User guide

ManualsBrandsInovonics ManualsCommunicationFA206B

03814a.doc LIT-FA206DS-INSTALL hc:24-Apr-03

FA206B

Frequency Agile

900MHz Transmitter

Passive InfraRed Motion Detector

Installation Instructions

03814A

Overview:

The FA206B is an Inovonics transmitter incorporating the Detection Systems RF940U PIR. The

unit operates on a single 3.0V lithium battery (Panasonic CR123A or equivalent). The PIR is

designed to detect indoor movement of human-size infrared targets. With Detection Systems’ Pet

Friendly

feature the sensor will not detect single or multiple animals up to 30 pounds (13.6 Kg)

total weight.

Features:

x

Inovonics' reliable 900 Megahertz

Frequency Agile

radio link.

x

Mounting options permit flat wall, corner or hallway mounting. Optional bracket for special mounting.

x

RF interference immunity.

Specifications:

Dimensions: 4.5" H x 2.5” W x 1.6” D (11.4 cm x 6.4 cm x 4.1 cm)

Operating temperature: 32

F to 120

F (0

C to 49

Humidity: 0 – 85% non-condensing (PIR)

Battery: 1 - 3.0V lithium ( Panasonic CR123A, Duracell DL123A)

Note: Battery is always supervised

Tamper: Housing and wall (optional)

PIR RF interference immunity: Greater than 30 v/m 26 MHz – 1 GHz

Mounting Height: 7 to 9 feet (2.1 to 2.7 meters)

Alarm lockout time: 3 minutes

Options: B335 Swivel and B338 Ceiling mounting brackets

(from Detection Systems)

Important Notes

n

These products are designed to be installed and maintained by professional security technicians.

n

Products, unless specifically noted, are intended for indoor use.

n

Manually test all products regularly.

Summary of content (7 pages)

PAGE 1
FA206B Frequency Agile® 900MHz Transmitter Passive InfraRed Motion Detector Installation Instructions 03814A Overview: The FA206B is an Inovonics transmitter incorporating the Detection Systems RF940U PIR. The unit operates on a single 3.0V lithium battery (Panasonic CR123A or equivalent). The PIR is designed to detect indoor movement of human-size infrared targets. With Detection Systems’ Pet ® Friendly feature the sensor will not detect single or multiple animals up to 30 pounds (13.6 Kg) total weight.
PAGE 2
Installation: Mounting Note: Recommended mounting height range is 7 to 9 feet (2.1 to 2.7 meters). General mounting advice: x For best detection, locate the FA206B so that intruders move across detection coverage patterns, rather than toward or away from the sensor. x The mounting surface should be solid and vibration-free. x Check areas for potential sources of false alarms. Remember that the sensor responds to quick changes in heat patterns within its coverage pattern.
PAGE 3
Next, remove the circuit board / mirror unit from the enclosure. Pull the PCB locking tab toward the side of the housing, then lift the board / mirror unit out of the enclosure. Wall Tamper Switch Wall Tamper Jumper Jumper Off = Enabled Wireless Transmitter PCB Jumper On = Disabled Battery Reset Switch Programming Jumper PCB Locking Tab Housing Tamper Switch For surface or corner mounting, drill two holes in the housing. Mark the location for the mounting screws, using the enclosure as a template.
PAGE 4
Programming the FA206B: Wall Tamper Switch Wall Tamper Jumper Jumper Off = Enabled Wireless Transmitter PCB Jumper On = Disabled Battery Reset Switch Programming Jumper PCB Locking Tab Housing Tamper Switch Programming the transmitter: 1. Remove the FA206B cover. 2. Insert battery as shown. 3. Enter programming mode for the programming device. Set options as desired. Program the FA206B as a Normally Closed (N/C) device. 4.
PAGE 5
Coverage patterns and Zone identification: 20 ft 40 ft 0 0 6m 0 20 ft 6m 0 12 m 3m 10 ft 0 0 Look Down Zone: To enable, peel mask from Look Down lens. If masking is required, refer to the Lens diagram and the corresponding zone identification data to show appropriate lens zones to be masked. Use opaque masking material, such as electrical tape. RFU940U Lens (Inside view) © 2003 Inovonics Wireless Corporation 5 03814a.
PAGE 6
Warranty & Disclaimer Inovonics Wireless Corporation ("Inovonics") warrants its products ("Product" or "Products") to conform to its own specifications and to be free of defects in materials and workmanship under normal use for a period of twenty-four (24) months from the date of manufacture. Within the warranty period Inovonics will repair or replace, at its option, all or any part of the warrantied product. Inovonics will not be responsible for dismantling and/or reinstallation charges.
PAGE 7
Additional products from Inovonics include: Frequency Agile® Receivers FA416 FA416D FA464 16-channel / 4-output 16-channel / 4-output with display 64-channel / 16-output Frequency Agile® Transmitters FA203(S/D) FA205(S/D) FA204 FA206 FA207 FA210(W) pendant transmitter (Single or Double Button) beltclip transmitter (Single or Double Button) pendant transmitter Sharpshooter PIR transmitter glassbreak detector transmitter universal transmitter (optional widegap) FA206B PIR Detector Options B335 Swivel Moun