System Board User’s Manual Carte Mère Manuel Pour Utilisateur System-Platine Benutzerhandbuch Manual del Usuario de Placas Base Ðóêîâîäñòâî Ïîëüçîâàòåëÿ 935-CK8045-500 86510523
Quick Setup Guide 1 Quick Setup Guide Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only.
Table of Contents Chapter 1 Quick Setup Guide............................................. 4 1 Quick Setup Guide Quick Setup Guide Chapter 2 English...................................................................... 14 Chapter 3 Français.................................................................... 17 Chapter 4 Deutsch............................................................................... 20 Chapter 5 Español............................................................................
Quick Setup Guide 1 4 Quick Setup Guide Chapter 1 - Quick Setup Guide System Board Layout
Quick Setup Guide Quick Setup Guide Jumpers 1 Clear CMOS Data 1 JP2 X 2 3 1 1-2 On: Normal (default) 2 3 2-3 On: Clear CMOS Data PS/2 Power Select JP7 X 1 2 3 1-2 On: 5V (default) 1 2 3 2-3 On: 5VSB Important: The 5VSB power source of your power supply must support ≥720mA.
Quick Setup Guide 1 Quick Setup Guide USB Power Select USB 1-4 (JP5) X 2 2 1 1 1-2 On: 5V (default) 1 USB 5-10 (JP6) 3 3 2 3 X 1-2 On: 5V (default) 2-3 On: 5VSB 1 2 3 2-3 On: 5VSB Important: If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the 5VSB power source of your power supply must support ≥1.5A. For 3 or more USB ports, the 5VSB power source of your power supply must support ≥2A.
Quick Setup Guide PS/2 Mouse Parallel LAN Quick Setup Guide Rear Panel I/O Ports 1 Line-in Line-out Mic-in PS/2 K/B S/PDIF-in COM USB 1-2 USB 3-4 S/PDIF-out I/O Connectors S/PDIF-out/in and CD-in Connectors W S/PDIF-out S/PDIF-in W J3 +5V Key SPDIF out GND SPDIF in 1 5 Optical S/PDIF 1 Left audio channel Ground Ground Right audio channel W 4 CD-in Note: DO NOT use RCA S/PDIF and optical S/PDIF at the same time.
Quick Setup Guide Universal Serial Bus Ports USB 2 USB 1 W Quick Setup Guide 1 W VCC -Data +Data Ground N. C.
Quick Setup Guide Quick Setup Guide Audio (Rear Audio and Front Audio) AuD_L_Out N. C.
Quick Setup Guide 1 Quick Setup Guide Serial ATA Connectors SATA 1 (J11) 7 1 X 1 1 GND RXP RXN GND TXN TXP GND SATA 2 (J13) 7 1 GND RXP RXN GND TXN TXP GND SATA 4 7 (J10) SATA 3 7 (J2) Important: Before creating RAID, make sure you have installed the Serial/Parallel ATA drives and connected the data cables otherwise you won’t be able to enter the NVIDIA RAID BIOS utility.
Quick Setup Guide Quick Setup Guide IrDA Connector 1 IRRX Ground N. C. VCC IRTX 5 1W Note: The sequence of the pin functions on some IR cable may be reversed from the pin function defined on the system board. Make sure to connect the cable connector to the IR connector according to their pin functions.
Quick Setup Guide 1 Quick Setup Guide LEDs DRAM Power LED Standby Power LED Power Connectors +12V Ground X 4 3 2 1 Ground +12V 13 1 +3.3VDC +3.3VDC COM +5VDC COM +5VDC COM PWR_OK +5VSB +12VDC +12VDC +3.3VDC +3.3VDC -12VDC COM PS_ON# COM COM COM X NC +5VDC +5VDC +5VDC COM 2412 Important: To ensure that adequate power is provided, we strongly recommend that you use a minimum of 400 Watt (or greater) power supply.
Quick Setup Guide Quick Setup Guide Front Panel Connectors 1 ATX-SW PWR-LED J19 2 X1 20 19 HD-LED SPEAKER RESET Pin Pin Assignment HD-LED (Primary/Secondary IDE LED) 3 5 HDD LED Power HDD Reserved 14 16 N. C. N. C. ATX-SW (ATX power switch) 8 10 PWRBT+ PWRBT- Reserved 18 20 N. C. N. C. RESET (Reset switch) 7 9 Ground H/W Reset SPEAKER (Speaker connector) 13 15 17 19 Speaker Data N. C.
