iSwitch SDV-TR SDVOE Transceiver with Copper/Fiber Combo Box VER 1.0 www.infobitav.
Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.
1. Introduction This transceiver is a SDVoE-Compliant, All-In-One AV over IP solution that provides highest-quality, uncompressed 4K and zero-frame latency audio/ video extension over a standard 10G Copper or Fiber network switch with instant switching, video wall and multi-viewer functions. It can transfer advanced HDMI content such as HDR (high dynamic range), 10-bit color and multi-channel HD Bitstream audio in pass-through mode.
3. Package Contents ① 1 x SDVOE Transceiver ② 1 x 12V IR Receiver cable (1.5 meters) ③ 1 x IR Blaster cable (1.5 meters) ④ 1 x 4-pin 3.81mm phoenix connector ⑤ 1 x 12V/2.5A Locking power adapter ⑥ 2 x Mounting ears ⑦ 4 x Machine screws (KM3*6) ⑧ 1 x 10KM SFP+ 10G optical module ⑨ 1 x User Manual 4. Specifications Technical HDMI Compliance HDMI 2.0b HDCP Compliance HDCP 2.
Connection Input ports 1 x HDMI IN [Type A, 19-pin female] 1 x USB HOST [Type B, 4-pin female] 1x IR IN [3.5mm Jack] 1x AUDIO IN [3.5mm Jack] 1 x RS-232 [4-pin phoenix connector] Output ports 1 x HDMI OUT [Type A, 19-pin female] 1x AUDIO OUT [3.5mm Jack] 1 x IR OUT [3.5mm Jack] 2 x USB 2.0 [Type-A, 4pin female] 1 x 10G BASE-T [RJ45 jack] 1 x 10G SFP+ [Fiber slot] 1 x 1G LAN [RJ45 jack] Mechanical Housing Color Metal Enclosure Black Dimensions 204mm [W] x 134mm [D] x 21.
5. Operation Controls and Functions 5.1 Front Panel POWER STATUS LINK VIDEO USB ENC DEC RESET 1 No. 1 2 3 4 5 6 7 8 9 10 11 2 3 4 5 6 7 8 MODE USB DEVICES USB HOST 9 10 11 Name Function Description Restore default settings button. Press and hold this button RESET button for 5 seconds in the power-on state to restore the default settings. POWER LED When the product is powered on, the red power LED will be on. (Red) System status indicator.
5.2 Rear Panel SFP+ 12V TX RX DC 12V 1 No. IN RS-232 IR IN 2 3 IR OUT 4 Name 1 DC 12V 2 RS-232 3 4 IR OUT port 5 HDMI IN port 6 HDMI OUT port IR IN port HDMI IN HDMI OUT 10G BASE-T 5 6 7 OUT AUDIO 8 9 10 11 Function Description DC 12V power input port. Connect to PC or control system with a 4-pin phoenix connector cable for RS-232 signal pass-through or firmware update. ‘12V’ means that the product can supply power to the outside. IR signal input port.
5.3 IR Pin Definition IR RECEIVER IR BLASTER IR BLASTER + - IR RECEIVER Power 12V 6. Rack Mounting Instruction 6.1 5.5U Rack Mounting This transceiver can be mounted in a standard 5.5U rack (Please contact your supplier for 5.5U rack sale).
Step 2: Insert the transceiver with mounting ears into a 5.5U rack (up to 10 units can be installed vertically), as shown in the figure below: Step 3: Use screws to fix mounting ears on the rack to complete the mounting, as shown in the figure below: 6.2 1U Rack Mounting This transceiver also can be mounted in a standard 1U rack (up to 4 units can be installed horizontally).
Step 2: Fix two 1U rack panels on another two stacked transceivers in the same way, then use screws to fix two 1U rack panels together, as shown in the figure below: Step 3: Fasten screws between two 1U rack panels, so that four transceivers are mounted in a 1U rack, as shown in the figure below: 7. SDVOE System Control For details of SDVOE system control, please refer to SDVOE controller box user guide.
8. Preview Stream Introduction 8.1 Connecting Web for Control This transceiver supports playing video stream on computer via the corresponding software such as VLC media player, simultaneously you need to connect build-in Web GUI to control the video stream play. Default IP of the Web GUI is 169.254.3.1. The operation method shows as below. Step 1: Connect the PC and other IP products you need to control to the Switch. You can use PC or PAD to play the video stream. The connection diagram is shown as below.
Step 2: Set the PC’s IP address to the same network segment with Switch, for instance, set the IP address to be 169.254.3.30 and Subnet mask to be 255.255.0.0. 169 168 1 10 30 Step 3: Enter the default IP address (169.254.3.1) of Web GUI into the web browser on PC. The following login interface will appear.
Select the Username from the list and enter the password. The default passwords are: Username Password User user Admin admin After entering the password, click the “LOGIN” button and the following Status page will appear. Note: Status, Video, Network and Update pages are only accessible in Admin mode. When User mode is used, only the Status page is available. ■ Status Page The Status page provides basic information about the installed firmware version and the network settings.
■ Video Page The Video page allows you to set the Dectype coding (H264 / H265), resolution and bitrate for MainStream and SubStream. After setting, you need to reconnect to the video stream address. ■ Network Page The Network page allows the configuration of the network settings. Note that the IP Settings can be set only when the Mode button is set to Static. The Web login password can be changed on this page.
■ Update Page This page is used to update the software of preview module, restore the factory default settings and reboot the preview module. 8.2 VLC Media Player Instruction After the Web GUI is successfully connected, open the VLC media player on PC. Please see the following icon.
Click “Media > Open Network Stream” After clicking the “Open Network Stream” option, the following page will appear.
Enter a MainStream or SubStream network URL, then click “Play” button. Stream MainStream Network URL SubStream rtsp://169.254.3.1/live/sub/av_stream rtsp://169.254.3.1/live/main/av_stream If you enter a MainStream network, please use the MainStream of Web GUI to set the Dectype, Resolution and Bitrate value of the VLC media player. At the same time, you can check the settings on VLC media player. Choose “Tools>Codec information” to check current codec and resolution. Please see the following picture.
Choose “Tools>Codec information>Statistics” to check current Bitrate. Please see the following picture. Note that the Bitrate is floating up and down when you check it. This is a normal phenomenon. 9. Switch Mode The following Switch model is highly recommended.
10.
