CS50-60-80 OM 8/6/04 1:18 PM Page 1 CS SE R I E S CS 50 CS 60 CS 60R CS 60RDT CS 80R Owner’s Guide
CS50-60-80 OM 8/6/04 1:18 PM Page 2 CS SERIES OWNER’S GUIDE 3 Introduction 3 Planning Your System 4 Placement 4 Installation 5 Speaker Connections 6 Existing Construction 7 Specifications
CS50-60-80 OM 8/6/04 1:18 PM Page 3 INTRODUCTION PLANNING YOUR SYSTEM Infinity CS Series Before deciding where to best place your speakers, survey your room and study Figures 1 and 2. The CS Series of in-wall/ceiling loudspeakers continues Infinity’s longstanding commitment to accurate sound reproduction. All CS Series speakers deliver uncompromised performance in any stereo, multichannel home theater or whole-house music system.
CS50-60-80 OM 8/6/04 1:18 PM Page 4 PLACEMENT Stereo CS 60RDT Before deciding where to place your CS Series speakers, survey your room and think about placement, keeping the following points in mind, and using Figure 1 as a guide: Model CS 60RDT has the ability to play two channels through one loudspeaker, thanks to its dual-tweeter/dual-voice-coil construction. Since the tweeters are close together, generally they should be aimed away from each other for best coverage.
CS50-60-80 OM 8/6/04 1:18 PM Page 5 SPEAKER CONNECTIONS Figure 3. Wire Length Recommended Size Up to 50 ft. 16-gauge Up to 100 ft. 14-gauge Greater than 100 ft. 12-gauge Turn Off All Power Before completing the installation, you must connect your speakers to your system. First, turn off all audio-system power. Use high-quality speaker wire to make your connections. Use at least #16-gauge speaker wire with polarity coding. Heavier gauge wire is recommended for larger distances.
CS50-60-80 OM 8/6/04 1:18 PM Page 6 EXISTING CONSTRUCTION CS 60R, CS 60RDT, CS 80R CS 50, CS 60 Template 1. Remove the grille from the speaker frame. 2. Determine the correct speaker location. NOTE: Remove the inner template, which is the paint shield, at the perforation. Use the outer template when cutting the drywall. 1. Remove the grille from the speaker frame. 2. Determine the correct speaker location. NOTE: Remove the inner template, which is the paint shield, at the perforation.
CS50-60-80 OM 8/6/04 1:18 PM Page 7 SPECIFICATIONS CS 50 CS 60 CS 60R CS 60RDT CS 80R Frequency Range 48Hz – 20kHz (±3dB) 45Hz (–10dB) 45Hz – 20kHz (±3dB) 38Hz (–10dB) 50Hz – 20kHz (±3dB) 40Hz (–10dB) 50Hz – 20kHz (±3dB) 40Hz (–10dB) 45Hz – 20kHz (±3dB) 32Hz (–10dB) Recommended Amplifier Power Range 10 – 75 watts 10 – 100 watts 10 – 100 watts 10 – 100 watts total (50WPC) 10 – 100 watts Sensitivity 87dB 88dB 88db 88dB, both channels driven 89dB Nominal Impedance 8Ω 8Ω 8Ω 8Ω per
CS50-60-80 OM 8/6/04 1:18 PM Page 8 © 2004 Harman International Industries, Incorporated Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516.674.4INF (4463) www.infinitysystems.com Infinity is a registered trademark of Harman International Industries, Incorporated. Part No.
