TSS-SAT800 OM 2/17/06 12:20 PM Page 1 TOTAL SPEAKER SOLUTIONS TSS-SAT800 Owner’s Guide
TSS-SAT800 OM 2/17/06 12:20 PM Page 2 TSS-SAT800 OWNER’S GUIDE Table of Contents 2 3 Introduction 3 Included 3 Planning Your System 3 Placement 4 Wall-Mounting the Satellites 6 Connections 6 Maintenance and Service 7 Specifications TSS-SAT800
TSS-SAT800 OM 2/17/06 12:20 PM Page 3 INTRODUCTION PLACEMENT Infinity Total Solutions ™ Infinity Total Solutions continues Infinity’s longstanding commitment to accurate sound reproduction. Our high-quality drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromised performance in any multichannel home theater system. In addition, the TSS-SAT800 is magnetically shielded for safe placement adjacent to a television.
TSS-SAT800 OM 2/17/06 12:20 PM Page 4 Using the Satellite on the Shelf Stand To attach the satellite to the shelf stand, hold the satellite on top of the stand and insert the two included screws through the rear of the stand and into the rear of the speaker. Adjustable Wall Bracket Step 1. Mark the positions on the wall where you would like to place the mounting screws. Step 2. Place the bracket against the wall and fasten four 1-1/2" #10 wood screws through the bracket’s screw holes into the wall.
TSS-SAT800 OM 2/17/06 12:20 PM Page 5 ® Step 4. Screw the ball and shaft assembly (B) to the lower 1/4"20 insert on the rear of the satellite. Back out 1/2 of a turn and tighten the nut against the speaker. Step 5. Attach the speaker wire as shown on page 6. Step 6. Drop round collar (C) over ball and shaft assembly (B) that is mounted to the speaker with the finished side of the collar facing the rear of the speaker. Step 7.
TSS-SAT800 OM 2/17/06 12:20 PM Page 6 CONNECTIONS MAINTENANCE AND SERVICE After placing the speakers, you are ready to connect your system. First, turn off all audio-system power. Use high-quality speaker wire to make your connections; #18-gauge speaker wire with polarity coding is recommended. For longer distances, #16gauge or heavier wire is recommended.The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +).
TSS-SAT800 OM 2/17/06 12:20 PM Page 7 SPECIFICATIONS TSS-SAT800 Frequency Range: 120Hz – 30,000Hz (±3dB) Recommended Amplifier Power Range: 10 – 100 Watts Sensitivity: 88dB (2.83V @ 1 meter) Nominal Impedance: 8Ω Crossover Frequency: 3.5kHz; 12dB/octave Midrange Driver(s): 3-1/2" (64mm) MMD® magnetically shielded High-Frequency Driver: 3/4" (19mm) MMD magnetically shielded Dimensions (H x W x D): 9-1/8" x 3-3/4" x 2-3/4" (232mm x 95mm x 70mm) Weight: 2.5 lb (1.
TSS-SAT800 OM 2/17/06 12:20 PM Page b © 2006 Harman International Industries, Incorporated. All rights reserved. Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA www.infinitysystems.com Infinity and Harman International are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Total Solutions is a trademark of Harman International Industries, Incorporated. Dolby and Pro Logic are registered trademarks of Dolby Laboratories.
