Owners manual

ManualsBrandsINJEN ManualsAutomotiveInjen PF2055P Power-Flow Air Intake System Fits 99-04 4Runner Tacoma

Part numberPF2055

1999-04 Toyota Tacoma V6 3.4L

1999-02 Toyota 4Runner V6 3.4L

1- MR Tech tuned air intake (SR)

1- 3 1/2” Injen filter w/inv top (#1021)

1- 2 3/4” straight hose (#3043)

1- 19” -10mm vacuum hose (#3076)

1- 27” -6mm vacuum hose (#3087)

2- Power-bands .312 .040 (#4003)

1- m6 vibra-mount (#6020)

2- m6 flange nut (#6002)

2- fender washer (#6011)

1- instruction

Note: The C.A.R.B. Exempt sticker must be

attached under the hood in a manner such that

it is easily viewed by an emissions inspector.

Congratulations! You have just purchased the best engineered,

dyno-proven cold air intake system available.

Please check the contents of this box immediately.

Report any defective or missing parts to the Authorized Injen

Technology dealer you purchased this product from.

Before installing any parts of this system, please read the instructions

thoroughly. If you have any questions regarding installation please

contact the dealer you purchased this product from.

Installation DOES require some mechanical skills. A qualified

mechanic is always recommended.

*Do not attempt to install the intake system while the engine is hot.

The installation may require removal of radiator fluid line that may

be hot.

Injen Technology offers a limited lifetime warranty to the original

purchaser against defects in materials and workmanship. Warranty

claims must be handled through the dealer from which the item was

purchased.

Injen Technology 285 Pioneer Place Pomona, CA 91768 USA

Please check the contents of this box immediately.

Note: This intake system was Dyno-tested with an Injen filter and

Injen parts the use of any other filter or part will void the

warranty and CARB exemption number.

Parts and accessories are available on line at “Injenonline.com

Note: The installation of this cold air intake does require mechanical skills. Removal of the front bumper requires

loosening and removing several plastic plugs and screws that may be difficult. In addition to removing the

bumper, you will also have to remove the air resonator box, battery and tray when beginning this installation.

Injen strongly recommends that this system be installed by a professional mechanic.

MR Technology, “The World’s First Tuned Intake System!”

Optimum performance, Factory safe air/fuel ratio.

Patent Pending

“An air intake evolution”

Tools required:

1. Phillips screwdriver

2. Rachet

3.12mm socket

4. 10mm socket

5. 8mm nut driver

Summary of content (4 pages)

PAGE 1
Tools required: 1. Phillips screwdriver 2. Rachet 3.12mm socket 4. 10mm socket 5. 8mm nut driver Part numberPF2055 1999-04 Toyota Tacoma V6 3.4L Congratulations! You have just purchased the best engineered, 1999-02 Toyota 4Runner V6 3.4L dyno-proven cold air intake system available. 1111121221- MR Tech tuned air intake 3 1/2” Injen filter w/inv top 2 3/4” straight hose 19” -10mm vacuum hose 27” -6mm vacuum hose Power-bands .312 .
PAGE 2
Prior to starting this installation, disconnect the negative battery terminal. Disconnect the stock 6mm vacuum line connected to the small intake manifold port. This line will be replaced with the 27” 6mm vacuum hose. Disconnect the stock 8mm breather hose connected to the air intake box port. This line will be reused and connected to the first 1/2” port nearest to the filter. (A) >> >> >> >> Remove the 6mm bolt located on the cross member.
PAGE 3
(B) B) (A) (A) Once the vibra-mount has been inserted into the hole use the m6 flange nut and washer to hold the vibra-mount from underneath the wheel well(A). The vibra-mount should be firmly in place next to the cruise control box (B). Unscrew the stock screws and remove the mass air flow sensor from the air intake box (A). Slowly, insert the mass air flow sensor into the machined MAF sensor flange as shown above (B).
PAGE 4
(C) >> >> (A) (B) The intake bracket is secured with the m6 nut and washer (A). The stock 8mm hose from the crank case is also secured with the clamp (B) and the 6mm Injen hose is also installed (C). The harness clip is reconnected to the MAF sensor. Press the clip over the sensor until you here it snap in place. Congratulations! The intake is now install and the Injen vacuum lines have been installed. 1.