User's Manual

ManualsBrandsInnoComm Mobile Technology ManualsElectronicsWiFi Module

iCOM_WM05_AN Module EVB_QSG

REV 0.1 8/14/2015

InnoComm Mobile Technology Corporation

3F, No. 6, Hsin Ann Rd., Hsinchu Science Park, Hsinchu 30078, Taiwan

TEL: +886-3-5781868 FAX: +886-3-5781187

User Manual

Model name: WM05_AN

FCC ID: YAIWM05-AN

Summary of content (13 pages)

PAGE 1
iCOM_WM05_AN Module EVB_QSG 8/14/2015 REV 0.1 InnoComm Mobile Technology Corporation 3F, No. 6, Hsin Ann Rd.
PAGE 2
iCOM_WM05_AN Module EVB_QSG 8/14/2015 REV 0.1 [General Information] The WM05_AN Evaluation Module Kit contains two WM05_AN (TI CC3200) modules supported USB to UART interface which is prepared for WiFi performance testing purpose. WM05_AN module provides excellent low power consumption with astonishing wireless connection range. Part Number WM05_AN Photo Description WiFi module Size (mm) Pin count Mounting Method Supply Voltage 20.5x24x2.3 63 SMD 2.5V ~ 3.
PAGE 3
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 EVB Drive FTDI2232D Uniflash: http://www.ti.com/tool/uniflash Radio Tool: http://www.ti.com/tool/cc3xxxradiotest [EVB] Uniflash (to flash applications): 1. Please make sure programmer jumper is closed. Once Uniflash is installed (uniflash_cc3xxx_setup_3.2.0.00019.exe), invoke ‘CCS UniFlash’.
PAGE 4
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 2. ‘CCS UniFlash’ will open like below. 3. Go to ‘New Target Configurations’ and do the settings as shown below.
PAGE 5
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 4. Select the correct COM port. For correct COM port please see the next section, ‘Radio tool (to control the device)’. 5. Click on /sys/mcuimg.bin and browse for required binary file For example, flashing the launchpad with the ‘Radio Tool Application’, select the following binary available in the path shown below: C:\ti\CC3XXXRadioTool-0.5\CC32xxBoardApplication_Binary\RadioTool_V1p1_PG1p32.bin Check ‘Erase’ and ‘Update’.
PAGE 6
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 6. Go back to ‘CC31x Flash Setup and Control’ and click ‘Program’ After programming the device remove programmer jumper. This removal is VERY important before any testing to be done. Reset the board using the RESET push-button  Radio tool (to control the device): 1. Once the device is powered up (after connecting uUSB cable to ‘power jumper’), one COM port should be enumerated in the device manger.
PAGE 7
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 The Radio Tool GUI will appear as shown below. 3. For CC3200 module launchpad, select CC3200 UART as ‘Device’. Select the COM port found in device manager. please select COM25 as shown below. Click ‘Connect’.
PAGE 8
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 4. Once the device is connected, the GUI would show ‘Chip ID’, ‘ROM Ver’, ‘FW Ver’ and ‘MAC Address’ 5. For RX measurements go to ‘RX’ tab of the Radio Tool GUI. Select the channel intended and set the duration (example 5secs). Click ‘Start RX Testing’ and after 5 secs, the statistics will appear in the GUI.  6.
PAGE 9
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 The steps are similar to other rates as well. For TX measurements go to ‘TX’ tab. Before starting TX operations following settings need to be done on the GUI.  TX Mode: Select ‘Packetized’  Rates: Select the modulation rates want to transmit o 11b: 1, 2, 5.5 and 11 Mbps o 11g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps o 11n: MCS0 to MCS7  Channel: Select the channel of transmission.
PAGE 10
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 Picture 20 If to change channel or modulation rate please first click ‘Stop TX testing’. If Change To new channel or modulation rate is OK, Please click ‘Start Tx Testing’ TX -> change settings -> start TX sequence to be followed.
PAGE 11
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 Picture 22 Picture 22: Example of 11n (MCS7) transmission at channel 7(2442MHz) [Software application development] Development support  The CC3200 includes a set of tools and documentation to help the user during the development phase.  PinMux Tool: The CC3200 device uses pin multiplexing extensively to accommodate the large number of peripheral functions in the smallest possible package.
PAGE 12
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 13
REV 0.1 iCOM_WM05_AN Module EVB_QSG 8/14/2015 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.