SPA DIVISION OF / DIVISION SPA DE Please read this owner’s manual carefully as it is designed to provide you with instructions for the safe use of your new spa.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ............................................................................................................................ 3 INSTALLATION & QUICK START UP GUIDE . ................................................................................................................... 5 SPA OPERATION ...........................................................................................................................................................
IMPORTANT SAFETY INSTRUCTIONS THIS OWNER’S MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS. READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY AND KEEP THEM HANDY. Most cities, counties, states/provinces and countries require permits for exterior construction and electrical circuits. In addition, some communities have safety codes requiring the property to be equipped with residential barriers such as fencing and/or selfclosing gates to prevent unsupervised access by children to pools or hot tubs.
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY. 1. When installing and using this equipment, basic safety precautions should always be followed. 2. WARNING! This product is provided with a ground fault interrupter (GFCI) as part of the attachment plug. The GFCI must be tested before each use. Press test button. 3. WARNING! DO NOT PERMIT CHILDREN TO USE THIS PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES. 4.
INSTALLATION AND QUICK START UP GUIDE Follow these instructions for quick and easy start up of your new spa. If you have any questions concerning start up, contact your dealer or InnovaSpa (Lumi-O | Innovaplas inc) directly for help. OUTDOOR INSTALLATION If you are going to install your spa outdoors, select a solid, level surface to place it on. The bottom of your spa is totally protected and it will not rot.
INSTALLATION AND QUICK START UP GUIDE 5. FILLING THE SPA: To fill your spa, remove the filter cover and the filter cartridge by turning it counter clockwise. If your source water contains metals, such as iron, it is recommended that you attach a pre filter to your garden hose. This will help to remove any precipitated metals and to make start up easier. Put your garden hose into the threaded hole where the filter cartridge is located and begin to fill your spa through this hole.
SPA OPERATION JETS Operating the jets is very simple. There is a “Jets” button on the top side control panel. Depress the button once and the spa will begin to operate on low speed. Depress the button a second time and the spa will turn on to high speed. Depress the button a third time and the spa will turn off. If the spa is in filter cycle or heat demand, it will continue to operate on low speed. Each jet is individually adjustable and the intensity can be increased or decreased for your desired comfort.
OZONE GENERATOR INSTALLATION The Urbania is manufactured with “Ozone Ready” plumbing. If you want to install an ozone generatorr, follow the instructions below. Installation should be done when the spa is empty. OZONE GENERATOR INSTALLATION - VS300 Spa Pack Overview After installation and with the spa running on low speed, there will be a slight bluish glow coming from the small hole on the bottom of the ozonator.
OZONE GENERATOR INSTALLATION Figure 1.6 Figure 1.7 Figure 1.8 Figure 1.9 Figure 1.10 OZONE GENERATOR INSTALLATION - VS300 Spa Pack (continued...) 7. Connect the 6” end of the tubing to the barb on the injector and secure the Hartford loop into the insulation above the spa cavity opening. (see fig. 1.6) 8. Drill a ¼” hole in the left edge 3” down from the corner. Drill a second hole 9-¼” below the first. Carefully replace the insulation leaving enough space to mount the ozone generator. (see fig. 1.
OZONE GENERATOR INSTALLATION PRE INSTALLATION 1. The ozone generator or UV sterilizer must be 110V and approved for use on residential spas. 2. A Mazzei 784K, or equivalent, injector is required for the ozone generator installation. 3.
ROUTINE MAINTENANCE Your spa will require periodic maintenance to ensure that you maintain clean and healthy water, a safe spa and a clean and healthy spa environment. By performing regular maintenance, your spa will provide you with many trouble-free years of therapy and enjoyment. FILTER Your spa contains a filter cartridge that was designed to trap and remove particles from the spa water. This ensures that your water will remain crystal clear and pleasant to bathe in.
COVER MAINTENANCE AND WINTERIZING YOUR SPA Clean the outer surface of the cover using mild detergent, warm water and a soft brush or cloth. Thoroughly rinse the cover after cleaning. Never use cleaners that contain harsh abrasives or rubbing and buffing compounds as they may permanently damage your cover’s surface.
UNDERSTANDING SPA CHEMICALS AND HOW THEY ARE USED As a new spa owner, it is very important that you learn and understand how to keep your spa water clean and healthy. This short guide was designed to give you a basic explanation of the most common chemicals used in spas and when they are needed. This information was designed to give you a simple understanding of spa chemicals and how, where, when and why they are used.
SPECIALTY CHEMICALS Specialty chemicals address occasional water problems and help to maintain clean, clear water when a spa is heavily used. Whether you will or should use these chemicals will be based on the quality of your source water and how frequently your spa is used. Following is a summary of the most common specialty chemicals and when they should be used. 1.
DISINFECTING AND SANITIZING CHEMICALS There are many different systems available to disinfect and sanitize your spa. The system that you choose should be geared to the frequency of usage of your spa and who is using it. Following are five traditional systems that address different preferences and usage parameters. You should choose the system that is best suited for you. BROMINE Bromine is a sanitizer that is best suited for use in spas.
TROUBLESHOOTING If you are experiencing an operating problem, it is recommended to contact your spa dealer or a qualified service technician to arrange servicing. Some problems can be disgnosed and rectified with a simple action or procedure. Below are some common problems, possible causes and simple actions that may help to solve them. THE CIRCUIT BREAKER IMMEDIATELY TRIPS WHEN THE SPA IS STARTED 1.
TROUBLESHOOTING MY WARRANTY HAS EXPIRED InnovaSpa (Lumi-O | Innovaplas inc) will continue to provide service for your spa even after your warranty has expired via our customer care center at 1-866-995-8646, extension 226. DRAINAGE FREQUENCY The frequency of draining your spa and cleaning or replacing your filter will be determined by your sanitation program. Consult your dealer for recommendations.
DIAGNOSTIC MESSAGES MESSAGE MEANING ACTION REQUIRED No message displayed. Power to the spa has been cut off. The control panel will be disabled until power returns. -- -- Temperature unknown After the pump has been running for two minutes, the temperature will be displayed. Spa settings will be preserved until next start up. HH Overheat. The spas has shut down. One of the sensors has detected a 118°F (48°C) temperature at the heater. Do not enter the water.
