Use and Care Manual

ManualsBrandsINKBIRD ManualsHeatingPre-Wired Dual Stage Thermostat Temperature and Humidity Controller

Code Symbol Function Setting Range

Default

Setting

HS HS

Humidity Setting

Value

5.0%RH ~99.0%RH 50.0%RH

Humidiﬁcation

Difference Value

1.0%RH ~20.0%RH 5.0%RH

Dehumidiﬁcation

Difference Value

1.0%RH ~20.0%RH 5.0%RH

AH AH

Alarm High Humidity

Limit

5.0%RH ~99.0%RH 99.0%RH

Alarm Low Humidity

Limit

5.0%RH ~99.0%RH 5.0%RH

Compressor Delay

Time

0~10 minutes 0 minute

CA CA Humidity Calibration -20.0%RH ~20.0%RH 0.0%RH

3.2 Setting Menu Instruction

4.Control Function Instruction

4.1 Setting Humidity Control Function ( HS ,HD, DD )

When the controller works normally, PV shows the measured

humidity, meantime SV shows the humidity setting value, and

automatically recognizes and converts for the humidiﬁcation

and dehumidiﬁcation working mode .WORK1 is the humidiﬁca-

tion output, furthermore the red led is the WORK1 humidiﬁca-

tion output status indicator; WORK2 is dehumidiﬁcation

output, furthermore the green led is WORK2 dehumidiﬁcation

output status indicator.

When PV(measured humidity) ≤ HS(humidity setting value) –

HD(humidiﬁcation difference value), the controller will enter

into the humidiﬁcation state, the red led is on, WORK1 output

works. When PV(measured humidity) ≥ HS(humidity setting

value), the red led is off and the WORK1 output turns off.

When PV(measured humidity) ≥ HS(humidity setting value) +

DD(dehumidiﬁcation difference value), the controller will enter

into the dehumidiﬁcation state, the green led is on, WORK2

output works; green led flashes, indicating that the dehumidi-

ﬁcation device is in delay protection state. When PV(measured

humidity) ≤HS( humidity setting value), the green led is off and

the WORK2 output turns off.

For example, when setting HS=50.0%RH，DD=5.0%RH，

HD=8.0%RH, measured humidity value ≥55.0%RH(HS+DD),the

controller will enter the dehumidiﬁcation state, when

measured humidity value ≤50.0%RH, dehumidiﬁcation will

Functions on screen

PV：

In normal mode, the measured humidity is displayed. In

settings mode, it will display menu code.

SV：In normal mode, the humidity setting value is displayed.

In setting mode, it will display the setting value.

Output(WORK1/WORK2) Instruction

WORK1:

The humidif ication output

WORK2: The dehumidif ication output

Indicator LED:

●Red LED is on WORK1 output is on.

●Green LED is on WORK2 output is on.

●Green LED is blinking WORK2 output is performing the

function of compressor delay.

●Yellow LED is on The controller is in the setting mode.

Button Instruction

Please read the detail on 2.Button Operation Instructions

below

Probe interface

Humidity probe can be insert into P1 or P2 interface.

humidity probe

If the controller display Er, you may get a false humidity

probe, please try harder to insert the probe and rotate it to

make good contact. If the problem is still persists, it is likely

the internal probe wire has been damaged by the moisture or

heat temperature.

The probe and cable cannot be touched by the flame.

Do not exceed the probe humidity or temperature range to

avoid damaging

2 Button Operation Instructions

2.1 Restore Default Settings

Press " " button to power on, the buzzer will make a short

call, indicating that all parameters of the user's humidity probe

function return to the default setting value.

2.2 “ ” and “ ”Button Function in Normal Operation

Mode

Press " ", PV shows HD, SV shows humidif ication difference

value; press " ", PV shows DD, SV shows dehumidiﬁcation

difference value, and it will be back to the normal display if

there is no operation for 3 seconds or pressing the "

SET"

button.

2.3 “SET” Button Function in normal operation mode

Short press the “

SET” button to enter the quick setting

humidity setting value mode. SV shows the humidity value

and flashes, and short press “ ” or “ ” button to increase or

decrease the setting value, long press “ ” or “ ”button to

quickly increase or decrease the setting value, and press the

SET" button again to conﬁrm and exit. If there is no operation,

it will automatically exit after 10 seconds and save the setting

value.

2.4 Button Function in Setting Mode

When the controller is working normally, press the “SET”

button for 2 seconds to enter the setting mode, the PV screen

shows the ﬁrst menu code “

HS” and the SV shows the

corresponding setting value. Press “

SET” button to scroll

down the menu item and save the parameters of the previous

menu item. Press “ ” or “ ”button to change the current

setting value. If in the setting state, there is no button

operation within 30 seconds or long press "

SET" button for 2

seconds, exit and save the setting state, return to normal

operation mode.

Output(WORK1/WORK2) Instruction

WORK1: The P1 heating/cooling output

WORK2: The P2 heating/cooling output

Indicator LED:

●Red LED is on WORK1 output is on.

●Red LED is blinking WORK1 output is performing the

function of compressor delay.

●Green LED is on WORK2 output is on.

●Green LED is blinking WORK2 output is performing the

function of compressor delay.

●Yellow LED is on The controller is in the setting mode.

Button Instruction

Please read the detail on 2.Button Operation Instructions below

Probe interface

Two temperature probes can be insert into P1 and P2 interface.

Temperature probe

●If the controller display Er, you may get a false temperature

probe, please try harder to insert the probe and rotate it to make

good contact. If the problem is still persists, it is likely the

internal probe wire has been damaged by the moisture or heat

temperature.

●The probe and cable cannot be touched by the flame.

●Do not exceed the probe temperature range to avoid

damaging.

2 Button Operation Instructions

2.1 Restore Default Settings

Press and hold the “ " button to power on, the buzzer will

make a short call, indicating that all parameters of the user's

temperature and humidity probe function return to the default

setting value.

2.2 “ ” and “ ”Button Function in Normal Operation

Mode

Press the “ ", PV shows the current temperature setting

value , SV shows current humidiﬁcation value; press “ ", PV

shows current temperature value, SV the current humidiﬁcation

setting value , and It will be back to the normal display if there is

no operation for 3 seconds orpressing the "

SET" button.

2.3 “SET” Button Function in Normal Operation Mode

Short press the “

SET” button to enter the quick setting

temperature and humidity value mode. PV shows the current

temperature setting value and flashes, and short press “ ” or

“ ” button to increase or decrease the setting value, long

press “ ” or “ ”button to quickly increase or decrease the

setting value, Short press the “

SET” button again，SV shows

the current humidity setting value and flashes, and short press

“ ” or “ ” button to increase or decrease the setting value,

long press “ ” or “ ”button to quickly increase or decrease

the setting value and lastly press the "

SET" button again to

conﬁrm and exit. If there is no operation, it will automatically

exit after 10 seconds and save the setting value.

2.4 Button Function in Setting Mode

When the controller is working normally, press the “SET” button

for 2 seconds to enter the setting mode，the PV shows the ﬁrst

menu code“

”, SV shows the corresponding setting value.

Press “

SET” button to scroll down the menu item and save the

parameters of the previous menu item. Press“ ” or

“ ”button to change the current setting value. Selected T to

enter the temperature parameter modiﬁcation mode; selected H

to enter the humidity parameter modiﬁcation mode. If in the

setting state, there is no operation within 30 seconds or long

press "

SET" button for 2 seconds, it will exit and save the

setting state and return to normal operation mode.