ALL WEATHER W-SERIES AND WD-SERIES QUARTZ TUBE ELECTRIC INFRARED RADIANT HE TABLE OF CONTENTS Warnings 2 Installation Instructions 3 Wiring Instructions 3 Mounting Instructions 4 Replacement Element Installation 5 Replacement Parts 5 Heater Coverage Areas 6 General Notes 6 Maintenance Instructions 6 Trouble Shooting 7 Location Suggestions 7 Warranty 8
WARNINGS READ ALL INSTRUCTIONS BEFORE USING HEATER Unit may be a source of possible shock. NEVER attempt to service heater without disconnecting its power source. Source of possible ignition. CAUTION High Temperature, risk of fire, keep electrical cords, drapery, furnishings and other combustibles at least 3 feet (0.9m) from the front of heater and away from sides and rear. MOUNTING HEIGHT/CLEARANCES CLEARANCE FROM COMBUSTIBLES MIN 6” (15.2cm) CLEARANCE BEHIND HEATER MIN. 18” (45.
INSTALLATION INSTRUCTIONS This heater must be permanently installed and hard wired by a licensed electrician in accordance with local electrical codes. Assembly procedure must be performed with no electrical power to unit. Step 1: Check UL/CUL/CE label on heater for proper voltage. Step 2: Follow supplied wiring instructions. (See wiring instructions below) Step 3: Heater must be mounted with reflector angled down.
MOUNTING INSTRUCTIONS surface. Installation Installation must must be be such such that that These models may be chain or bracket mounted to any ceiling or horizontal surface. (45.7cm) minimum 18” (45.7cm) minimum clearance clearance isis maintained maintained around around the theheater heater on on all all44 sides sides and and 36” 36” (91.4cm) (91.4cm)directly directlyin infront. front. A minimum of 6” (15.24cm) of of clearance provided by mounting brackets is required behind the plane of the face.
(Visit infratech-usa.com for video instructions) REPLACEMENT ELEMENT INSTALLATION Disconnect grasping itit in in the the middle, middle, flex flex grill grill up up and and lift lift ititoff. off. Disconnect the power at the breaker. Remove the grill by grasping Unscrew element clips clips at at each each end end of ofthe theheater heaterand andremove removenuts nutsfrom from Unscrew and remove both end reflectors. Unhook element end quartz tube. tube.
SINGLE ELEMENT HEATERS COVERAGE AREAS MODEL MOUNTING HEIGHT WATTS MOUNTING AVERAGE AVERAG COLD COLD PROTECTED PROTECTED W-1512 SS 1,500 1,500 6’ - 8’ (1.8m (1.8m- 2.4m) - 2.4m) 5’ 5’ x 5’ (1.5mxx1.5m) 1.5m) (1.5m 3’ (0.9m x 0.9m) 3’ x 3’ (0.9m x 0.9m) 7’xx7’ 7’ 7’ (2.1mx x2.1m) 2.1m) (2.1m W-2024 SS 2,000 2,000 7’ - 9’ (2.1m (2.1m- 2.7m) - 2.7m) 6’ 6’ x 6’ (1.8mxx1.8m) 1.8m) (1.8m 4’ (1.2m x 1.2m) 4’ x 4’ (1.2m x 1.2m) 8’xx8’ 8’ 8’ (2.4mx x2.4m) 2.4m) (2.
TROUBLESHOOTING PROBLEM WHAT TO DO Heater does not glow • Check supply voltage to confirm it matches voltage of heating element. Low heat output Heater • A 240V element connected to 110V or 208V will warm, but not glow orange or generate sufficient heat for typical applications (Matching your voltage is extremely important). If element is visibly orange, but there is insufficient heat, refer to the areas covered with respect to conditions and mounting heights.
LIMITED PRODUCT WARRANTY Model #: Serial #: Date of Purchase: Purchased From: Thank you very much for purchasing a INFRATECH Quartz Tube Electric Heater. We have designed this heater to provide you and your family with many years of great outdoor experiences. Please fill in the Model and Serial number as well as date of purchase in the areas indicated above. Please save this information for future reference.
