TSS-SAT1200 OM 7/27/06 4:44 PM Page 1 TOTAL SPEAKER SOLUTIONS TSS-SAT1200 Owner’s Guide
TSS-SAT1200 OM 7/27/06 4:44 PM Page 2 TSS-SAT1200 OWNER’S GUIDE Table of Contents 2 3 Introduction 3 Included 3 Planning Your System 3 Placement 4 Wall-Mounting the Satellites 6 Connections 6 Maintenance and Service 7 Specifications TSS-SAT1200
TSS-SAT1200 OM 7/27/06 4:44 PM Page 3 INTRODUCTION PLACEMENT Infinity Total Solutions ™ Infinity Total Solutions continues Infinity’s longstanding commitment to accurate sound reproduction. Our high-quality drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromised performance in any multichannel home theater system. In addition, the TSS-SAT1200 is magnetically shielded for safe placement adjacent to a television.
TSS-SAT1200 OM 7/27/06 4:44 PM Page 4 WALL-MOUNTING THE SATELLITES TSS-SAT1200 satellites are designed to also be mounted on the wall.There is a fixed-mount wall bracket and an adjustable wall bracket provided for each satellite. Each speaker bracket will require up to four 1-1/2" #10 wood screws; each screw should be fastened to a wall stud. If a wall stud is unavailable, install an anchor appropriate for a 1-1/2" #10 screw.
TSS-SAT1200 OM 7/27/06 4:44 PM Page 5 Step 5. Screw the ball and shaft assembly (B) to the lower 1/4"20 insert on the rear of the satellite, until it is fully seated. Back out 1/2 of a turn and tighten the nut against the speaker. Securely tightening this nut against the speaker enclosure is very important; otherwise, performing Step 7 may dislodge the threaded insert on the speaker enclosure, rendering it unusable. ® Step 6. Attach speaker wire as shown on page 7. Step 7.
TSS-SAT1200 OM 7/27/06 4:44 PM Page 6 CONNECTIONS MAINTENANCE AND SERVICE After placing the speakers, you are ready to connect your system. First, turn off all audio system power. Use high-quality speaker wire to make your connections; #18-gauge speaker wire with polarity coding is recommended. For longer distances, #16gauge or heavier wire is recommended.The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +).
TSS-SAT1200 OM 7/27/06 4:44 PM Page 7 SPECIFICATIONS TSS-SAT1200 Frequency Range: 120Hz – 30,000Hz (±3dB) Recommended Amplifier Power Range: 10 – 125 Watts Sensitivity: 89dB (2.83V @ 1 meter) Nominal Impedance: 8Ω Crossover Frequency: 3.5kHz; 24dB/octave Midrange Driver(s): Dual 3-1/2" (64mm) MMD® magnetically shielded High-Frequency Driver: 3/4" (19mm) MMD magnetically shielded Dimensions (H x W x D): 12-15/16" x 3-15/16" x 3" (329mm x 100mm x 76mm) Weight: 3.9 lb (1.
TSS-SAT1200 OM 7/27/06 4:44 PM Page b © 2006 Harman International Industries, Incorporated. All rights reserved. Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA www.infinitysystems.com Infinity, Harman International and MMD are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Total Solutions is a trademark of Harman International Industries, Incorporated. Part No.
