INSTALL ATION GUIDE Full Motion Mount for TVs 47" - 90" NS-HTVMM1703-C For VESA patterns: • 7.9 × 7.9" (200 × 200 mm) • 11.8 × 7.9" (300 × 200 mm) • 11.8 × 11.8" (300 × 300 mm) • 15.7 × 7.9" (400 × 200 mm) • 15.7 × 11.8" (400 × 300 mm) • 15.7 × 15.7" (400 × 400 mm) • 19.7 × 15.7" (500 × 400 mm) • 23.6 × 15.7" (600 × 400 mm) Before using your new product, please read these instructions to prevent any damage.
Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS Maximum TV weight: 130 lbs. (59 kg) - SAVE THESE Screen size: 47 in. to 90 in. diagonal INSTRUCTIONS Overall dimensions (H × W ): CAUTION: Do not use this product for any purpose 16.9 × 28 in. (42.9 × 71.1 cm) not explicitly specified by Insignia. Wall-mount weight: 22 lbs. (10 kg) Improper installation may cause We’re here for you property damage or personal injury. If you do not understand these www.insigniaproducts.
Full Motion Mount for TVs 47" - 90" Tools needed You will need the following tools to assemble your new TV wall mount: ardware Pencil Edge-to-edge stud finder Measuring tape Drill Phillips screwdriver Tape Hammer 3/16 in. (5 mm) wood drill bit (for wood stud wall) OR 3/8 in. (10 mm) masonry drill bit (for concrete wall) Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount: Wall Mount (1) TV Brackets (2) www.insigniaproducts.
TV Hardware Bag Label Hardware Qty.
Full Motion Mount for TVs 47" - 90" Installation instructions STEP 1 - Determine whether your TV has a flat back or an irregular or obstructed back 1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. 2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions. 3 Lay the TV brackets, oriented vertically, on the back of your TV.
STEP 2 - Select screws, washers, and spacers 1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV requires, test various sizes by hand-threading the screws.
Full Motion Mount for TVs 47" - 90" STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back 1 Align the left and right TV brackets with the screw holes on the back of the TV. Make sure that the brackets are level. 2 Install washers (A11 or A12), and screws (A1, A3, A5, or A7) into the holes in the back of the TV. 3 Tighten the screws until they are snug against the TV brackets. Do not over tighten.
STEP 3 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed backs 1 Place spacers (A10) over the holes on the back of the TV. 2 Align the left and right TV brackets with the screw holes on the back of the TV. Make sure that the brackets are level. 3 Place washers (A11 or A12) over the holes in the TV brackets. Insert screws (A2, A4, A6, A8, or A9) through the washers, TV brackets, and spacers. 4 Tighten the screws until they are snug against the TV brackets. Do not over tighten.
Full Motion Mount for TVs 47" - 90" STEP 4 - Determine wall-mount location Note: • For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder • Your TV should be high enough so your eyes are level with the middle of the screen. This is normally 40 to 60 in. from the ground. The center of your TV will be offset .8 in. lower than the center of the wall plate on the wall-mount.
STEP 5 - Option 1: Installing on a wood stud* wall Note: Any drywall covering the wall must not exceed 5/8 in. (16 mm). 1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder. 2 Align the center of the wall plate template at the height (a + b) you determined in the previous step, make sure that the template is level, then tape it to the wall. 3 Drill four pilot holes through the template to a depth of 2 in. (50 mm) using a 3/16 in.
Full Motion Mount for TVs 47" - 90" STEP 5 - Option 2: Installing on a solid concrete or concrete block wall 1 2 3 4 CAUTION: To prevent property damage or personal injury, never drill into the mortar between blocks. Mount the wall plate directly onto the concrete surface. Align the center of the wall plate template at the height (a + b) you determined in the previous step, make sure that it is level, then tape it to the wall. Drill six pilot holes through the template to a depth of 2.28 in.
STEP 6 - Install the decorative end caps • Snap a decorative end cap on each end of the wall plate. Decorative end cap You’ll need Decorative end cap (2) 12 www.insigniaproducts.
Full Motion Mount for TVs 47" - 90" STEP 7 - Mount the TV to the wall plate 1 Holding the TV with the top of the screen tilted toward the wall, slide the upper edges of the right and left TV brackets into the notches on the upper lip of the wall-mount arm on the wall mount. 2 Push the bottom of the TV towards the wall until the latch mechanism clicks into place. 3 Press the magnetic ends on the TV brackets ribbons onto the mounting brackets. TV brackets HEAVY! You will need assistance with this step.
STEP 8 - Manage cables 1 Snap the plastic covers onto the top and bottom edges of the wall plate. 2 Thread cables for attached devices through the grooves on the plastic covers, then snap the cable management clips 1 over the plastic covers. 3 Align the cables along the sides of the wall-mount arm, then snap the cable management clips 2 over the cables. Cable management clip 1 Cable management clip 2 Plastic cover You’ll need Plastic cover (2) 14 Cable management clip 1 (2) www.insigniaproducts.
Full Motion Mount for TVs 47" - 90" STEP 9 - Adjust the mount angle 1 To adjust the arm tension (to make the arm easier or harder to move), loosen or tighten the tension screw with an Allen wrench. 2 To rotate the TV left or right, hold the sides of the TV, then push one side while pulling the other side. 3 To tilt of the TV up or down, hold the top and bottom of the TV, then tilt the TV forward or backward. Allen wrench -2° ~ 10° Tension screw ± 180° ± 90° ± 3° You’ll need Allen wrench www.
STEP 10 - Secure the TV to the wall plate • Press the TV brackets against the wall-mounting plate until they lock into place. To remove the TV from the wall mount, pull down on both ribbons on the bottom of the TV brackets to unlock the brackets, then lift the TV off the wall mount. 16 www.insigniaproducts.
Full Motion Mount for TVs 47" - 90" ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
• • • • Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.) Products where the factory applied serial number has been altered or removed Loss or Theft of this product or any part of the product Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated) grouped in an area smaller than one tenth (1/10) of the display size or up to five (5) pixel failures throughout the display.
1-877-467-4289 www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2020 Best Buy.
