INFP1595Sat4000-OM 10/18/04 2:41 PM Page 1 TSS-4000 TOTAL SPEAKER SOLUTIONS TSS-SAT4000 Owner’s Guide
INFP1595Sat4000-OM 10/18/04 2:41 PM Page 2 TSS-SAT4000 OWNER’S GUIDE Table of Contents 3 Introduction 4 Planning Your System 4 Placement 5 Installation 5 Tabletop/Shelf Placement Assembly 8 Wall-Mounting the TSS-SAT4000 Using the Included Wall Bracket 9 10 2 TSS-SAT4000 Wiring the Speaker Specifications
INFP1595Sat4000-OM 10/18/04 2:41 PM Page 3 INTRODUCTION Infinity Total Solutions™ Infinity Total Solutions continues Infinity’s longstanding commitment to accurate sound reproduction. Our proprietary Metal Matrix Diaphragm™ (MMD®) drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromised performance in any stereo or multichannel home theater system. In addition, these speakers are magnetically shielded for safe placement adjacent to a television.
INFP1595Sat4000-OM 10/18/04 2:41 PM Page 4 PLANNING YOUR SYSTEM PLACEMENT Before deciding where to best place your speakers, survey your room and study Figures 1 and 2. NOTE: The satellite speakers can be placed directly on a shelf using one of the three included shelf stands, or mounted on a wall using the included wall brackets. Optional floor stands and in-wall recess kits are also available. Please contact your dealer.
INFP1595Sat4000-OM 10/18/04 2:41 PM Page 5 INSTALLATION Please read through this owner’s guide completely before attempting to install or connect the speakers. We understand that you may be anxious to play your new system, so we have made every effort to simplify the installation and connections of the TSS-SAT4000. Before proceeding, you should decide how you would like to install the TSS-SAT4000.
INFP1595Sat4000-OM 10/18/04 2:41 PM Page 6 Step Two Step Three For Small Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. For Small Table Stand Assembly Assemble the table stand plate, the small section and the foot. Place three nuts (provided) in base of foot and secure them in place by three screws (provided) through the top of the table stand plate.
INFP1595Sat4000-OM 10/18/04 2:42 PM Page 7 Step Two Step Four For Medium and Large Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. For Medium and Large Table Stand Assembly Use screw and washer to attach medium or large base assembly to the speaker assembly, as shown.
INFP1595Sat4000-OM 10/18/04 2:42 PM Page 8 Wall-Mounting the SAT-4000 Using the Included Wall Bracket The customer is responsible for proper selection and use of mounting hardware, and for correctly and safely wall-mounting the speakers. Step Four Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. End Cap Step One Remove the wall-bracket cover by removing the four wall bracket screws on the ends as shown.
INFP1595Sat4000-OM 10/18/04 2:42 PM Page 9 Step Six The wall-bracket design allows for rotation of the speakers at angles up to 30 degrees of center. Position the speakers so they face toward the primary listening position, before fully tightening. 2 1 – WIRING THE SPEAKER After placing the speaker, you are ready to connect it to your system. First, turn off all audio-system power. Use high-quality speaker wire to make the connections.
INFP1595Sat4000-OM 10/18/04 2:42 PM Page 10 SPECIFICATIONS TSS-SAT4000 OPTIONAL ACCESSORIES Frequency Response 120Hz – 20kHz (±3dB) Nominal Impedance 8 ohms Sensitivity (2.
INFP1595Sat4000-OM 10/18/04 2:42 PM Page 11 NOTES TSS-SAT4000 11
INFP1595Sat4000-OM 10/18/04 2:41 PM Page 12 © 2004 Harman International Industries, Incorporated Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com * Trademarks of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. Infinity and MMD are registered trademarks, and Total Solutions and Metal Matrix Diaphragm are trademarks, of Harman International Industries, Incorporated. Part No.
