IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE, Before returning this product call CALL 1-800-4 DEWALT 1-800-4-DEWALT IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT’S QUALITY IMPROVEMENT PROGRAM. Questions? See us on the World Wide Web at www.dewalt.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) FIG.
English Table of Contents Introduction......................................................................................................iii Features & Options ......................................................................................10 Safety and Precautionary Information ....................................................iii System Settings ....................................................................................10 Limitations of the System .................................
damaged, replace only with the DEWALT power supply specified for this equipment to avoid product damage CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR FAILURE. This equipment is supplied with a wall mount power supply designed specifically to operate on 120V 60Hz. Replace only with the DEWALT power supply specified for this unit. CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR FAILURE. Do not use near water. Damage to the equipment may occur.
English • A telephone line, either cellular or landline, is needed to transmit alarm signals to the monitoring system. If reception is not available, telephone lines are out of service, or the telephone company makes changes to its facilities, the outgoing call cannot be placed. • This equipment uses an RJ-11 jack to connect to the telephone network. If another device, such as a telephone, fax or modem, is utilizing the connected phone line, this equipment will not interrupt the device currently in use.
Warnings For your convenience and safety, the following warning labels are on the Base Unit and Key Chain Remote: DS100 BASE UNIT • To reduce the risk of injury, user must read and understand Instruction Manual. • Use only with DEWALT authorized power sources designated for this product. • Not for personal protection. • Contains Lead-Acid battery. Must be recycled or disposed of properly. See Instruction Manual.
ELECTRONIC CHIME TONE When typing on the keypad, there will be a chime that indicates the key was pressed. PRODUCT OVERVIEW English Unique Features KEY PAD INTERFACE Refer to Figure 1 at the beginning of this manual. This system offers several features unique to most security systems. CELLEMETRY® Cellemetry® is a patented two-way wireless data network that uses standard cellular infrastructure to transport small packets of communication messages throughout North America.
JobSite Security Cable Lock: A unique sensor that enables securing of assets by wrapping a cable through mobile equipment, containers, materials, gates or other remote assets for protection. Also provides a location for a standard padlock (not included) providing added security. Container Sensor: A unique sensor that enables monitoring of remote metal containers by measuring vibration. Recommended for use on steel containers, large tool boxes and tool storage boxes.
English If the system is armed and it receives either an Instant alarm signal from a sensor or the entry delay time on a sensor has expired, the system shall enter the Alarm State for 8 minutes. The DEWALT Mounting Bracket (DS001) is recommended for mounting and to secure the Base Unit to a wall or corner. The Mounting Bracket must be purchased separately. CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR FAILURE. This equipment is for indoor use only. Placement in outdoor conditions can damage the unit.
Programming for Initial Setup 3. Using the numbers on the keypad, set the date. The character that is being changed will be underlined. To move back a character, use the down arrow. To move forward a character, use the up arrow. Select SET After power is supplied to the Base Unit, a setup sequence will enable customization of the system. SEVEN EASY STEPS: 1. Choosing a Language 2. Set Time and Date 3. Set Master Code 4. Assign Devices (have Key Chain Remote, sensors and batteries ready) 5. Test Range 6.
2. Re-enter the master code. Select OK. English RESET BUTTON b. Install the battery using the polarity (+ and -) markings on the battery and equipment. Do not use excessive force. If the battery does not fit, check to make sure that it matches the polarity markings. c. When prompted by the Base Unit to RESET DEVICE, press the reset button located inside the Key Chain Remote to register the device. After registering the Key Chain Remote, replace the cover. 4.
IMPORTANT: Write the device description and corresponding device number on the Sensor Location List. Keep this sheet for reference. This information will be needed during the monitoring service enrollment process. The location and descriptions for each device are critical for the monitoring of the system. 6. After editing the device description, select SAVE. Indoor Motion: Wait 90 seconds since last motion was detected then walk through the areas where protection is expected.
English To move forward a character, use the up arrow. To select letters, reference the Alpha/Numeric Chart in the Appendix. IMPORTANT: The vibration sensor in the Base Unit and the tamper in every sensor are automatically set to instant. This setting cannot be changed. The purpose of this setting is to send a notification if an intruder attempts to disable or destroy the device. See Set Delay/Instant under Features and Options for more information.
CAUTION: LOUD NOISE. Using the Key Chain Remote to arm the system will cause a brief loud noise that may startle any persons near the Base Unit. 1. To arm the system, press the lock button on the left side of the Key Chain Remote. 2. For 60 seconds, the screen will display the following message indicating that the system is arming: 5. Use the up and down arrows to scroll through the menu until the Auto Arm ON/OFF screen is displayed. Select OK. 6. When the following screen appears, select CHANGE.
English • Entry Delays • Using the Keypad • Using the Key Chain Remote 1. To disarm the system, press the unlock button on the right side of the Key Chain Remote. 2. The main screen will be displayed. The ARMED light on the unit will be off. ENTRY DELAYS Each sensor aside from the Base Unit motion sensor can be reset for Instant which eliminates the entry delay. By changing a device to instant, when the system is armed an alarm will take place as soon as the device is tripped.
DESCRIPTION OF FAULT CODES NOTE: See the Troubleshooting Guide for more detailed information. 1. Start at the main screen.
English NOTE: Each device has a reset button that must be pressed and released. To locate the reset button, refer to the instructions for each particular device. Be sure that batteries are properly installed in each device. Press the reset button now. 5. The screen will indicate that the device has been registered with the following screen. Only 48 sensors and 6 Key Chain Remotes can be added. If there are no slots available, the screen will display ALL DEVICES IN USE.
6. Re-enter the current master code. This allows verification that the master user is making the change. 7. If a valid master code is entered, the system will ask for a new master code. Using the numbers on the keypad, enter a new four digit master code. Then, select OK. 5. Use the up and down arrows to scroll through the menu until the User Code Maintenance screen is displayed. Select OK. To Add a User NOTE: Up to 6 users including the master user can be programmed. 1.
English 2. Use the up and down arrows to scroll through the users to select the user to be edited. Select EDIT. 4. Continue to delete users or choose EXIT. SET CONSOLE DEVICES The Base Unit contains a siren and a strobe light. They provide notification of an alarm occurrence. Although it is not recommended, the siren and strobe can be turned off and will not operate if an alarm occurs. 1. Start at the main screen. 2. Select MENU or press MAIN MENU on the keypad. 3. Using the keypad, enter the master code.
