Installation Guide

Right
bracket
Left
screw
Right
screw
Right
bracket
Left
bracket
Control cable
Air hose
Leg rest
Leg rest
Right
screw
Left
bracket
Left
screw
Leg rest
Vis gauche
Vis
droite
Support
droit
Support
gauche
Câble de
commande
Tuyau
d'aération
Repose-jambes
Repose-jambes
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and
Canada)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2021 Best Buy. All rights reserved.
INSTALLATION GUIDE
Leg Rest
Installation
NS-MGC600BK2
PACKAGE CONTENTS
• Massage chair
• Leg rest
• Installation Guide
INSTALLING THE LEG REST
1 Remove the screws from the brackets with a
Philips screwdriver. Keep the screws to use
later.
2 Open the bracket covers.
3 Gently pull out the control cable and air hose
from the chair and from the leg rest.
4 Move the leg rest into position in front of the
chair. Connect the control cable and air hose
from the leg rest to the control cable and air
hose on the chair, making sure that the
connections are solid.
5 Push the extra length of the control cable
and air hose into the opening in the chair.
6 Lift the leg rest into position into the
brackets. Make sure that the pivot points in
the leg rest t into the notches in the chair
without binding.
7 Fold down the brackets and replace the two
screws you removed earlier (one in each
bracket), then tighten the screws with a
Phillips screwdriver.
8 Make sure that the leg rest pivots up and
down easily, without binding.
9 Zip up the two halves of the zipper (one on
the leg rest and one on the chair) to cover
the connections.
V1 ENGLISH 21-0772
Final at size: 24.9 × 11.2 in. (632.46 × 285 mm)
Final at size: 8.3 × 11.2 in. (210 × 285 mm)
GUIDE D’INSTALLATION
Installation du
repose-jambes
NS-MGC600BK2
CONTENU DE L'EMBALLAGE
• Fauteuil de massage
• Repose-jambes
• Guide d’installation
INSTALLATION DU REPOSE-JAMBES
1 Retirer les vis des supports à l’aide d’un tournevis
cruciforme. Conserver les vis pour les réutiliser.
2 Ouvrir le couvercle des supports.
3 Retirer délicatement le câble de commande
et le tuyau d'aération du fauteuil et du
repose-jambes.
4 Placer le repose-jambes en position à l'avant
du fauteuil. Connecter le câble de
commande et le tuyau d'aération du
repose-jambes au câble de commande et au
tuyau d'aération du fauteuil, en s'assurant
que les connexions sont solides.
5 Pousser la longueur supplémentaire du câble
de commande et du tuyau d'aération dans
l'ouverture du fauteuil.
NS-MGC600BK2_21-0772_QSG_V1_EN_FR_SP.ai 1 11/4/2021 10:54:18 AMNS-MGC600BK2_21-0772_QSG_V1_EN_FR_SP.ai 1 11/4/2021 10:54:18 AM