Reference Manual

MINIMUM
2" X 8"
FRAMING
SUBFLOOR 5/8" TYPE X DRYWALL
(1 HOUR FIRE RATED)
4' HIGH TEMP FIXTURE WHIP WITH CONNECTORS PROVIDED.
CONNECTION MADE AT HEATER JUNCTION BOX.
ACCESSIBLE
JUNCTION BOX
MOUNTED
OUTSIDE OF
SEALED POCKET
(LONGER LENGTH
HIGH TEMP WHIPS
ALSO AVAILABLE
FOR PURCHASE)
2" X 8" STUDS MINIMUM
MINIMUM OPENINGS
37" FOR 33" HEATERS | 43" FOR 39" HEATERS | 65.25" FOR 61" HEATERS
5/8" DRYWALL WITH 1-HOUR FIRE RATING MUST LINE AND SEAL ALL 5 SIDES OF CAVITY
11.75"
SIDE VIEW
47" FOR 39” HEATERS | 70.25" FOR 60" HEATERS
ADJUSTABLE TABS
3.75"
4"
SURFACE VIEW
Proper Flush Mount Installation
4
Mounting Options
Flush mount your heater in four simple steps
Frame the pocket that will house the heater with a
one hour-rated fire containment box. Note: Frame and
heaters cannot be mounted on a sloped/pitched ceiling.
The junction box must be mounted outside of the lined
pocket. You can choose to mount the junction box in
a variety of locations, depending upon where you’ll be
accessing it.
Install the frame into the finished pocket. You may
choose to leave all four inches of the trim exposed,
or partially cover it with a decorative ceiling
(1/2" clearance is required from ventilation holes).
Install the heater (heater must face horizontal to the
floor) and adjust the tabs to set the heater flush with
finished ceiling.
STEP
1
STEP
3
STEP
2
STEP
4
For video instructions of proper flush mount installation, visit www.infratech-usa.com or scan.
WARNING: FRAME AND HEATERS CANNOT BE FLUSH MOUNTED ON A SLOPED/PITCHED CEILING. FLUSH MOUNT
APPLICATIONS MUST ALWAYS BE INSTALLED WITH HEATERS HORIZONTAL TO THE FLOOR ON A FLAT, NON-SLOPED CEILING.
MINIMUM
2" X 8"
FRAMING
SUBFLOOR
5/8" DRYWALL WITH
1 HOUR FIRE RATING
2 X 8 STUDS MINIMUM
MINIMUM OPENINGS
37" FOR 33" HEATERS | 43" FOR 39" HEATERS | 65.25" FOR 61" HEATERS
5/8" DRYWALL WITH 1-HOUR FIRE RATING (LINE ALL 5 SIDES OF CAVITY)
11.75"
FIXTURE WHIP W/ HIGH
TEMP CONNECTORS
(PROVIDED) CONNECTION
MADE AT JUNCTION BOX
JUNCTION BOX MUST
BE MOUNTED OUTSIDE
OF THE LINED POCKET
(TOP OR SIDE)
SIDE VIEW
41" FOR 33" HEATERS | 47" FOR 39" HEATERS | 70" FOR 61" HEATERS
3.75"
4"
SURFACE VIEW
MINIMUM
2" X 8"
FRAMING
SUBFLOOR
5/8" DRYWALL WITH
1 HOUR FIRE RATING
2 X 8 STUDS MINIMUM
MINIMUM OPENINGS
43" FOR 39” HEATERS | 65.25" FOR 61" HEATERS
5/8" DRYWALL WITH 1-HOUR FIRE RATING (LINE ALL 5 SIDES OF CAVITY)
11.75"
FIXTURE WHIP W/ HIGH
TEMP CONNECTORS
(PROVIDED) CONNECTION
MADE AT JUNCTION BOX
JUNCTION BOX MUST
BE MOUNTED OUTSIDE
OF THE LINED POCKET
(TOP OR SIDE)
ADJUSTABLE TABS
3.75"
4"
MINIMUM
2" X 8"
FRAMING
SUBFLOOR 5/8" TYPE X DRYWALL
(1 HOUR FIRE RATED)
4' HIGH TEMP FIXTURE WHIP WITH CONNECTORS PROVIDED.
CONNECTION MADE AT HEATER JUNCTION BOX.
ACCESSIBLE
JUNCTION BOX
MOUNTED
OUTSIDE OF
SEALED POCKET
(LONGER LENGTH
HIGH TEMP WHIPS
ALSO AVAILABLE
FOR PURCHASE)
2" X 8" STUDS MINIMUM
MINIMUM OPENINGS
37" FOR 33" HEATERS | 43" FOR 39" HEATERS | 65.25" FOR 61" HEATERS
5/8" DRYWALL WITH 1-HOUR FIRE RATING MUST LINE AND SEAL ALL 5 SIDES OF CAVITY
11.75"
SIDE VIEW
47" FOR 39” HEATERS | 70.25" FOR 60" HEATERS
ADJUSTABLE TABS
3.75"
4"
SURFACE VIEW