) are intended for securing your desk to drywall only. If your wall is made of a different material, you must purchase appropriate anchors and screws separately.
L-Shaped Computer Desk Cleaning your desk • • Clean the surface of your desk with a duster or damp cloth only. Do not use abrasive cleaners. Specifications Dimensions (H × W × D) 54.4 × 56 × 56 in. (138.3 × 142.3 × 142.3 cm) Weight 89.3 lbs. (40.5 kg) Maximum supported weight Desktop: 100 lbs. (45.4 kg) Hutch: 20 lbs. (9.1 kg) Shelf: 5 lbs. (2.3 kg) Troubleshooting PROBLEM POSSIBLE SOLUTIONS My desk wobbles Place your desk on a solid, sturdy surface. Carpet may cause your desk to wobble.
ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
For product inquiries, please contact us with the information below: 1-877-467-4289 www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2022 Best Buy. All rights reserved.
